Table of Contents
Advertisement
Continued from page 7 ...
Programming codes from an LCD Keypad:
Master Code
Press the [ ] key to enter the function list. Scroll (< >) to...
Press (*) for <>
Press [5] or [ ]. The display will read...
Access Codes
Enter Master
Enter your current Master Code. The display will read...
Access Code
(*) to Edit
<>
"40P" represents the Master Code. Press the [ ] key to indicate that you wish to
User Code
40P
program the Master Code. The display will read...
Enter New Code
Enter the new Master Code. The Master Code must be four digits long, unless
1234
<>
otherwise indicated by your installer. Enter digits 0 through 9 only. Once the new
code is entered, the keypad will beep 3 times and the display will read...
(*) to Edit
<>
Press [#] to exit the code programming function.
User Code
40P
Be sure to record your new Master Code on the "System Information" page in this booklet.
NOTE: We recommend that the factory default Master Code [1234] not be used.
Additional Access Codes
To erase, add or change a user code, press [ ] to enter the function list. Use the arrow (< >) keys to
scroll to the following message...
Press [ ]. Display will read...
Press (*) for <>
Access Codes
Enter the Master Code. Display will read...
Enter Master
Access Code
[*] to Edit
<>
Use the scroll keys (< >) to find the access code – indicated by "02P" to "32P" –
User Code
01P
you wish to add, change or delete. Press the [ ] key to select the code you wish to
change. The display will read...
To add or change a code, enter the new code. Access codes must be four digits
Enter New Code
1234
<>
unless otherwise indicated by your installer. Enter digits 0 through 9 only. To delete
an access code, enter [ ]. Once the 4-digit code or [ ] has been entered, the
keypad sounder will beep 3 times and the display will read...
The "P" means the code has been programmed. If there is no "P" then that code is
[*] to Edit
<>
User Code
01P
deleted. Press [#] to exit the code programming function. The Master code cannot be
erased.
Remember to record your new code(s) on the "System Information" page in this booklet.
Access Code Attributes
Additional programmable attributes, such as zone bypassing capability, can be activated or deactivated
for each access code. For more information regarding access code attributes, please contact your
installer.
10
If an Alarm Sounds
Fire Alarm
If your system has been installed with fire detectors and the alarm sounds in a pulsing mode, follow
your emergency evacuation plan immediately (see "Fire Escape Planning" on page 15).
Intrusion Alarm
If an intrusion alarm sounds, indicated by a continuous Bell or Siren, the alarm may be silenced by
entering your access code. If the alarm was unintentional, call local authorities immediately to avoid an
unnecessary response.
You can determine the source of the alarm by following the instructions in the "Disarming" section (see
page 6). Once the source of the alarm has been corrected, the panel can be restored to its original
Armed state.
NOTE: A fire alarm has priority over a burglary type alarm.
Function Keys
(Not available on the PC1555RKZ)
The keypads have five function keys – marked Stay, Away, Chime, Reset and Exit – which allow easy
single-button activation of the most commonly used features. If your installer has enabled these keys, you can
execute their programmed function by pressing and holding the corresponding key for two seconds.
For information regarding the operation of the function keys, talk to your alarm installer.
Programming Security Codes
Programming codes from an LED or Fixed Message LCD5501Z keypad:
The Master Code
To program the Master Code, enter [ ][5][current Master Code][40][new Master Code]. The Master
Code must be four digits long, unless otherwise indicated by your installer. Enter digits 0 through 9
only. Press [#] to return to the Ready state.
NOTE: You must program all digits in each access code.
Be sure to record your new Master Code on the "System Information" page in this booklet. NOTE: We
recommend that the factory default or obvious codes such as [1111] or [1234] not be used.
Additional Codes
Up to 32 additional access codes (01 through 32) may be programmed.
To program a new code:
Enter [ ][5][Master Code][code number 01 to 32][new access code]. The code number is a double
digit from 01 to 32. Access codes must be four digits unless otherwise indicated by your installer.
Enter digits 0 through 9 only. Press [#] to return to the Ready state.
If an access code already exists for the code number you have selected, it will be replaced by the new
code. Be sure to record your new code(s) on the "System Information" page in this book.
To erase a code:
Enter [ ][5][Master Code][code number 01 to 32][ ]. Press [#] to return to the Ready state. The
Master code cannot be erased.
Continued on page 10 ...
7
Hide quick links:
Advertisement
Table of Contents
