Related Manuals for Agri-Fab LBD48C
Summary of Contents for Agri-Fab LBD48C
- Page 1 OWNERS MANUAL Model No. LBD48C 48" SNOW BLADE 48" SNOW BLADE CAUTION: Read Rules for Safe Operation and Instructions Carefully FORM NO. 46864 (9/96) PRINTED IN U.S.A.
-
Page 2: Table Of Contents
RULES FOR SAFE OPERATION Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. LOOK FOR THIS SYMBOL TO POINT OUT IMPORTANT SAFETY PRECAUTIONS. MEANS -- ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED. -
Page 3: Carton Contents
48" SNOW BLADE CARTON CONTENTS CARTON CONTENTS REF. QTY. DESCRIPTION REF. QTY. DESCRIPTION Blade Assembly Angle Lock Bars Pivot Support Bracket Brace Mount Bracket (L.H.) Pivot Support Plate Brace Mount Bracket (R.H.) Cross Brace Channel Assembly Frame Pivot Support (L.H.) Grip Assembly Frame Pivot Support (R.H.) Blade Adjust Spring... -
Page 4: Full Size Hardware Chart
REF. QTY. DESCRIPTION Spring Mount Rod Palnut, 3/8" Cotter Pin 1/8" x 1-1/4" Angle Lock Spring Cable End Fitting Hex Jam Nut 5/16 Thread Spacer, 9/16" OD x 5/8" Hex Bolt, 5/16-18 x 1-1/2" Hex Lock Nut 5/16-18 Thread Cable Mount Bracket Hex Bolt 1/4-20 x 1-1/4"... -
Page 5: Assembly
ASSEMBLY Place the lift link inside the pivot support bracket. The TOOLS REQUIRED FOR ASSEMBLY long pin on the lift link goes through the slot in the pivot Pliers support bracket. The short pin goes through the hole Hammer shown in figure 3. Secure short pin with 1/8" x 1-1/4" Adjustable Wrench (or socket set) cotter pin. - Page 6 NOTE: To attach the frame reinforcement bracket in the Raise the mower lift assembly. next step, the tractor hood can be removed for easier access. Refer to your owner's manual for removal of Slide blade frame assembly under tractor, with the brace hood.
- Page 7 At this time tighten all items previously left untight- NOTE: Angle lock bars should pivot freely; and when ened. they are pulled all the way back, the channel/ Assemble the two angle lock bars together as shown in pivot plate assembly should be unlocked and figure 9 so that all holes are aligned.
- Page 8 Assemble one 5/16 jam nut approximately 3/4" onto NOTE: The other end of the control cable will be threaded end of control cable. Assemble threaded cable attached in a later step. end through round hole in cable mount bracket and secure with another 5/16 jam nut.
- Page 9 To attach loose end of cable to handle assembly, pass cable around outside and underneath handle assembly as shown in figure 17. Mount one 5/16" jam nut approxi- PIVOT SUPPORT 1/2" WASHER mately 3/4" onto threaded end of control cable. Insert BRACKET CHANNEL threaded end of cable up through cable mount ear on...
-
Page 10: Operation And Adjustments
Raise the blade to the transport position. (This will require extra effort since the extension spring is not yet attached.) Attach the long end of the extension spring to the upper hole in the pivot support bracket and the short end to the center slot in the channel as shown in figure 20. - Page 11 OPERATION KNOW YOUR SNOW BLADE READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR SNOW BLADE. Compare the illustration below with your snow blade to familiarize yourself with the various controls and their locations. HANDLE TUBE LOCK RELEASE GRIP ASS’Y. BLADE PIVOT ROD ANGLE LOCK...
-
Page 12: Customer Responsibilities
OPERATION NOTE: Wheel weights and tire chains must be used with your snow blade for traction. CAUTION: KNOW THE TERRAIN. AVOID EXCEPTIONALLY STEEP CAUTION: INSPECT THE AREA TO BE SLOPES OR DROP OFFS WHICH MAY WORKED CAREFULLY BEFORE BE HIDDEN BY THE SNOW. OPERATING THE SNOW BLADE. -
Page 13: Storage
SERVICE AND ADJUSTMENTS To Adjust Blade Spring To Adjust the Blade Pivot Lock Mechanism The tension of the blade adjust spring is adjustable to If the blade will not unlock and pivot, the angle lock permit blade to tilt forward to by-pass solid obstructions. bars are not disengaging from slots in pivot plate. -
Page 15: Repair Parts
REPAIR PARTS LIST FOR MODEL LBD48C - 48" SNOW BLADE REF. PART QTY. DESCRIPTION REF. PART QTY. DESCRIPTION 23955 Blade 48" 46049 Rod, Blade Pivot 23956 Wear Plate 48" 62972 Ass'y Lift Handle Tube 62980 Reinforcement Plate Ass'y 23967 Bracket, Brace Mount (rear) (LH) 43080 Bolt, Carriage 5/16-18 x 3/4"...