Husqvarna 266 Operator's Maintenance Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Chainsaw
  5. 266
  6. Operator's maintenance manual

Husqvarna 266 Operator's Maintenance Manual

Husqvarna chainsaw user manual
Hide thumbs Also See for 266:
Table of Contents

Advertisement

Quick Links

Chain saw

266
model
TECHNICAL SPECIFICATION
Displacement . . . . 66.7 cm
Bore . . . . . . . . . . . 50 mm
Stroke . . . . . . . . . . 34 mm
Ignition advance . . . . . 25˚ before t.d.c. at 8500 rpm
Sparking Plug . . . .
Champion CJ 7Y, PAL P8Y
Electrode gap . . . . 0.5 mm
Carburettor . . . . . . Diaphragm type
Tillotson HS 163 A
Operator's maintenance manual
3
Fuel tank capacity . . . .0.75 l
Oil tank capacity . . . . . 0.45 l
Sawing chain. . . . . . .3/8" pitch
Guide Bar . . . . . . . . . . 15"
Weight empty, incl. 15"
guide bar , chain . . . . . 7.1 kg (SE)
and chain brake . . . . . 7.25 kg (SG)

Advertisement

Table of Contents
loading

Related Manuals for Husqvarna 266

Summary of Contents for Husqvarna 266

  • Page 1: Specifications

    Chain saw model TECHNICAL SPECIFICATION Displacement ..66.7 cm Bore ... 50 mm Stroke ..34 mm Ignition advance ..25˚ before t.d.c. at 8500 rpm Sparking Plug .

  • Page 2: Chainsaw Overview

    “wintergrade” stays fluent even when cold. Concerning the choice of oil and its suit- ability at different air temperatures, please refer to your Husqvarna waste oil should be used as this can damage Oil 1:50 (270). oil 1:25 (47.) (5Yo).

  • Page 3: Adjusting Release Power

    Chain brake activator “Swed-o-Matic” The Swed-o-Matic should release the chain brake at a certain on the guide bar tip. Adjusting the release power The distance between the Swed-o-Matic front handle (see fig.) determines the release power. A smaller gap means reduced release power.

  • Page 4: Starting Chain Saw

    Starting the chain saw A. Cold engine 1. Switch on the ignition (push the switch to the left so that the 1 is visible). 2. Pull out the choke control 3. Push down the throttle trigger lockout 4. Open the throttle fully (B) 5.

  • Page 5: Cleaning The Air Filter

    Cleaning the air filter A clean air filter is necessary for optimal carburetor optimal engine power. Fig. 11 In order to get at the air filter, remove the cylinder the retaining screws and lifting the cover off upwards-backwards. Remove the heaviest dirt from the air filter.

  • Page 6: Oil Pump Capacity

    Fig. 15 Assemble the remaining parts in reverse order. Lift up the starter cord into the notch on the pulley. Tension return spring by turning the pulley clockwise NOTE! Make sure that it is possib/e to turn the pulley at least 1/4 of a turn further when the cord is fu//y pu//ed out.
  • Page 7 Maintenance of the chain saw Fig. 19 Daily maintenance 1. Clean the saw body from the outside. 2. Clean the air filter. Change if necessary 3. Turn around the guide bar, lower edge up. Clean the bar groove. 4. Clean the fan and air intakes in the starter cover.

  • Page 8: Safety Reminders

    Safety reminders Handling When transporting the saw, fit the chain protection. 2. Do not smoke when filling the fuel tank. 3. Before cutting, fix the barking support 4. When using the saw, keep both hands on the handles. 5. Nobody is allowed to be within the swing area of the saw.

Table of Contents