Planet VIP-281 Series User Manual
  1. Manuals
  2. Brands
  3. Planet Manuals
  4. Gateway
  5. VIP-281 Series
  6. User manual

Planet VIP-281 Series User Manual

2~24-port h.323/sip voip gateway
Hide thumbs Also See for VIP-281 Series:
Table of Contents

Advertisement

Quick Links

2~24-Port H.323/SIP VoIP Gateway
VIP-281/480/880/1680/2480 series
User's manual
Version 2.1.0

Advertisement

Table of Contents
loading

Related Manuals for Planet VIP-281 Series

Summary of Contents for Planet VIP-281 Series

  • Page 1 2~24-Port H.323/SIP VoIP Gateway VIP-281/480/880/1680/2480 series User’s manual Version 2.1.0...
  • Page 2 PLANET has made every effort to ensure that this User’s Manual is accurate; PLANET disclaims liability for any inaccuracies or omissions that may have occurred.
  • Page 3 Trademarks The PLANET logo is a trademark of PLANET Technology. This documentation may refer to numerous hardware and software products by their trade names. In most, if not all cases, their respective companies claim these designations as trademarks or registered trademarks.

  • Page 4: Table Of Contents

    TABLE OF CONTENTS Chapter 1 Introduction................6 Overview..........................6 Package Content .......................8 Physical Details .........................9 Front Panel LED Indicators & Rear Panels..............10 Chapter 2 Preparations & Installation ..........13 Physical Installation Requirement ................13 LAN/WAN Interface quick configurations...............14 LAN IP address configuration via web configuration interface.......14 WAN IP address configuration via web configuration interface ......15 Chapter 3 Network Service Configurations........
  • Page 5 FAQ 8: Peer to Peer call for one shoot dialing: FXO to FXO........83 FAQ 9: Peer to Peer call: Hotline setting ..............85 FAQ 10: SIP speed call setting .................87 Appendix C................... 89 VIP-281 series Specifications...................89 VIP-480 series Specifications...................90 VIP-880 series Specifications...................91 VIP-1680 series Specifications.................92...

  • Page 6: Chapter 1 Introduction

    Overview With years of Internet telephony and router manufacturing experience, PLANET proudly introduces the newest member of the PLANET VoIP gateway family: the VIP-GW, VIP-281 / VIP-480 / VIP-880 / VIP-1680 / VIP-2480 series. The PLANET VoIP Gateway is fully both SIP and H.323 standard compliant residential gateway that...
  • Page 7 VIP-281FS equips two FXS interfaces telephone set or FAX machine connection (FXS). 4-Port Model - VIP-480 equips two FXO and two FXS interfaces to have the great flexibility of PBX connection (FXO), and telephone set or FAX machine connection (FXS). VIP-480FS equips four FXS interfaces telephone set or FAX machine connection (FXS).

  • Page 8: Package Content

    • Point-to-Point Protocol over Ethernet (PPPoE) Client Support: If you are a DSL user, the router has a built-in PPPoE client for establishing a DSL link connection with the ISP. There is no need to install a further PPPoE driver on your computers. •...

  • Page 9: Physical Details

    RS-232 cable x 1 (8 / 16 / 24-port model) 25 port Telephone Cable x 1 (16 / 24-port model) Rack mount brackets x 2 (16 / 24-port model) Physical Details The following figure illustrates the front/rear panel of VIP-GW series: Front Panel of VIP-281/VIP-281FS Rear Panel of VIP-281/VIP-281FS Front Panel of VIP-480/VIP-480FS/VIP-480FO...

  • Page 10: Front Panel Led Indicators & Rear Panels

    Rear Panel of VIP-880/VIP-880FS/VIP-880FO Front Panel of VIP-1680/VIP-1680FS/VIP-1680FO/VIP-1680FD Front Panel of VIP-2480/VIP-2480FS/VIP-2480FO/VIP-2480FD Rear Panel of VIP-1680/VIP-1680FO/VIP-2480/VIP-2480FO Front Panel LED Indicators & Rear Panels Front Panel LED State Descriptions GW is powered ON GW is powered Off Flashing The system is running (VIP-880 / VIP-1680 / VIP-2480 series) WAN Port...
  • Page 11 NOTE: System initialization will turn some LEDs ON for a few seconds. The Default LAN IP is http://192.168.0.1. Press RESET button Note on rear panel over 5 seconds will reset the VoIP Gateway to this default LAN/WAN IP address and Username/Password function.
  • Page 12 (CO line), and the FXS interface is designed for connecting to analog telephone sets or fax machines. If the telephone cable connects to VIP-16/2480 series, the FXS interfaces are odd ports i.e. 1, 3, 5, 7, 9, 11, 13, 15, 17, 19, 21, 23, and the FXO interfaces are even ports, i.e. 2, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24.

