Table of Contents
Advertisement
Quick Links
For Your Records and
Warranty Assistance
For reference, also attach your receipt or a copy
of your receipt to the manual.
__________________________________________
Model Name
__________________________________________
Model No.
__________________________________________
Date Purchased
__________________________________________
Where Purchased
Form# 42696-01
20091104
©2009 Hunter Fan Co.
Type T Models
Type T Models
Type T Models
Owner's Guide and Installation Manual
Advertisement
Table of Contents
Related Manuals for Hunter 42696-01
Summary of Contents for Hunter 42696-01
- Page 1 For reference, also attach your receipt or a copy of your receipt to the manual. __________________________________________ Model Name __________________________________________ Model No. __________________________________________ Date Purchased __________________________________________ Where Purchased Form# 42696-01 20091104 ©2009 Hunter Fan Co. Type T Models Type T Models Type T Models Owner’s Guide and Installation Manual...
-
Page 2: Table Of Contents
Table Of Contents Preparing the Fan Site . . . . . . . . . . . . . . . . . 3 1 •... -
Page 3: Preparing The Fan Site
If you want to use an existing fan site, complete the following checklist to determine if the site is acceptable and safe for your new Hunter fan. If you cannot check off every item, prepare a new fan site as described on this page. - Page 4 3-1. Attach a 2” x 4” support brace between two joists. Position it to allow you to recess the bottom of the outlet box a minimum of 1/16” into the ceiling. 3-2. Check the support brace to ensure it will support the full weight of the fan and light kit.
- Page 5 Understanding Mounting and Installer’ s Choice® Hunter’s patented 3-position mounting system provides you maximum installation flexibility and ease. You can install your Hunter fan in one of three ways, depending on ceiling height and your preference: Low Profile, Standard, or Angled mounting. The steps in this manual include instructions for all three Installer’s Choice mounting methods.
-
Page 6: Getting Ready
• Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician. Gathering the Tools You will need the following tools for installing the fan: •... -
Page 7: Installing The Ceiling Plate
Tighten the screws into the 9/64” pilot holes; do not use lubricants on the screws. Do not over tighten. Flat Washer 42696-01 • 11/04/09 • Hunter Fan Company For Angled Ceilings: Be sure to orient the ceiling plate so that the two tabs are pointing toward the ceiling peak. -
Page 8: Assembling And Hanging The Fan
Note: To hang the fan, you must tilt the canopy to an almost vertical position so that the canopy slots sit on the ceiling plate hooks. 3-7. Raise the fan and align the slots in the canopy with the hooks on the ceiling plate. -
Page 9: Wiring The Fan
4-3. Connect the bare or green ground wire (grounding) from the ceiling to the green ground wire (grounding) from the ceiling plate and the green ground wire from the fan or the green ground wire present on the low profile washer. -
Page 10: Installing The Canopy And Canopy
Note: Your fan may have multiple tabs and grooves that must be aligned. 5-2. Swing the fan up to align the canopy screw holes with the mounting holes on the ceiling plate. WARNING: The slots in the canopy must remain engaged while swinging the canopy for alignment. -
Page 11: Assembling The Blades
Hunter fans use several styles of fan blade irons (brackets that hold the blade to the fan). 6-1. Your fan may include blade grommets. If your fan has grommets, insert them by hand into the holes on the blades. 6-2. Attach each blade to a blade iron using three blade assembly screws. -
Page 12: Installing The Switch Housing
Align the side screw holes in the upper and lower switch housings. Attach the lower switch housing to the upper switch housing with three housing assembly screws. Note: You can customize your Hunter fan with a number of accessory light kits. Housing... -
Page 13: Operating And Cleaning Your
8 • Operating and Cleaning Your Ceiling Fan 8-1. Turn on electrical power to the fan. 8-2. The fan pull chain controls power to the fan. The pull chain has four settings in sequence: High, Medium, Low, and Off. • Pull the chain slowly to change settings. -
Page 14: Troubleshooting
2. Tighten all blade iron screws. 3. Turn power off, support fan very carefully, and check that the hanger ball is properly seated. 42696-01 • 11/04/09 • Hunter Fan Company 9 • Troubleshooting If you need parts or service assistance, please call...