Omron BP710 Instruction Manual

Main Unit:
INSTRUCTION MANUAL
Automatic
Blood Pressure Monitor
Model BP710
START/STOP button
5325502-1B
Components:
INTRODUCTION
® ®
Thank you for purchasing the OMRON BP710 IntelliSense Automatic Blood
Pressure Monitor.
Fill in for future reference.
DATE PURCHASED: __________________
SERIAL NUMBER: ____________________
• Staple your purchase receipt here
• Register your product on-line at
www.register-omron.com
Your new digital blood pressure monitor uses the oscillometric method of blood
pressure measurement. This means the monitor detects your blood's movement through
your brachial artery and converts the movements into a digital reading. An
oscillometric monitor does not need a stethoscope so the monitor is simple to use.
The BP710 comes with the following components:
Irregular Heartbeat symbol
• Monitor • Standard Adult Arm Cuff
• Instruction Manual printed in English and Spanish • Quick Start Guide
The BP710 IntelliSense ® Automatic Inflation Blood Pressure Monitor is intended for
home use.
SAVE THESE INSTRUCTIONS
IRREGULAR HEARTBEAT SYMBOL (
When the monitor detects an irregular rhythm two or more times during the
measurement, the Irregular Heartbeat Symbol (
SAFETY INFORMATION
measurement values.
An irregular heartbeat rhythm is defined
To assure the correct use of the product, basic safety measures should always be as a rhythm that is more than 25%
followed including the warnings and cautions listed in this instruction manual.
slower or 25% faster from the average
rhythm detected while the monitor is
SAFETY SYMBOLS USED IN THIS INSTRUCTION MANUAL
measuring the systolic and diastolic
Indicates a potentially hazardous situation which, if not avoided,
blood pressure.
WARNING
could result in death or serious injury.
If the irregular heartbeat symbol (
Indicates a potentially hazardous situation which, if not avoided,
displays with your measurement results,
CAUTION may result in minor or moderate injury to the user or patient or
we recommend you consult your
damage to the equipment or other property.
physician. Follow the directions of your
doctor.
OPERATING THE DEVICE
HEARTBEAT SYMBOL/HYPERTENSION INDICATOR (
Contact your physician for specific information about your blood pressure.
Self-diagnosis and treatment using measured results may be dangerous. Follow the
instructions of your physician or licensed healthcare provider.
The monitor is not intended to be a diagnostic device.
If battery fluid should get in your eyes, immediately rinse with plenty of clean
water. Contact a physician immediately.
Read all of the information in the instruction manual and any other literature in the
box before operating the unit.
This device is intended for use in measuring blood pressure and pulse rate in the
adult population. Do not use this device on infants or persons who cannot express
their intentions.
Read the Special Conditions section of the instruction manual if your systolic
The American Heart Association recommends the following guideline for upper limit
pressure is known to be more than 220 mmHg. Inflating to a higher pressure than
of normal for home blood pressure readings:
necessary may result in bruising where the cuff is applied.
Operate the device only as intended. Do not use the device for any other purpose.
Dispose of the device, components and optional accessories according to applicable
local regulations. Unlawful disposal may cause environmental pollution.
Do not use a cellular phone near the device. It may result in an operational failure.
Use only Omron authorized parts and accessories. Parts and accessories not
approved for use with the device may damage the unit.
Use only 1.5 V "AAA" alkaline batteries with this device. Do not use other types of
batteries. This may damage the unit.
CARE AND MAINTENANCE
Do not subject the monitor to strong shocks, such as dropping the unit on the floor.
Do not submerge the device or any of the components in water.
Store the device and the components in a clean, safe location.
Changes or modification not approved by the manufacturer will void the user
Omron Healthcare recommends you contact your physician if the Heartbeat Symbol
warranty. Do not disassemble or attempt to repair the unit or components.