  • Page 13: Chapter 2 Preparations & Installation

    For Internet Access, an Internet Access account with an ISP, and either of a DSL or Cable modem (for WAN port usage) Administration Interface PLANET VIP-GW provides GUI (Web based, Graphical User Interface) for machine management and administration. Web configuration access...

  • Page 14: Lan/Wan Interface Quick Configurations

    LAN/WAN Interface quick configurations Nature of PLANET VIP-GW is an IP Sharing (NAT) device, it comes with two default IP addresses, and default LAN side IP address is “192.168.0.1”, default WAN side IP address is “172.16.0.1”. You may use any PC to connect to the LAN port of VIP-GW to start machine administration.

  • Page 15: Wan Ip Address Configuration Via Web Configuration Interface

    Parameter Description LAN IP address of VIP-GW IP address Default: 192.168.0.1 LAN IP address of VIP-GW Subnet Mask Default: 255.255.255.0 Hint It is suggested to keep the DHCP server related parameters in default state to keep machine in best performance. After confirming the modification you’ve done, Please click on the Apply button to macke the changes Save Configuration”...

  • Page 16: Chapter 3 Network Service Configurations

    Chapter 3 Network Service Configurations Configuring and monitoring your VoIP Gateway from web browser The VIP-GW integrates a web-based graphical user interface that can cover most configurations and machine status monitoring. Via standard, web browser, you can configure and check machine status from anywhere around the world.

  • Page 17: Wizard Setup For Quick Start

    VIP-GW main page Wizard Setup for Quick Start Wizard Setup After finishing the authentication, the Main menu will display 3 parts of configuration, please click “Wizard Setup” to enter quick start: 1. WAN Port Type Setup (Setup First) For most users, Internet access is the primary application. The VIP-GW support the WAN interface for Internet access and remote access.
  • Page 18 check with your ISP provider Default Gateway ADSL Dial-Up User (PPPoE Enable) Some ISPs provide DSL-based service and use PPPoE to establish communication link with end-users. If you are connected to the Internet through a DSL line, check with your ISP to see if they use PPPoE. If they do, you need to select this item.

  • Page 19: Configuring Nat Or Bridge Setting

    2. Configuring NAT or Bridge setting: Bridge Mode: When working on Bride Mode, the VoIP gateway will use only the LAN setting IP, The VIP-GW will use the same LAN IP setting as WAN IP. That means, when Bride mode enable, the WAN connection setting will be ignored.

  • Page 20: Voip Call Protocol Setup

    3. VoIP Call Protocol Setup STEP 1 : Configure VoIP Call Signal Protocols : User could select either H.323 or SIP Protocol, and click “select” STEP 2 : Configure the numbering with phone/line ports The representation number is the phone number of the telephone that Phone Number is connected to phone port Line ports are connected to the extension ports of the PBX system or...
  • Page 21 STEP 4: Outgoing Dialing Plan The purpose of “Outgoing Direct Call” setting is to let user create a proprietary dialing plan when this Gateway is not registered to any H.323 Gatekeeper or any SIP proxy server. This setting can also assign some dialing plan to local ports (including prefix strip, prefix addition).

  • Page 22: Chapter 4 System Configurations

    Chapter 4 System Configurations Advance Setup of Network Setup In Advanced Setup, VIP-GW provides user two major parts function to configure: One is “Network Setup”, the other one is “VoIP Call Setup” Network Setup Label Sets/changes the WAN port type like “Fixed IP”, “DHCP WAN Setting Client”...
  • Page 23 You are a leased line user with a fixed IP address; fill out the Static IP following items with the information provided by your ISP Kindly please check with your ISP provider IP Address Kindly please check with your ISP provider Netmask Default Gateway Kindly please check with your ISP provider...

  • Page 24: Lan Setting

    Note WAN port display the IP address, Subnet Mask and default gateway IP address if DHCP client is successful LAN Setting There are two kinds of network feature to configure: Bridge Mode and NAT Mode: Bridge Mode Select this VIP-Gw as Bridge. (WAN Port and LAN Port use the same IP address) NAT Mode Each of the VIP-GW has two Ethernet interfaces, one is for connecting to...

