Vent System Identification - White Mountain Hearth DVX36FP32CL(N,P)-1 Installation Instructions And Owner's Manual

Installing Vent Components (Figure 46)
Begin the vent system installation by installing the first Simpson Duravent
component, 90° elbow to the starting collars or straight pipe on the top of
the appliance, then the straight pipe length and then horizontal or vertical
termination kit.
NOTE: All outer connection joints must be sealed with aluminum
tape, screws or silicone sealant rated above 300°F/149°C. The inner
flue joints do not require any sealant.
Simpson Duravent vent system components lock into place by sliding the
concentric pipe section with four (4) equally spaced interior beads onto
the appliance collar or previously installed component end with four (4)
equally spaced indented sections. When the internal beads of each starting
outer pipe line up, rotate pipe section clockwise 90° (approximately 3
inches). The vent pipe is now locked together.
Continue adding components per the pre-planned vent system configuration.
Be certain that each succeeding vent component is securely fitted and
locked into the preceding component in the vent system.
Special Venting Components
Simpson Dura-Vent can be used when using DVA47 Adaptor vertically off top
of fireplace only.
Can be purchased from Simpson Duravent, Dealer, or from Empire Comfort
Part Number Description
SD-908 6" Pipe Length
SD-907 9" Pipe Length
SD-906 12" Pipe Length
SD-904 24" Pipe Length
SD-903 36" Pipe Length
SD-902 48" Pipe Length
SD-911 Adjustable Pipe Length 11 - 14 5/8"
SD-985 Horizontal Square Termination Cap
SD-950 Vinyl Siding Standoff
SD-945 45° Elbow
SD-990 90° Elbow
SD-947 Wall Firestop
SD-963 Ceiling Firestop
SD-942 Wall Thimble
SD-943 Roof Flashing - 0/12 to 6/12 Roof Pitch
SD-953 Storm Collar
SD-991 High Wind Vertical Top
SD-981 36" Snorkel
SD-982 14" Firestop Snorkel
SD-988 Wall Strap
Special DV Vent Kits - Simpson Duravent and Empire Comfort Systems, Inc.
Can be purchased from Empire Comfort Systems, Inc.
DVVK-4V Direct-Vent Fireplace Vent Kit - Vertical, Includes SD-991,
SD-953, and SD-943
DVVK-4T Direct-Vent Fireplace Vent Kit for Top Vent, Thru-the-wall, 8
to 11 inch wall thickness, Includes SD-911, SD-985, SD-990
and SD-942
DVVK-4TS Direct-Vent Fireplace Vent Kit for Top Vent, Thru-the-wall,
5 to 7 inch wall thickness, Includes SD908, SD-985, SD-990
and SD-942
DVVK-4FV Direct-Vent Fireplace Vertical Flex Vent Kit
23835-1-0607
VENT SYSTEM IDENTIFICATION
Systems, Inc.
90° ELBOW
OR
45° ELBOW
90° ELBOW
CEILING FIRESTOP
WALL STRAP
PIPE LENGTH
Special Venting Components
Can be purchased from Simpson Duravent or from Empire Comfort Systems,
Part Number Description
SD-1208 6" Pipe Length
SD-1207 9" Pipe Length
SD-1206 12" Pipe Length
SD-1204 24" Pipe Length
SD-1203 36" Pipe Length
SD-1202 48" Pipe Length
SD-1211 Adjustable Pipe Length 11 - 14 5/8"
SD-1284 Horizontal Square Termination Cap
SD-1250 Vinyl Siding Standoff
SD-1245 45° Elbow
SD-1290 90° Elbow
SD-1249 Wall Firestop
SD-1263 Ceiling Firestop
SD-1243 Roof Flashing - 0/12 to 6/12 Roof Pitch
SD-1253 Storm Collar
SD-1291 High Wind Vertical Top
SD-1281 36" Snorkel
SD-1282 14" Firestop Snorkel
SD-1247 Wall Thimble Firestop
Special DV Vent Kits - Simpson Duravent and Empire Comfort Systems, Inc.
Can be purchased from Empire Comfort Systems, Inc.
DVVK-5R Direct-Vent Fireplace Vent Kit for Rear Vent, 6 to 12 inch
wall thickness, Includes SD-1208, SD-1247, and SD-2184
DVVK-5T
Direct-Vent Fireplace Vent Kit for Top Vent, Thru-the-wall,
4 to 6 inch wall thickness, Includes SD-1290, SD-1284, SD-
1208 and SD-1247
DVVK-5V
Direct Vent Fireplace Vent Kit - Vertical, Includes SD-1291,
SD-1253, and SD-1243
DVVK-5TS
Top Vent Kit (Horz.) - 4½" to 6" wall thickness (114.3mm
to 152mm)
DVVK-5F Horizontal Flex Vent Kit (4' Flex) (1.22m)
WALL THIMBLE
VERTICAL
TERMINATION
(MAXIMUM OF
THREE 90° ELBOWS)
HORIZONTAL
TERMINATION
(MAXIMUM OF
TWO 90° ELBOWS)
Figure 46
Simpson Dura-Vent
Inc.
STORM COLLAR
ROOF FLASHING
Page 31