Page 3
Understanding Mounting and Installer’ s Choice® Hunter’s patented 3-position mounting system provides you maximum installation flexibility and ease. You can install your Hunter fan in one of three ways, depending on ceiling height and your preference: Low Profile, Standard, or Angle mounting. e steps in this manual include instructions for all three Installer’s Choice mounting methods.
• Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician. Gathering the Tools You will need the following tools for installing the fan: •...
Tighten the screws into the 9/64” pilot holes; do not use lubricants on the screws. Do not over tighten. Flat Washer 42501-01 • 10/24/05 42501 Sunset Boulevard.indd 2 • Installing the Ceiling Plate Ceiling Plate Steps 2-3 –...
3-5. Raise the fan and place the hook on the ceiling plate through the U-shaped hole in the rim. Go to 4 • Wiring the Fan. WARNING: Fan may fall if not assembled as directed in these installation instructions. 10/24/2005, 11:04 AM Step 3-5 U-shaped Hole 42501-01 • 10/24/05...
CAUTION: Be sure no bare wire or wire strands are visible after making connections. 4-4. Push all wires and wire nuts back through the ceiling plate hole into the outlet box. 42501-01 • 10/24/05 42501 Sunset Boulevard.indd 4 • Wiring the Fan Step 4-3...
Locate the tab indicators, small bumps on top of tabs. Press firmly on opposite sides of the ring towards the canopy. e tabs will flex out releasing the trim ring from the canopy. Canopy Screw 10/24/2005, 11:04 AM 42501-01 • 10/24/05...
6-4. For each blade, insert one blade armature screw through the blade iron, and attach loosely to the fan. Insert the second blade armature screw, then securely tighten both armature screws. 42501-01 • 10/24/05 42501 Sunset Boulevard.indd 6 • Assembling the Blades Steps 6-1 –...
7-4. Turn the housing counterclockwise until the housing assembly screws are firmly situated in the narrow end of the keyhole slots. Install the remaining #6-32 x 3/8” screw into the housing. Tighten all three screws firmly. 10/24/2005, 11:05 AM 42501-01 • 10/24/05...
8-2. Install the included 12-volt battery into the transmitter. CAUTION: e remote control device complies with part 15 of the FCC rules. Changes or modifications not expressly approved by Hunter Fan Company could void your authority to operate this equipment.
9-2. Place the lower switch housing assembly over the upper switch housing. Align the side screw holes in the upper and lower switch housings. Attach the lower switch housing to the upper switch housing with three #6-32 x 1/2” housing assembly screws. 10/24/2005, 11:05 AM 42501-01 • 10/24/05...
10-6. You can mount the remote holder to any toggle switch plate with the screws already in the switch plate. Or, you can simply mount the remote holder on the wall. Step 10-5 42501-01 • 10/24/05 42501 Sunset Boulevard.indd Fan Reverse Fan Speed...
11-4. Clean wood finish blades with a furniture polishing cloth. Occasionally, apply a light coat of furniture polish for added protection and beauty. Clean painted and high-gloss blades in the same manner as the fan finish. 10/24/2005, 11:06 AM 42501-01 • 10/24/05...
2. Tighten all blade iron screws. 3. Turn power off, support fan very carefully, and check that the hanger ball is properly seated. 42501-01 • 10/24/05 42501 Sunset Boulevard.indd 12 • Troubleshooting If you need parts or service assistance, please call 888-830-1326 or visit us at our Web site at http://www.hunterfan.com.