(
1 American Heart Association Scientific Statement 2004
BEFORE TAKING A MEASUREMENT
To ensure a reliable reading follow these recommendations:
1. Avoid eating, drinking alcohol, smoking, exercising, and bathing for 30 minutes
before taking a measurement. Rest for at least 15 minutes before taking the
1. Press the
measurement.
2. Stress raises blood pressure. Avoid taking measurements during stressful times.
3. Measurements should be taken in a quiet place.
4. Remove tight-fitting clothing from your left arm.
2. Install 4 "AAA" size batteries so the + (positive) and
5. Sit on a chair with your feet flat on the floor. Rest your left arm on table so that the
cuff is at the same level as your heart.
6. Remain still and do not talk during the measurement.
7. Wait 2-3 minutes between measurements. The wait time allows the arteries to return
to the condition prior to taking the blood pressure measurement. You may need to
increase the wait time depending on your individual physiological characteristics.
8. Keep a record of your blood pressure and pulse readings for your physician. A
single measurement does not provide an accurate indication of your true blood
3. Replace the battery cover.
pressure. You need to take and record several readings over a period of time. Try to
measure your blood pressure at the same time each day for consistency.
BATTERY REPLACEMENT
KNOW YOUR UNIT
When the Low Battery Indicator appears on the display, turn the monitor off and
Display
remove all the batteries. Replace with four new batteries at the same time. Long-life
Battery compartment
alkaline batteries are recommended.
Memory (M) button
Air jack
INSTRUCTION MANUAL
Air tube Automatic
Blood Pressure Monitor
Model BP710
5325502-1B
INTRODUCTION
Thank you for purchasing the OMRON BP710 IntelliSense Automatic Blood
Pressure Monitor. Fill in for future reference.
DATE PURCHASED: __________________
SERIAL NUMBER: ____________________
Air plug
Staple your purchase receipt here
Your new digital blood pressure monitor uses the oscillometric method of blood
pressure measurement. This means the monitor detects your blood's movement through
Standard Adult Arm Cuff Instruction oscillometric monitor does not need a stethoscope so the monitor is simple to use. your brachial artery and converts the movements into a digital reading. An Quick Start
The BP710 comes with the following components:
• Instruction Manual printed in English and Spanish • Quick Start Guide • Monitor • Standard Adult Arm Cuff
The BP710 IntelliSense Automatic Inflation Blood Pressure Monitor is intended for
home use.
Manual SAVE THESE INSTRUCTIONS Guide
APPLYING THE CUFF ON THE LEFT ARM
1. Make sure the air plug is securely inserted
UNIT DISPLAY
in the main unit.
Systolic blood pressure
Diastolic blood pressure
2. Remove tight-fitting clothing from your upper
Heartbeat symbol
Memory symbol
arm.
(Displayed when viewing Pulse display
values stored in memory)
Deflation symbol
Battery low indicator
3. Apply the cuff to your left upper arm so
the arrow is centered on the inside of your arm
DISPLAY SYMBOLS
and aligned with your middle finger.
The air tube runs down the inside of your arm.
The bottom of the cuff should be
)
approximately 1/2 " above your elbow.
) will appear on the display with the
4. Wrap the cuff firmly in place around your
arm using the cloth fastening.
Normal Heartbeat
Pulse
Blood
pressure
Irregular Heartbeat
)
Short Long
APPLYING THE CUFF ON THE RIGHT ARM
Pulse
When taking a measurement using the right arm, use this instruction for Step 3.
Blood
pressure
Apply the cuff to your right upper arm so
the arrow and the air tube runs along the inside
)
of your arm. The bottom of the cuff should be
TAKING A MEASUREMENT
approximately 1/2 " above your elbow.
The Heartbeat Symbol ( ) flashes on the display during the measurement. The
Heartbeat Symbol ( ) flashes at every heartbeat.