  • Page 25: Virtual Server

    DHCP Server Configuration DHCP stands for Dynamic Host Configuration Protocol. It can automatically dispatch related IP settings to any local user configured as a DHCP client. The DHCP server supports up to 253 users (PCs) on Yes: Enables the DHCP server. No: Disables the DHCP server. Start IP Address Sets the start IP address of the IP address pool.

  • Page 26: Dynamic Dns

    Specifies which port should be redirected to the internal host. Public Port Specifies the private IP address of the internal host offering the service. Private IP Private Port Specifies the private port number of the service offered by the internal host.

  • Page 27: Netwrok Management

    Input your DDNS User Name User Name Input your DDNS Password Password Input you set from your DDNS Domain Name DNS Server IP Input your DNS Server IP Netwrok Management Network Parameter allows you to modify the access port of gateway. For example: Setting HTTP port: 80 and Setting TELNET port: 23...

  • Page 28: Advance Setup Of Voip Setup

    In Advanced Setup, VIP-GW provides user two major parts function to configure: One is “Network Setup”, the other one is “VoIP Call Setup” VoIP Setup Label The PLANET series gateway support 2~24 phone/line for SIP and VoIP Basic H.323 VoIP call applications. You can configure these ports from this menu.
  • Page 29 Configure the numbering with FXS / FXO ports. (Depending on GW model number: if user uses the model number is VIP-1680, this VIP-1680 has 16 voice channels for setting, and the VIP-2480 had 24 voice channels for setting) The representation number is the phone number of the telephone that is FXS Number connected to FXS port.
  • Page 30 H.323 Parameters Label Sets the unique name of this Gateway, that is H.323 ID communicated as part of H.323 messaging. Primary Gatekeeper IP There are two gatekeeper address fields, one is primary, the other secondary. If this gateway does not want to Address register to any gatekeeper, just set value 0 to the primary gatekeeper address.

  • Page 31: Dialing Plan To H.323 Protocol

    In H.323 standard the RAS default port number is 1719. The VoIP gateway provides user to change RAS port RAS Port Adjustment number to meet the network environment.(Some area carrier blocks or forbidden the default port number) In H.323 standard the default Q.931 port number is 1720. The VoIP gateway provides user to change Q.931 port to Q.931 Port Adjustment meet the network environment.
  • Page 32 “Add Digit Number” is the digits that will be added to the beginning of the dialed number. “Destination IP Address / Domain Name” is the IP address / Domain Name of the destination gateway that owns this phone number. Scenario description: Normally dial 001x leading call out, call to destination IP address: 172.16.0.100 002x leading call out, call to destination domain name: h323gw.test.com Scenario description: Speed dial...
  • Page 33 “Length of Number“ has two text fields need filled: “Min Length” and “Max Length” is the min/max allowed length you can dial. “Delete Length” is the number of digits that will be stripped from beginning of the dialed number. “Add Digit Number” is the digits that will be added to the beginning of the dialed number. “Destination telephone port”...
  • Page 34 Scenario description: Hunting for FXO port (VIP-480FO) Port 1: FXO was connected to PSTN. Port 2: FXO was connected to PSTN. Port 3: FXO was connected to PSTN. Port 4: FXO was connected to PSTN. H.323 number “123” call incoming, the port 1 will be off-hook and hear the dial tone from PSTN. If port 1 is busy, the port 2 will be will be off-hook and hear the dial tone from PSTN.

  • Page 35: Advance Setting To H.323 Protocol

    Scenario description: Termination call to FXO for one-shoot call Port 1: FXO was connected to PSTN (area code is 81xxxxxxxx). H.323 leading number “081x” incoming, and delete the first one digit “0”, and call to PSTN number. Note: “081x” will be registered to H.323 Gatekeeper if “Register to GK” was enabled, show as below: Scenario description: Termination call to FXO Port 1: FXS Port 1: FXO was connected to PSTN (area code is 92xxxxxxxx).
  • Page 36 H.323 VoIP Advance Configurtion If this function is enabled, when VoIP call is occurred, the other Smart-QoS data will be automatically reduced traffic which across the internet in order to guarantee the voice bandwidth. After the VoIP call is connected, when you dial a digit, this digit is sent to the other side by DTMF tone.
  • Page 37 The T.38 is a “Real Time Group 3 FAX communication over IP network” format. That’s meaning it’s a protocol for Fax over IP. You have to enable this function. This command configures the number of seconds that the gateway should be considered active by the H.323 Gatekeeper. H.323 RRQ TTL The gateway transmits this value in the RRQ message to the gatekeeper.The default value is “0”.
  • Page 38 You can configure how long the Ring Frequency do you want Ring Frequency to use. Enable battery reverse to detect polarity from PSTN line. The FXO Battery Reverse PSTN line can send H.323 case: Sending the Q.931 connect signal to caller when detecting polarity reverse from PSTN line. When user calls the PSTN line which was connected with the FXO port, there are three answer mode for user to configure.
  • Page 39 Note: This case can avoid the local PSTN charge when the FXS port still ring. 3. Non Answer Mode: FXO will NOT answer the call in any time. Note: Some ITSP only let the FXO for termination function, they do not user use the FXO port for origination Scenario description: H.323 call connecting answer mode Case B: “Hot Line Number”...

