Initial Auto Installation; Checking Signal Strength And Channel Strength - Sharp LC-70LE735X Aquos Operation Manual

Quick guide

Initial auto installation

When the TV is powered on for the first time after
purchase, the initial auto installation wizard appears.
Follow the menus and make the necessary settings one
after another.
Confirm the following before turning on the
power
E
Is the antenna cable connected?
E
Is the AC cord plugged in?
1
Press < on the TV.
• The initial auto installation
wizard appears.
2
Setting the OSD language.
Press a/b to select the desired language, and then press
A.
3
Selecting the location of the TV.
Press c/d to select where you will use this TV, and then
press A.
HOME:
• Settings are optimised for normal home viewing and
energy efficiency.
• "STANDARD" will be the default value for the "AV mode"
setting.
STORE:
• Settings are designed for maximum impact in retail store
displays.
• "DYNAMIC (Fixed)" will be the default value for the "AV
mode" setting. If the "AV mode" is changed, the TV will
automatically switch back to "DYNAMIC (Fixed)" when
there is no operation using the TV or remote control unit
for 30 minutes.
• The confirmation screen pops up only when selecting
"STORE". Press c/d to select "Yes" or "No".
* This product qualifies for ENERGY STAR in "HOME"
mode default setting.
* ENERGY STAR qualification is based on "STANDARD" in
the "AV mode" menu.
NOTE
• STORE: A demonstration image will be displayed after initial
auto installation is completed. If you have chosen "STORE"
by mistake, go to "Setup" > "View setting" > "Reset" > select
"HOME" again.
4
Setting the country.
Press a/b to select your country or area, and then press
A.
• This setting screen only appears during the initial auto
installation.
5
Press c/d to select "Digital search" or "Analogue
search", and then press A.
6
The TV searches for, sorts and stores all the
receivable TV stations according to their settings
and the connected antenna.
• To abort the initial auto installation in progress, press
C.
14
NOTE
• If you turn off the power on the TV while performing a channel
search in Step 5, the initial auto installation wizard may not
appear. The auto installation function allows you to execute
the installation again from "Setup" > "View setting" (Page 34).
• The initial auto installation wizard will abort if you leave the TV
unattended for 30 minutes before searching for channels in
Step 6.
Checking signal strength and
channel strength
If you install a DTV antenna for the first time or relocate it,
you should adjust the alignment of the antenna to receive
a good reception while checking the antenna setup
screen.
1
Go to "HOME" > "TV Menu" > "Setup" > "View
setting" > "Channel settings" > "Antenna setup-
DIGITAL".
E
Checking signal strength
2
Press a/b to select "Signal strength", and then
press A.
Supply voltage
Signal strength
Channel strength
E
Checking channel strength
3
Press a/b to select "Channel strength", and then
press A.
• You can input a specified frequency band using the 0–9
numeric buttons.
Supply voltage
Signal strength
Channel strength
4
Position and align the antenna so that the
maximum possible values for "Signal strength"
and "Quality" are obtained.
NOTE
• The values of "Signal strength" and "Quality" indicate when to
check the appropriate alignment of the antenna.
Supplying power to the antenna
You can supply power to the antenna in order to receive
digitally/terrestrially broadcast stations after connecting
the antenna cable to the antenna terminal on the rear of
the TV.
1
Go to "HOME" > "TV Menu" > "Setup" > "View
setting" >"Channel settings" > "Antenna setup-
DIGITAL" >"Supply voltage".
2
Press c/d to select "On", and then press
A.
CH No.
Signal strength
Current Max.
97 97
Quality
Current Max.
99 99
Frequency
MHz
CH No.
Signal strength
Current Max.
97 97
Quality
Current Max.
99 99