Table of Contents
Advertisement
Quick Links
For Your Records and Warranty
Assistance
Model Name: _____________________
Catalog/Model No.: ________________
Serial No.: _______________________
Date Purchased: ___________________
Where Purchased: _________________
For reference also attach your receipt or a
copy of your receipt to the manual.
42616-01 • 02/20/06
42616-01 rev 02-14-06.indd
1
2/20/2006, 3:15 PM
Advertisement
Table of Contents
Related Manuals for Hunter 42616-01
Summary of Contents for Hunter 42616-01
- Page 1 Assistance Model Name: _____________________ Catalog/Model No.: ________________ Serial No.: _______________________ Date Purchased: ___________________ Where Purchased: _________________ For reference also attach your receipt or a copy of your receipt to the manual. 42616-01 • 02/20/06 42616-01 rev 02-14-06.indd 2/20/2006, 3:15 PM...
-
Page 2: Table Of Contents
• Read this entire manual carefully before beginning installation. Save these instructions. • Use only Hunter replacement parts. • To reduce the risk of personal injury, attach the fan directly to the support structure of the building according to these instructions, and use only the hardware supplied. - Page 3 Understanding Mounting and Installer’ s Choice® Hunter’s patented 3-position mounting system provides you maximum installation flexibility and ease. You can install your Hunter fan in one of three ways, depending on ceiling height and your preference: Low Profile, Standard, or Angle mounting. e steps in this manual include instructions for all three Installer’s Choice mounting methods.
-
Page 4: Getting Ready
• Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician. Gathering the Tools You will need the following tools for installing the fan: •... -
Page 5: Installing The Ceiling Plate
For Angled Ceilings: Be sure to orient the ceiling plate so that the two tabs are pointing towards the ceiling peak. 2-2. Your fan comes with four preinstalled noise isolators. Check to make sure all four isolators are in place and were not removed during shipment. -
Page 6: Assembling The Fan
3-1. Unbundle the wires from the fan. For Standard or Angle mounting: 3-2. Insert the downrod through the canopy and canopy trim ring. Feed the wires from the fan through the downrod on one side of the pin in the ball. Canopy 3-3. -
Page 7: Setting The Remote Transmitter And Receiver
4-2. Install the included 9-volt battery into the transmitter. CAUTION: e remote control device complies with part 15 of the FCC rules. Changes or modifications not expressly approved by Hunter Fan Company could void your authority to operate this equipment. -
Page 8: Wiring The Fan
• e black/white wire from the fan to the red wire from the receiver (marked on white tag “LIGHT OUT”) • e black wire from the fan to the black wire from the receiver (marked on white tag “FAN OUT”) •... -
Page 9: Installing The Canopy And Canopy Trim Ring
Note: Your fan may have multiple tabs and grooves that must be aligned. 6-2. Swing the fan up to align the canopy screw holes with the mounting holes on the ceiling plate. WARNING: e slots in the canopy must remain engaged while swinging the canopy for alignment. -
Page 10: Assembling The Blades
7 • Assembling the Blades Hunter fans use several styles of fan blade irons (brackets that hold the blade to the fan). 7-1. Your fan may include blade grommets. If your fan has grommets, insert them by hand into the holes on the blades. -
Page 11: Completing Your Installation With Or Without A Light Fixture
Housing 42616-01 • 02/20/06 42616-01 rev 02-14-06.indd Your Hunter fan comes with a switch housing assembly and an optional light fixture. is feature gives you the option of installing the fan with OR without the included light fixture. e steps below direct you whether or not you are installing a light fixture. - Page 12 8-12. Install the lower switch housing to the upper switch housing. 8-13. Install glass shades and candelabra bulbs (sold separately). Housing Assembly Screw Hunter Fan Company 42616-01 rev 02-14-06.indd Switch Housing Assembly Screw Steps 8-10 - 8-12 2/20/2006, 3:17 PM...
-
Page 13: Operating The Remote Control And Mounting The Holder
9-1. e remote has individual buttons for setting fan speed and light intensity. Refer to the figure on the right. Note: For best operation, start the fan by pressing high, then select your desired speed. 9-2. e light button turns the light on to full brightness. To dim the light, hold the light button until you reach your desired brightness. -
Page 14: Operating And Cleaning Your Ceiling Fan
10-2. Ceiling fans work best by blowing air downward (counterclockwise blade rotation) in warm weather to cool the room with a direct breeze. In cold weather, having the fan draw air upward (clockwise blade rotation) will distribute the warmer air trapped at the ceiling around the room without causing a draft. -
Page 15: Troubleshooting
6. Check and tighten the screws in the switch housing mounting plate and in the upper and lower switch housing. Problem: Excessive wobbling. 1. If your fan wobbles when operating, use the enclosed balancing kit and instructions to balance the fan. 2. Tighten all blade and/or blade iron screws.