Advertisement
Installing on a desk or tabletop
2. Turn the telephone base over and position it with the power jack
and telephone line jack facing towards you.
Telephone jack requirements
3. Press on the convertible base mount indicated by arrows below to
To use this phone, you need a RJ11C type modular
Wall plate
remove it from the telephone base.
telephone jack, which might look like the one
pictured here, installed in your home. If you do not
have a modular jack, call your telephone service
provider to find out how to have one installed.
Modular
telephone
If you have DSL high speed Internet service, a DSL
line jack
filter is required (not included). Contact your DSL
service provider for more information about DSL
filters.
NOTE: Refer to your 30542 user's guide for wall mounting instructions.
1. Make sure the wall mounting tab is in DESK position. Use a coin or
small flat tool to rotate it if needed.
4. Plug one end of the coiled cord into the jack on the bottom of the
telephone base and the other end into the jack at the bottom of the
corded handset.
5
5. Replace the convertible base mount by aligning the small tabs to
the slots in the middle of the telephone base and the larger tabs in
the slots near the top as shown..
THIS END UP
FOR WALL USE
6. Turn the set over and place the handset on the cradle. Plug one end
of the telephone line cord into the jack on the back of the telephone
base and the other end into a modular jack.
7. Plug the smaller end of the power adapter into the jack on the back
of the telephone base and the larger end into an electrical outlet
not controlled by a wall switch.
Route the
cord through
the tabbed
slot.
DESK
DESK
Route the cord through
the tabbed slot.
6
CAUTION:
1. Use only the power adapter that came with this unit. Using other power
adapters may damage the unit.
2. To prevent fire or electrical shock hazard, do not expose this product to rain or
moisture.
Charger installation (For models with additional handsets)
1. Plug the smaller end of the power adapter into the charger.
DESK
DESK
THIS END UP
FOR WALL USE
2. Plug the larger end of the power adapter into an electrical outlet
not controlled by a wall switch.
DSL filter (not included) is
required if you have DSL
high speed Internet service.
7
8
Battery installation
Initial settings
Date and time
Please fully charge your handset before use!
In order for your answering system to accurately mark your messages,
For optimum battery performance, charge the battery for 16 hours before first
you must set the time and date.
use.
Using a cordless handset
1. Press
2. Press
red
black
wire
press
wire
3. Press
4. Enter the current month, day and year. For example,
May 16, 2010 should be entered as [0], [5], [1], [6], [1],
[0].
1. Plug the battery connector
2. Place the
3. Align the
securely into the socket inside the
battery and
cover against
5. Press
handset battery compartment.
the wire inside
the battery
6. Enter the current hour and minute. For example, 9:30
Make sure that red and black wires
the battery
compartment
should be entered as [0], [9], [3], [0]. Press
on the plug are properly inserted
compartment.
and slide it
to select AM or PM and then press
into the socket as shown.
upwards until it
clicks into place.
Using the telephone base
Animated
1. Press
charging
indicator
2. Press
and then press
4. Place the handset onto the charger as shown. An
3. Press
animated battery icon will display after a few minutes
to show that the handset battery is successfully being
4. Enter the current month, day and year. For
charged. For optimum performance, please allow the
example, May 16, 2010 should be entered as [0],
battery to charge for 16 hours before first use.
[5], [1], [6], [1], [0].
5. Press
6. Enter the current hour and minute. For example,
CAUTION:
9:30 should be entered as [0], [9], [3], [0]. Press
1. Use only the supplied rechargeable battery or equivalent replacement battery.
/
See battery specifications on the Technical specification page in your 30524
user's guide or visit our website at www.gephones.com to find out how to order
to confirm.
a replacement battery if necessary.
Please refer to your 30524 user's guide for complete
2. If the handset will not be used for an extended period of time, unplug the battery
and remove it from the handset to prevent possible leakage.
telephone settings.
9
when in idle mode.
10:30
11/20
or
to select CLOCK & ALARM and then
PM
CLOCK & ALARM
.
>SET DATE/TIME
again to select SET DATE/TIME.
10:30
11/20
PM
SET DATE
05/16/10
to confirm.
10:30
11/20
PM
SET TIME
or
09:30 PM
to confirm.
when in idle mode.
/
to select CLOCK & ALARM
10:30
.
11/20
PM
CLOCK & ALARM
again to select SET DATE/TIME.
>SET DATE/TIME
10:30
11/20
PM
SET DATE
05/16/10
to confirm.
10:30
11/20
PM
SET TIME
to select AM or PM and then press
09:30 PM
10
Advertisement