  • Page 40: Voip Basic Configuration To Sip Protocol

    H.323 Netwrok Advance Configuration If this function is enabled, when VoIP call is occurred, the other data Smart-QoS will be automatically reduced traffic which across the internet in order to guarantee the voice bandwidth. Bandwidth control You can configure your bandwidth what the Max byte of download and upload of ADSL modem rate.
  • Page 41 For example: Port 1 and port 2 is hunting for the port 1 SIP account. If the port 1 is incoming call, the other one SIP call from internet will ring port 2. SIP Proxy Server Setting Enter the SIP realm in this field Domain/Realm Enter the SIP service IP address or domain name in this field (the domain name that comes after the @ symbol i n a full...

  • Page 42: Dialing Plan To Sip Protocol

    Dialing Plan to SIP protocol The “Dialing plan” needs setting when the user uses the method of Peer-to-Peer or registering SIP proxy server mode. The SIP dialing plan has two kinds of directions: Outgoing (call out) and incoming (call in). Peer-to-Peer call mode: Effective Outgoing Dial Plan Registering to SIP Proxy Server Mode: Effective...
  • Page 43 Scenario description: Normally dial 2290x leading call out, call to destination domain name: sipgw.test.com 221 leading call out, call to destination IP address: 172.16.0.100 Scenario description: Speed dial If user dials “101”, the gateway automatically dials “1234567890” to destination IP address: 172.16.0.101 If user dials “202”, the gateway automatically dials “0987654321”...
  • Page 44 Scenario description: Hunting for FXS port (VIP-400FS) Port 1: FXS Port 2: FXS Port 3: FXS Port 4: FXS H.323 number “123”call incoming, the port 1 will be ringing. If port 1 is busy, the port will be ringing. If port 1 and port 2 are busy, the port 3 will be ringing. If port 1, port 2 and port 3 are busy, the port 4 will be ringing.

  • Page 45: Advance Setting To Sip Protocol

    Note: “123” will be NOT register to SIP proxy server when gateway is registering SIP proxy server mode Scenario description: Termination call to FXO for one-shoot call Port 1: FXO was connected to PSTN (area code is 81xxxxxxxx). SIP leading number “081x” incoming, and delete the first one digit “0”, and call to PSTN number. Note: “081x”...
  • Page 46 T.30/T.38 real-time FAX compliant Voice/FAX auto-switch. The T.38 is a “Real Time Group 3 FAX communication over IP FAX Mode Option network” format. That’s meaning it’s a protocol for FAX over IP. You have to enable this function. SIP Telephone Advance Configuration If this function is enabled, when silence is occurred for a Silence Compression period of time, no data will be sent across the network...
  • Page 47 generate flash to FXS. Flash Generation: Let you change flash generation time (milliseconds) for PBX detection. Ring Frequency You can configure how long the Ring Frequency do you want to use. Enable battery reverse to detect polarity from PSTN line. The PSTN line can send SIP case: Sending the 200 OK FXO Battery Reverse connect signal to caller when detecting polarity reverse...
  • Page 48 the Phone (connected to the FXS port) was picked up by user. (Note: This case can avoid the Local PSTN charge when the FXS port still ring.) 6. Non Answer Mode: FXO will NOT answer the call in any time. (Note: Some ITSP only let the FXO for termination function, they do not user use the FXO port for origination)

  • Page 49: Voip Basic & Dialing Plan Configuration For Fxo Caller Id Model

    SIP Netwrok Advance Configuration If this function is enabled, when VoIP call is occurred, the other Smart-QoS data will be automatically reduced traffic which across the internet in order to guarantee the voice bandwidth. Bandwidth control You can configure your bandwidth what the Max byte of download and upload of ADSL modem rate.
  • Page 50 Example: ITSP_A and ITSP_B are configured in this setting. - Step 2: Configure SIP Account You can find Set Register SIP Server Plan in Advance Setting – VoIP Basic Set Register SIP Server Plan Account Input SIP account(Username) Password Input Password that ITSP support. Expires This field sets how long an entry remains registered with the SIP register server.
  • Page 51 - Step 3: Configure Least Cost Route You can find LCR Outgoing Dial Rule in Advance Setting – Dialing Plan LCR Outgoing Dial Rule It’s is the leading digits of the call out dialing number Outgoing Number Length Min Min allowed length you can dial. Length Maxi MAX allowed length you can dial.

