Panasonic SC-HC49DB Operating Instructions Manual page 16

Bluetooth ®
Pairing cannot be completed.
≥ Check the Bluetooth
The device cannot be connected.
≥ The pairing of the device was unsuccessful or the registration has
been replaced. Try re-pairing the device. (l 7)
≥ This unit might be connected to a different device. Disconnect the
other device and try re-pairing the device. (l 7)
The device is connected, but audio cannot be
heard through this unit.
≥ For some built-in Bluetooth
output to "SC-HC49" manually. Read the operating instructions for
the device for details.
The sound is interrupted.
≥ The device is out of the 10 m communication range. Place the
Bluetooth ® device closer to this unit.
≥ Remove any interference between this unit and the device.
≥ Other devices that use the 2.4 GHz frequency band, such as
wireless routers, microwaves, cordless phones, etc. are
interfering. Place the Bluetooth
distance it from the other devices.
≥ Select "MODE 1" for stable communication. (l 8)
The One-Touch Connection (NFC feature) is not
working.
≥ Make sure the unit and the NFC feature of the device are turned
on. (l 7)
Messages
The following messages or service numbers may
appear on the unit's display.
"--:--"
≥ You plugged the AC mains lead in for the first time or there was a
power failure recently. Set the time (l 13).
"ADJUST CLOCK"
≥ Clock is not set. Adjust the clock accordingly.
"ADJUST TIMER"
≥ Play timer is not set. Adjust the play timer accordingly.
"AUTO OFF"
≥ The unit has been left unused for about 20 minutes and will shut
down within a minute. Press any button to cancel it.
"CHECKING CONNECTION"
≥ The unit is checking the connected iPhone/iPad/iPod.
≥ If this display keeps appearing, make sure that the battery of the
iPhone/iPad/iPod is not depleted and that the iPhone/iPad/iPod is
turned on and connected correctly (l 6).
"ERROR"
≥ Incorrect operation is performed. Read the instructions and try
again.
"F " (" " stands for a number.)
≥ There is a problem with this unit.
Write down the displayed number, disconnect the AC mains lead
and consult your dealer.
"ILLEGAL OPEN"
≥ Sliding door is in the wrong position. Turn the unit off and on
again. If this display appears again, consult the dealer.
16
RQT9883
®
device condition.
® devices, you have to set the audio
®
device closer to this unit and
"IPOD_DOCK OVER CURRENT ERROR"
"USB OVER CURRENT ERROR"
≥ The iPhone/iPad/iPod is drawing too much power. Disconnect the
iPhone/iPad/iPod and turn the unit off and on again.
≥ The USB device is drawing too much power. Select a source other
than "USB", remove the USB and turn the unit off.
"NODEVICE"
≥ The iPhone/iPad/iPod or USB device is not inserted correctly.
Read the instructions and try again (l 6).
≥ The battery of the iPhone/iPad/iPod is depleted. Charge the
iPhone/iPad/iPod and turn it on before connecting.
"NO DISC"
≥ Insert the disc to be played (l 6).
[SC-HC49DB]
"NO MEMORY"
≥ There are no preset DAB+ stations to select. Preset some
channels. (l 10)
"NO PLAY"
≥ A CD that is not in CD-DA or MP3 format is inserted. It cannot be
played.
≥ Examine the content. You can only play supported format. (l 18)
≥ The files in the USB device can be corrupted. Format the USB
device and try again.
≥ The unit may have a problem. Turn the unit off and then on again.
[SC-HC49DB]
"NO SIGNAL"
≥ This station cannot be received. Check your antenna (l 5).
"NOT SUPPORTED"
≥ You have connected an iPhone/iPad/iPod that cannot be played
(l 18).
≥ If the iPhone/iPad/iPod is compatible, turn it on and connect it
correctly.
"PLAYERROR"
≥ You played an unsupported MP3 file. The system will skip that
track and play the next one.
"READING"
≥ The unit is checking the CD information. After this display has
disappeared, start operating.
"REMOTE " (" " stands for a number.)
≥ The remote control and this unit are using different codes. Change
the code on the remote control.
– When "REMOTE 1" is displayed, press and hold [OK] and [
for at least 4 seconds.
– When "REMOTE 2" is displayed, press and hold [OK] and [CD/
RADIO] for at least 4 seconds.
[SC-HC49DB]
"SCAN FAILED"
≥ Stations are not receivable. Check your antenna and try Auto
scanning (l 10).
If "SCAN FAILED" is still displayed find the best signal reception
with the "MANUAL SCAN" tuning function. (l 11)
"VBR"
≥ The system cannot show the remaining play time for variable bit
rate (VBR) tracks.
]