When the measurement is complete, the Heartbeat Symbol ( ) flashes on the
display with your blood pressure and pulse rate if the reading is above 135 for the
NOTE: Be careful not to rest your arm on the air tube. This will restrict the flow of air
Systolic Blood Pressure value and/or above 85 for the Diastolic Blood Pressure
value.
USING THE MEMORY FUNCTION
The Heartbeat Symbol ( ) flashes when the blood pressure reading stored in the
memory is above 135 for the Systolic Blood Pressure value and/or above 85 for the
Diastolic Blood Pressure value.
AHA Home Guideline for Upper Limit of Normal BP
Systolic Blood Pressure 135 mmHg
1. Sit on a chair with your feet flat on the floor.
Place your arm on a table so the cuff is level
Diastolic Blood Pressure 85 mmHg
with your heart.
This is a general guideline because blood pressure depends on age and morbidity.
Keep still and do not talk during measurement.
The AHA recommends a lower home blood pressure goal for certain patients,
1
including diabetic patients, pregnant women, and patients with renal failure .
2. Press the START/STOP button.
All symbols appear on the display.
WARNING
The cuff starts to inflate automatically. As the cuff inflates, the monitor automatically
The monitor is not intended to be a diagnostic device.
determines your ideal inflation level.
WARNING Remain still and do not move your arm until the entire measurement process is completed.
Contact your physician for specific information about your blood pressure.
Self-diagnosis and treatment using measured results may be dangerous.
Follow the instructions of your physician or licensed healthcare provider.
) flashes on the display with your measurement values.
NOTE: To stop the inflation or measurement, push the START/STOP button. The
3. Inflation stops automatically and the measurement is started.
BATTERY INSTALLATION
As the cuff deflates, decreasing numbers appear on the display and the Heartbeat
Symbol (
CAUTION
Use only 1.5V "AAA" alkaline batteries with this device.
indicator on the battery cover and
slide the cover off in the direction of the arrow.
4. When the measurement is complete, the arm cuff completely
deflates. Your blood pressure and pulse rate are displayed.
- (negative) polarities match the polarities of
the battery compartment as indicated.
NOTE: 4 "AAA" size batteries are not included
in this unit.
5. Press the START/STOP button to turn the monitor off.
NOTE: The monitor will automatically turn off after five minutes.
SPECIAL CONDITIONS
CAUTION
Low Battery Indicator
WARNING
If battery fluid should get in your eyes, immediately rinse with
plenty of clean water. Contact a physician immediately.
CAUTION
Dispose of the device, components and optional accessories according to
applicable local regulations. Unlawful disposal may cause environmental
pollution.
NOTES: • Do not apply more pressure than necessary.
APPLYING THE ARM CUFF
CAUTION When the measurement is complete, the arm cuff completely deflates.
Your blood pressure and pulse rate are displayed.
Read all of the information in the instruction manual and any other
literature in the box before operating the unit.
CAUTION
This device is intended for use in measuring blood pressure and
Every time you complete a measurement the monitor stores the blood pressure and pulse
pulse rate in the adult population. Do not use this device on infants
rate in the memory. The monitor automatically stores up to 14 sets of measurement values
or persons who cannot express their intentions.
(systolic pressure, diastolic pressure, and pulse rate). When 14 sets of measurement
values are stored, the oldest record is deleted to save the most recent values.
1. Press the Memory (M) button.
The most recent set of measurement values appears on the display.
The values are displayed from the most recent to the oldest.
NOTE: The number of the reading stored in the memory appears for a second
2. Press the START/STOP button to turn the unit off.
TO DELETE ALL THE VALUES STORED IN MEMORY
Left Arm
You cannot partially delete values stored in the memory. All values will be deleted.
1/2 inch (1 - 2 cm)
1. Press the Memory (M) button.
Then while holding it down, press the START/STOP button down for more than 2
seconds until the display appears as illustrated below.
Arrow
Air Tube
2. Press the START/STOP button to turn the unit off.
NOTE: The monitor will automatically turn off after five minutes.