  • Page 52: Port Status

    According the rules, the gateway can achieve the goal: Least Cost Route by making calls through relatively cheaper ITSP providers. Port Status Port Status Display: This selection will display concurrent call status of this gateway. The status information of each voice channel includes codec, dialing number and destination IP address. The status is refreshed every 3 seconds.

  • Page 53: Chapter 5 System Administrations

    Chapter 5 System Administrations Management Management Label You can save configuration and restart the gateway with the default Save Configuration configuration or with the current running configuration. Users can sets/changes the administrator password... Access Control You can restart the VIP-GW with the default configuration. Set to Default Backup/Restore User can backup the configuration file of VPI-GW to PC or restore...

  • Page 54: Save Configuration

    Save Configuration This page allows you to click “Save Configuration and Reboot” to save configuration and begin to restart. Access Control Changing the Administrator/Guest Password For security reasons, we strongly recommend that you set an administrator/password for the router. On first setup the router requires no password.

  • Page 55: Backup/Restore Configuration To A File

    Backup/Restore Configuration to a File User can backup the configuration to a File at Microsoft Operation System. And also restore the configuration file to the VIP-GW from PC. System Information Display Function Click System Information Display to open the Online Status page. In the example, on the foll owing page, both PPPoE connections is up on the WAN interface, H323/SIP Status, MAC addr ess, Register Status.., etc.

  • Page 56: Sntp Setting Function

    SNTP Setting Function Click SNTP setting to open the Online Status page. In the example, on the following page: Use SNTP Setting— when checked, gateway uses a Simple Network Time Protocol (SNTP) to set the date and time. The gateway synchronizes the gateway’s time after you select the time zone. Use SNTP Setting;...

  • Page 57: Capture Packetackets Function

    Capture packetackets Function Use “Capturer Packets” to record VIP-GW packets. Users can start and stop the capture then save the file to PC. Use the Ethereal Tool (www.ethereal.com) to analyze the packets.

  • Page 58: Appendix A

    Appendix A Voice communications The chapter shows you the concept and command to help you configure your PLANET VIP-GW through sample configuration. And provide several ways to make calls to desired destination in VIP-GW. In this section, we’ll lead you step by step to establish your first voice communication via web browsers operations.
  • Page 59 FXS (Foreign exchange Station) port The FXS port allows the connection to an end node, like telephone, fax machine, or out-line of PBX system. FXS port is as like your local phone service provider who provides a number to you. It is easy to tell that after you have connected an end-device to FXS port and you will hear the dial-tone from FXS port once the hand set off-hook.

  • Page 60: H.323 Voip Call: Peer-To-Peer Mode

    H.323 VoIP Call: Peer-To-Peer Mode Scenario 1: Gateway 1 to Gateway 2 PLAR connection H.323 Call (Peer-To-Peer Mode) Outgoing Dial plan Outgoing Dial plan No: 8x | Digit: 3~3 |Des: GW2 IP address No: 9x | Digit: 3~3 | Des: GW1 IP address x: wild card Des: Destination IP Digit: Digit Length min~ max...
  • Page 61 Scenario 3: Gateway 1 (with PBX/PSTN) to Gateway 2 PLAR connection Call Method: Two-Stages-Dialing H.323 Call (Peer-To-Peer Mode) with PBX: Remote Call PSTN number Method 1: Two-Stages-Dialing Outgoing Dial plan Outgoing Dial plan No: 9x | Digit: 3~3 | Des: GW1 IP address No: 8x | Digit:3~3 | Des: GW2 IP address No: 6x | Digit:3~3 | Des :GW1 IP address X: wild card...
  • Page 62 Scenario 5: Gateway 2 to Gateway 1 (Remote Call PSTN number) PLAR connection Call Method: One-Shot-Dialing H.323 Call (Peer-To-Peer Mode) : Remote Call PSTN number Method: One-Shot-Dialing Outgoing Dial plan Outgoing Dial plan No: 8x | Digit: 3~3, Des | GW2 IP address No: 9x | Digit: 3~3 | Des: GW1 IP address Incoming Dial Plan No: 6x | Digit: 3~3 | Des: GW1 IP address...

