Table of Contents
Advertisement
Quick Links
For Your Records and Warranty
Assistance
Model Name: _____________________
Catalog/Model No.: ________________
Serial No.: _______________________
Date Purchased: ___________________
Where Purchased: _________________
For reference also attach your receipt or a
copy of your receipt to the manual.
42606-01 • 11/18/05
Advertisement
Table of Contents
Related Manuals for Hunter 42606-01
Summary of Contents for Hunter 42606-01
- Page 1 For Your Records and Warranty Assistance Model Name: _____________________ Catalog/Model No.: ________________ Serial No.: _______________________ Date Purchased: ___________________ Where Purchased: _________________ For reference also attach your receipt or a copy of your receipt to the manual. 42606-01 • 11/18/05...
-
Page 2: Table Of Contents
• Read this entire manual carefully before beginning installation. Save these instructions. • Use only Hunter replacement parts. • To reduce the risk of personal injury, attach the fan directly to the support structure of the building according to these instructions, and use only the hardware supplied. - Page 3 Understanding Mounting and Installer’ s Choice® Hunter’s patented 3-position mounting system provides you maximum installation fl exibility and ease. You can install your Hunter fan in one of three ways, depending on ceiling height and your preference: Low Profi le, Standard, or Angle mounting. e steps in this manual include instructions for all three Installer’s Choice mounting methods.
-
Page 4: Getting Ready
• Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician. Gathering the Tools You will need the following tools for installing the fan: •... -
Page 5: Installing The Ceiling Plate
For Angled Ceilings: Be sure to orient the ceiling plate so that the two tabs are pointing towards the ceiling peak. 2-2. Your fan comes with four preinstalled noise isolators. Check to make sure all four isolators are in place and were not removed during shipment. -
Page 6: Assembling The Fan
For Standard or Angle mounting: 3-2. Insert the downrod through the canopy and canopy trim ring. Feed the wires from the fan through the downrod on one side of the pin in the ball. 3-3. Loosen the square head set screw on the adapter to install the pipe and ball assembly. -
Page 7: Hanging And Wiring The Fan
4-1. Raise the fan and align the slots in the canopy with the hooks on the ceiling plate. Note: To hang the fan, you must tilt the canopy to an almost vertical position so that the canopy slots sit on the ceiling plate hooks. -
Page 8: Installing The Canopy And Canopy Trim Ring
Note: Your fan may have multiple tabs and grooves that must be aligned. 5-2. Swing the fan up to align the canopy screw holes with the mounting holes on the ceiling plate. WARNING: e slots in the canopy must remain engaged while swinging the canopy for alignment. -
Page 9: Assembling The Blades
Hunter fans use several styles of fan blade irons (brackets that hold the blade to the fan). 6-1. Your fan may include blade grommets. If your fan has grommets, insert them by hand into the holes on the blades. 6-2. Attach each blade to a blade iron using three blade assembly screws. -
Page 10: Completing Your Installation With Or Without A Light Fixture
Screw Housing Hunter Fan Company Your Hunter fan comes with a switch housing assembly and an optional light fixture. is feature gives you the option of installing the fan with OR without the included light fixture. e steps below direct you whether or not you are installing a light fixture. - Page 11 CAUTION: Be sure no bare wire or wire strands are visible after making connections. Light Fixture Mounting Screws 42606-01 • 11/18/05 Switch Housing Washer Light Fixture Assembly...
- Page 12 7-12. Install one medium base incandescent light bulb (100 Watt maximum). 7-13. Insert the globe into the fixture. Install and tighten the thumbscrews manually. Do not overtighten. Note: If thumbscrews are pre-threaded, loosen the screws before inserting the globe, then retighten securely. 42606-01 • 11/18/05...
-
Page 13: Operating And Cleaning Your Ceiling Fan
8-1. Turn on electrical power to the fan. 8-2. e fan pull chain controls power to the fan. e pull chain has four settings in sequence: High, Medium, Low and Off . • Pull the chain slowly to change settings. -
Page 14: Troubleshooting
2. Tighten all blade and/or blade iron screws. 3. Turn power off , support fan very carefully, and check that the hanger ball is properly seated. If you need parts or service assistance, please call 888-830-1326 or visit us at our Web site at http://www.hunterfan.com.