To keep your digital blood pressure monitor in the best condition and protect the unit
from damage, follow the directions listed below:
Do not forcefully bend the arm cuff or air tube. Do not fold tightly.
Clean the monitor with a soft dry cloth.
Right Arm
Do not use any abrasive or volatile cleaners.
Do not attempt to clean the cuff.
CAUTION
Arrow
CAUTION
to the cuff.
CAUTION
Remove the batteries if the unit will not be used for three months or longer. Always
replace all the batteries with new ones at the same time.
Use the unit consistent with the instruction provided in this manual.
Use only authorized parts and accessories.
Use the unit in a manner consistent with the instructions provided in this manual.
TAKING A MEASUREMENT
CAUTION
CAUTION
monitor will stop inflating, start deflating, and will turn off.
) flashes.
No power.
No display appears on the unit.
Measurement values appear too
high or too low.
Inflating to a higher pressure than necessary may result in bruising where
Note:
the cuff is applied.
POTENTIAL FOR RADIO/TELEVISION INTERFERENCE (for U.S.A. only)
If your systolic pressure is known to be more than 220 mmHg, press and
This product has been tested and found to comply with the limits for a Class B digital
hold the START/STOP button until the monitor inflates 30 to 40 mmHg
higher than your expected systolic pressure. device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference
in a residential installation. The product generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If the product does
cause harmful interference to radio or television reception, which can be determined by
turning the product on and off, the user is encouraged to try to correct the interference
by one or more of the following measures:
• The monitor will not inflate above 299 mmHg.
• Reorient or relocate the receiving antenna.
• Increase the separation between the product and the receiver.
• Connect the product into an outlet on a circuit different from that to which the
receiver is connected.
USING THE MEMORY FUNCTION
• Consult the dealer or an experienced radio/TV technician for help.
POTENTIAL FOR RADIO/TELEVISION INTERFERENCE (for Canada only)
This digital apparatus does not exceed the Class B limits for radio noise emissions
from digital apparatus as set out in the interference-causing equipment standard entitled
"Digital Apparatus", ICES-003 of the Canadian Department of Communications.
Cet appareil numérique respecte les limites de bruits radioeléctriques applicables aux
appareils numériques de Clase B prescrites dans la norme sur le materiel brouilleur:
"Appareils Numériques", ICES-003 édictée par le minister des communications.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
before the pulse rate is displayed. The newest set is numbered "1".
Your BP710 IntelliSense
is warranted to be free from defects in materials and workmanship appearing within 2
years from the date of purchase, when used in accordance with the instructions
provided with the monitor. The arm cuff is warranted to be free from defects in
materials and workmanship appearing within one year from the date of purchase when
the monitor is used in accordance with the instructions provided with the monitor. The
above warranties extend only to the original retail purchaser.
We will, at our option, repair or replace without charge any monitor or arm cuff
covered by the above warranties. Repair or replacement is our only responsibility and
your only remedy under the above warranties.
To obtain warranty service contact Customer Service by calling 1-800-634-4350 for
the address of the repair location and the return shipping and handling fee.
Enclose the Proof of Purchase. Include a letter, with your name, address, phone
number, and description of the specific problem. Pack the product carefully to prevent
damage in transit. Because of possible loss in transit, we recommend insuring the
product with return receipt requested.
CARE AND MAINTENANCE
THE FOREGOING IS THE SOLE WARRANTY PROVIDED BY OMRON IN
CONNECTION WITH THIS PRODUCT, AND OMRON HEREBY
DISCLAIMS ANY OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. IMPLIED WARRANTIES AND
OTHER TERMS THAT MAY BE IMPOSED BY LAW, IF ANY, ARE
LIMITED IN DURATION TO THE PERIOD OF THE ABOVE EXPRESS
WARRANTY.