  • Page 63: H.323 Voip Call: Gatekeeper Mode

    H.323 VoIP Call: Gatekeeper Mode Scenario 7: Gateway 1 to Gateway 2 PLAR connection H.323 Call (GK Mode) Register Number List GW1: 801 GW2: 901 Gateway#2 Gateway#1 Scenario 8: Gateway 2 to Gateway 1 (Call PBX extension number) PLAR connection Call Method: Two-Stages-Dialing H.323 Call (GK Mode) with PBX: Call PBX Extension Method 1: Two-Stage-Dialing...
  • Page 64 Scenario 9: Gateway 2 to Gateway 1 (Remote Call PSTN number with PBX) PLAR connection Call Method: Two-Stages-Dialing H.323 Call (GK Mode) with PBX: Remote Call PSTN number Method 1: Two-Stages-Dialing Register Number List GW1: 801 GW2: 901,609 Gateway#1 Gateway#2 Extension 609 Trunk-Line 02-12345678...
  • Page 65 Scenario 11: Gateway 2 to Gateway 1 (Remote Call PSTN number) PLAR connection Call Method: One-Shot-Dialing H.323 Call (GK Mode) : Remote Call PSTN number Method: One-Shot-Dialing Incoming Dial Plan Register Number List No: 02x | Digit: 3~10 | Strip:2 | FXO port GW1: 801, GW2: 901,609,02x x: wild card Des: Destination IP...

  • Page 66: Sip Voip Call: Peer-To-Peer Mode

    SIP VoIP Call: Peer-To-Peer Mode Scenario 13: Gateway 1 to Gateway 2 PLAR connection SIP Call (Peer-To-Peer Mode) Outgoing Dial plan Outgoing Dial plan No: 8x | Digit: 3~3, Des | GW1 IP address No: 9x | Digit: 3~3, Des | GW1 IP address x: wild card Des: Destination IP Digit: Digit Length min~ max...
  • Page 67 Scenario 15: Gateway 2 to Gateway 1 (Remote Call PSTN number with PBX) PLAR connection Call Method: Two-Stages-Dialing SIP Call (Peer-To-Peer Mode) with PBX: Remote Call PSTN number Method 1: Two-Stages-Dialing Outgoing Dial plan Outgoing Dial plan No: 8x | Digit: 3~3, Des | GW2 IP address No: 9x | Digit: 3~3, Des | GW1 IP address No: 6x | Digit: 3~3, Des | GW1 IP address x: wild card...
  • Page 68 Scenario 17: Gateway 2 to Gateway 1 (Remote Call PSTN number) PLAR connection Call Method: One-Shot-Dialing SIP Call (Peer-To-Peer Mode) : Remote Call PSTN number Method: One-Shot-Dialing Outgoing Dial plan Outgoing Dial plan No: 9x | Digit: 3~3 | Des: GW1 IP address No: 8x | Digit: 3~3, Des | GW2 IP address No: 6x | Digit: 3~3 | Des: GW1 IP address Incoming Dial Plan...

  • Page 69: Sip Voip Call: Sip Proxy Server

    SIP VoIP Call: SIP Proxy Server Scenario 19: Gateway 1 to Gateway 2 PLAR connection SIP Call (Register to SIP Proxy Server Mode) Register Number List GW1: 801 SIP Proxy Server GW2: 901 Gateway#2 Gateway#1 Scenario 20: Gateway 2 to Gateway 1 (Call PBX extension number) PLAR connection Call Method: Two-Stages-Dialing SIP Call (SIP Proxy Server Mode) with PBX: Call PBX Extension Method 1: Two-Stage-Dialing...
  • Page 70 Scenario 21: Gateway 2 to Gateway 1 (Remote Call PSTN number with PBX) PLAR connection Call Method: Two-Stages-Dialing SIP Call (SIP Proxy Server Mode) with PBX: Remote Call PSTN number Method: Two-Stages-Dialing Register Number List GW1: 801 SIP Proxy Server GW2: 901,609 Gateway#1 Gateway#2...
  • Page 71 Scenario 23: Gateway 2 to Gateway 1 (PSTN Call PSTN number) PLAR connection Call Method: Two-Stages-Dialing SIP Call (SIP Proxy Server Mode) : PSTN Call PSTN number Method: Two-Stages-Dialing Register Number List GW1: 801,804 GW2: 901,904 SIP Proxy Server Gateway#1 Gateway#2 02-87654321 04-56785678...

  • Page 72: Faq

    Appendix B Q: What is the default administrator password to login to the gateway? A: By default, your default username is “admin”; default password is “123” to login to the router. For security, you should modify the password to protect your gateway against hacker attacks.

