Page 1
Keep this insert for future reference. aside from the information contained in this update, all other content in the owner's manual applies to this machine.
Page 5
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemi- cals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. •...
8. USE RIGHT TOOL. Do not force tool or damp or wet locations, or where any flam- attachment to do a job for which it was not mable or noxious fumes may exist. Keep designed. work area well lighted. H3390 Wet Tile Saw...
ING DIFFICULTIES performing the intend- ed operation, stop using the machine! Then 13. NEVER OVERREACH. Keep proper foot- contact our service department or ask a ing and balance at all times. qualified expert how the operation should be performed. H3390 Wet Tile Saw...
9. Dust Mask. Always wear a dust mask 17. Side Grinding. Never grind tile on the side when cutting tile. of the blade, or make radius or curve cuts. 10. Diamond Blades. Diamond blades DO NOT cut material, rather they grind materi- H3390 Wet Tile Saw...
We are proud to offer the Grizzly Model H3390 Grizzly Industrial, Inc. Wet Tile Saw. The Model H3390 is part of a 1203 Lycoming Mall Circle growing Grizzly family of fine woodworking Muncy, PA 17756 machinery.
If frequent circuit failures occur when The Model H3390 is wired to operate at 110V. A using this machine, contact our Service Ground Fault Circuit Interrupter (GFCI) must be Department or your local electrical contractor.
It is your responsibility to make sure dance with all local codes and ordinances. your electrical systems comply with all local electrical codes and ordinances. Operating this machine when it is not properly grounded can result in electric shock or electro- cution. H3390 Wet Tile Saw...
Unpainted surfaces may be coated with a waxy Floor Load oil to protect them from corrosion during ship- The Model H3390 is a medium load with a medi- ment. Remove this waxy oil with a solvent clean- um footprint. Most commercial or home shop er or citrus-based degreaser such as Grizzly’s...
G. Power Switch H. Water Pump Plug-In I. V-Belt Cover J. Rip Fence K. Table L. 45˚ Bevel Miter Fence M. Saw Blade N. Circuit Reset Button Figure 2. Right side of saw. O. Blade Height Adjustment Knob H3390 Wet Tile Saw...
The assembly of the Model H3390 Wet Tile Saw Assembly is straightforward and can be completed in a rela- tively short period of time. To assemble the saw: Keep clothing rolled up Assemble the two stand brackets using (2) and out of the way of M8-1.25 x 50 hex bolts and (2) M8-1.25 lock...
Page 16
Figure 8 . Slide the pivot shaft into the mounting holes on the motor assembly and secure with the blade height adjustment knob as shown in Figure 9 . Figure 10. Mounting the motor assembly. H3390 Wet Tile Saw -11-...
With the arbor lock pin still fully depressed, tighten the arbor nut using an open-end wrench. Reposition the blade guard to the down posi- tion and tighten the knob loosened in Step 1. H3390 Wet Tile Saw -13-...
Page 12. Make sure all tools or foreign objects have been removed from the machine. Review Section 3: Circuit Requirements beginning on Page 6 and make sure all wiring is correct. -14- H3390 Wet Tile Saw...
Figure 19. Filled water reservoir. The pump turns on when the saw is turned on. The water flow can be adjusted using the flow rate lever on the side of the pump. H3390 Wet Tile Saw -15-...
Slow down the feed rate immediately. If the saw shuts off unexpectedly, stop cutting the tile and turn the power switch off. Wait 15 minutes and press the circuit reset button. -16- H3390 Wet Tile Saw...
(See Figure 21 ) and adjusting the table. Cap Screw (1 of 2) Figure 22. Bevel cutting a tile edge. Figure 21. Table fine-tuning cap screw. H3390 Wet Tile Saw -17-...
SECTION 6: MAINTENANCE General Regular periodic maintenance on your Model Disconnect power to the H3390 will ensure its optimum performance. machine when perform- Make a habit of inspecting your machine each ing any maintenance on time you use it. the table saw. Failure to...
Trade safety rules should be considered as they apply to journals, woodworking magazines, and your local your specific situation. library are good places to start. H3390 Wet Tile Saw -19-...
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
___Woodwright’s Shop What machines/supplies would you like Grizzly Industrial to carry? ___Other__________________________________________________ __________________________________________________________ What is your annual household income? __________________________________________________________ ___$20,000-$29,999 ___$60,000-$69,999 What new accessories would you like Grizzly Industrial to carry? ___$30,000-$39,999 ___$70,000-$79,999 __________________________________________________________ ___$40,000-$49,999 ___$80,000-$89,999 ___$50,000-$59,999 ___$90,000 +...
Page 33
FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 FOLD ALONG DOTTED LINE Send a Grizzly Catalog to a friend: Name_______________________________ Street_______________________________ City______________State______Zip______ TAPE ALONG EDGES--PLEASE DO NOT STAPLE...
Page 35
Buy Direct and Save with Grizzly – Trusted, Proven and a Great Value! ® Visit Our Website Today And Discover Why Grizzly Is The Industry Leader! ® • SECURE ORDERING • ORDERS SHIPPED WITHIN 24 HOURS • E-MAIL RESPONSE WITHIN ONE HOUR -OR- FREE Call Today For A...