OMRON SHALL NOT BE LIABLE FOR LOSS OF USE OR ANY OTHER
Do not submerge the device or any of the components in water. Do
SPECIAL, INCIDENTAL, CONSEQUENTAIL OR INDIRECT COSTS,
not subject the monitor to extreme hot or cold temperatures,
EXPENSES OR DAMAGES.
humidity or direct sunlight.
This warranty provides you with specific legal rights, and you may have other rights
that vary by jurisdiction. Because of special local requirements, some of the above
Store the device and the components in a clean, safe location.
limitations and exclusions may not apply to you.
Do not subject the monitor to strong shocks, such as dropping the unit on the floor. Visit our web site at:
Call toll free:
Model:
Display:
Use only Omron authorized parts and accessories. Parts and accessories
Measurement Range:
not approved for use with the device may damage the unit.
Accuracy/Calibration:
Changes or modification not approved by the manufacturer will void the user
Inflation:
warranty. Do not disassemble or attempt to repair the unit or components.
Deflation:
ERROR INDICATORS
Rapid Air Release:
Measurement Method:
SYMBOL CAUSE CORRECTION
Power Source:
Battery Life:
Take another measurement and
Monitor could not
remain still until the measurement Operating Temperature
detect pulse wave.
is complete. /Humidity:
Storage Temperature
Cuff under-inflated.
/Humidity/Air Pressure:
Cuff not applied
Remove the arm cuff.
correctly. Main Unit Weight:
Read "Taking a Measurement".
Wait 2-3 minutes. Main Unit Dimensions:
Cuff over-inflated.
Take another measurement.
Cuff Size:
Replace the four batteries. Refer to
Cuff Circumference:
Batteries are worn.
"Battery Installation".
Memory:
Contents:
Device error. Contact Customer Service.
Optional Accessories:
TROUBLESHOOTING TIPS
PROBLEM CAUSES AND SOLUTIONS NOTE: These specifications are subject to change without notice.
Replace all four batteries with new ones.
Check the battery installation for proper placement
of the battery polarities. Omron Healthcare, Inc.
1200 Lakeside Drive
Blood pressure varies constantly. Many factors
Bannockburn, IL 60015
including stress, time of day, how you wrap the
www.omronhealthcare.com
cuff, may affect your blood pressure.
Copyright © 2010 Omron Healthcare, Inc.
Review the sections "Before Taking a
Measurement" and "Taking a Measurement".
Made in China
HEM-7113-Z_B_M03_100519.pdf
FCC STATEMENT
LIMITED WARRANTIES
® Automatic Blood Pressure Monitor, excluding the arm cuff,
FOR CUSTOMER SERVICE
www.omronhealthcare.com
1-800-634-4350
SPECIFICATIONS
BP710 (HEM-7113-Z)
LCD Digital Display
Pressure: 0 to 299 mmHg, Pulse: 40 to 180/min.
Pressure: ±3mmHg or 2% of reading
Pulse: ±5% of reading
Automatic by electric pump
Automatic pressure release valve
Automatic exhaust valve
Oscillometric method
1.5V 4 "AAA" batteries
Approx. 300 uses with 4 new alkaline batteries
50ºF to 104ºF (10ºC to 40ºC) /15 to 90% RH
-4ºF to 140ºF (-20ºC to 60ºC) /10 to 95% RH
700-1060 hPa
Approximately 8 5/8 oz. (245g)
not including batteries
Approx. 5"(l) × 4 1/8"(w) × 2 1/2" (h)
(128 mm × 104 mm × 64 mm)
Approximately 5 3/4"(w) × 17 1/2"(l) (146 mm × 446 mm)
Cuff tube 23 5/8" (600 mm)
Fits arm circumferences 9" to 13"
(220 mm to 320 mm)
Up to 14 readings
Main Unit, Standard Adult Arm Cuff, Instruction Manual,
and Quick Start Guide
Large Cuff 13'' - 17'' (320 mm - 420 mm)