  • Page 73: Faq 1: Firmware Upgrade Requirement And Process

    FAQ 1: Firmware upgrade Requirement and Process 1. Environment Requirement a) A PC with FTP Server (Server-U software) b) A PC or Notebook witch connected to LAN port of gateway. c) Put the image (firmware) named “FW-VIP880_vxxx.bin ” at the assigned folder in FTP Server. For example: “FW-VIP880_v282.bin”...

  • Page 74: Faq 2: Busy Tone Learning

    FAQ 2: Busy Tone Learning STEP 1: Let the FXO port connect to PBX ext. STEP 2: To dial to the FXO port from PBX another ext. STEP 3: Hear dial tone, please dial FXS port number. When FXS port ring, please hang up the phone. STEP 4: At this moment, hear busy tone and also press “y”...

  • Page 75: Faq 3: Fxo Ringer Voltage Threshold / Ringer Voltage Filter Setting

    FAQ 3: FXO Ringer Voltage Threshold / Ringer Voltage Filter Setting VIP-Gateway provides ring detector in FXO device avoiding can not answer and always OFF-HOOK status. This ring detector provides two functions to meet the various PBX’s extension port: 1. FXO ringer voltage threshold 2.
  • Page 76 2. Voice Detection: Voice Detection-based answer supervision is a feature where the Gateway can be configured to “listen” on the line for different tones and voice. The Gateway sends a “connect” signals out or “disconnect” signaling using internet. H.323 scenario description: Loop Start Reverse Battery PSTN line was set polarity reverse a) The gateway can send the “Q.931 connect”...

  • Page 77: Faq 5: Fxo Answer Mode Setting

    Scenario description: Voice Detection based on answer supervision PSTN Line was not support Polarity Reverse: a) The gateway can send the 200 OK SIP signals to Billing system of ITSP, after the user pick up the Phone and detect the voice. b) The gateway can send the 200 BYE SIP signals to Billing system of ITSP, after the user hang up the phone and detect the hang up voice.
  • Page 78 Note: Some ITSP only let the FXO for termination function, they do not user use the FXO port for origination SIP Call Connecting Answer Mode Scenario B description: Hot Line Number” was assigned and the hot line number belongs to SIP device. a) When the call com from PSTN to FXO, FXO start the Hot line dialing to remote SIP gateway b) The phone of remote SIP gateway start ring.
  • Page 79 H.323 Call Connecting Answer Mode Scenario B description: Hot Line Number” was assigned and the hot line number belongs to remote H.323 device. Note: The remote H.323 device need disable the “Auto Answer” a) When the call com from PSTN to FXO, FXO start the Hot line dialing to remote H.323 gateway b) The phone of remote H.323 gateway start ring.

  • Page 80: Faq 6: Peer To Peer Call: Fxo To Fxo

    FAQ 6: Peer to Peer call: FXO to FXO Scenario description: User (500) on site A (VIP-880FO) wishes to have telephone calls to extension (600) on Site B (VIP-880FO B). User (500) on site B (VIP-880FO B) can connect to ser A in the same way. IP address of VIP-880FO_A is: 172.16.0.1 VIP-880FO_A number and dial plan setting: Each port number is 100,200,300,400,500,600,700,800...

  • Page 81: Faq 7: Peer To Peer Call: Fxo To Fxs

    The dial plan of VIP-880FO_B dial plan setting: that means call 0xxx leading number go to IP address 172.16.0.1 gateway (VIP-880FO_A). Usage: The ext.509 dial to ext 501 (connect to FXO port 1) will hear the dial tone, and then dial 0100 go to IP address gateway 172.16.0.2 (VIP-880FO_B), and hear the dial tone again, then dial 609 ext, the ext.609 will ring.
  • Page 82 IP address of VIP-880FO is: 172.16.0.1 VIP-880FO number and dial plan setting: Each port number is 100,200,300,400,500,600,700,800 IP address of VIP-880FS is: 172.16.0.2 VIP-880FS number and dial plan setting: Each port number is 100,200,300,400,500,600,700,800 The dial plan of VIP-880FO dial plan setting: that means call 0xxx leading number go to IP address 172.16.0.2 gateway (VIP-880FS).

  • Page 83: Faq 8: Peer To Peer Call For One Shoot Dialing: Fxo To Fxo

    Usage: The ext.509 dial to ext 501 (connect to FXO) will hear the dial tone, and then dial 0100 go to IP address gateway 172.16.0.2 (VIP-880FS), and phone of port 1(100) will ring. FAQ 8: Peer to Peer call for one shoot dialing: FXO to FXO Scenario description: User (500) on site A (VIP-880FO) wishes to have telephone calls to extension (600) on Site B (VIP-880FO B).
  • Page 84 The dial plan of VIP-880FO_A: that means call 0xxx leading number will go to IP address 172.16.0.2 gateway (VIP-880FO_B). VIP-880FO_B number and dial plan setting: The dial plan of VIP-880FO_B dial plan setting: that means incoming call 60x leading number will hunt port 1 to port 8 The dial plan of VIP-880FO_B: That means call 0xxx leading number will go to IP address 172.16.0.1 gateway (VIP-880FO_A).

  • Page 85: Faq 9: Peer To Peer Call: Hotline Setting

    FAQ 9: Peer to Peer call: Hotline setting Hot line Basic Concept: Any number set in Hot line field will be dialed by VoIP call automatically. For FXS port case: When user picks up the phone, the gateway will dial the hot line number to internet by VoIP call.
  • Page 86 Scenario description: Register to SIP proxy server/H.323 Gatekeeper direct call STEP 1: Let your VIP-GW register to SIP proxy or H.323 Gatekeeper server STEP 2: To set hot line number in Hot Line Option STEP 3: When users pick up the phone (port1), the gateway will dial the “911” to SIP proxy or H.323 Gatekeeper server (ITSP) Scenario description: Register to SIP Proxy / H.323 Gatekeeper server and Peer to Peer direct call first...

  • Page 87: Faq 10: Sip Speed Call Setting

    STEP 4: When users pick up the phone (port 1), the gateway will dial the “911” to the gateway which’s IP address 172.16.0.119. Note: This call will not call to SIP Proxy or H.323 Gatekeeper server because of direct call first. FAQ 10: SIP speed call setting Speed calls Concept: Cut your phone number down to fewer digit dialing!
  • Page 88 Scenario description C: User wants to dial 888 instead of 810-861234567890 Note: The destination IP address is the domain name of sip proxy server...

  • Page 89: Appendix C

    Appendix C VIP-281 series Specifications Product 2-Port H.323/SIP VoIP Gateway Model VIP-281 VIP-281FS Hardware 1 x 10/100Mbps RJ-45 port 4 x 10/100Mbps RJ-45 port Voice 2 x RJ-11 connection 2 x RJ-11 connection ( 1 x FXS, 1 x FXO)

  • Page 90: Vip-480 Series Specifications

    VIP-480 series Specifications Product 4-Port H.323/SIP VoIP Gateway Model VIP-480 VIP-480FS VIP-480FO VIP-480FD Hardware 1 x 10/100Mbps RJ-45 port 4 x 10/100Mbps RJ-45 port Voice 4 x RJ-11 4 x RJ-11 4 x RJ-11 4 x RJ-11 connection connection connection connection ( 2 x FXS, 2 x FXO) ( 4 x FXO with...

  • Page 91: Vip-880 Series Specifications

    VIP-880 series Specifications Product 8-Port H.323/SIP VoIP Gateway Model VIP-880 VIP-880FO Hardware 1 x 10/100Mbps RJ-45 port 1 x 10/100Mbps RJ-45 port Voice 8 x RJ-11 connection 8 x RJ-11 connection ( 4 x FXS, 4 x FXO) ( 8 x FXO) Protocols and Standard Standard H.323 v2/v3/v4 and SIP (RFC 3261) , SDP (RFC 2327), Symmetric RTP,...

  • Page 92: Vip-1680 Series Specifications

    VIP-1680 series Specifications Product 16-Port H.323/SIP VoIP Gateway Model VIP-1680 VIP-1680FS VIP-1680FO VIP-1680FD Hardware 1 x 10/100Mbps RJ-45 port 1 x 10/100Mbps RJ-45 port Voice 1 x RJ-21 1 x RJ-21 1 x RJ-21 connector for connector for connector for 16 x RJ-11 connecting to connecting to...

  • Page 93: Vip-2480 Series Specifications

    VIP-2480 series Specifications Product 24-Port H.323/SIP VoIP Gateway Model VIP-2480 VIP-2480FS VIP-2480FO VIP-2480FD Hardware 1 x 10/100Mbps RJ-45 port 1 x 10/100Mbps RJ-45 port Voice 1 x RJ-21 1 x RJ-21 1 x RJ-21 connector for connector for connector for 24 x RJ-11 connecting to connecting to...

This manual is also suitable for:

Vip-880Vip-480Vip-2480Vip-1680Vip-281fsVip-480fs ... Show all

Table of Contents