Tool/Fastener Specifications - Bostitch 651 SERIES Operation And Maintenance Manual

MAINTAINING THE TOOL
When working on air tools note the warnings in this manual and use extra care when
evaluating problem tools.
TOOL SPECIFICATIONS
All dimensions in inches unless otherwise specified.
Description
Operation Pressure Range
Fastener Type
Fastener Gauge
Fastener Range
Magazine Capacity
Length
Width
Height
Weight
Tool Air Fitting:
This tool uses a free-flow connector plug, 1/4" N.P.T. The minimum inside diameter should be .200" (5mm).
The fitting must be capable of discharging tool air pressure when disconnected from the air supply.
Operating Pressure:
70 to 120 p.s.i.g. (4.9 to 8.43 kg/cm
performance. DO NOT EXCEED THIS RECOMMENDED OPERATING PRESSURE.
Air Consumption:
The 651 Series staplers require 5.3 cubic feet per minute or C.F.M. (150 liters per minute or LT/MIN) of free
air at 80PSI (5.6 kg/cm
sized air compressor, take the actual rate at which the tool will be run and compare the required C.F.M.
(LT/MIN) to the compressors free air delivery (C.F.M./ LT/MIN) at 80 PSI (5.6 kg/cm
For example, if your fastener usage averages 50 fasteners per minute, you need 50% of the tools C.F.M.
required to operate the tool at the rate of 100 fasteners per minute. In this case, be sure that your air
compressor can deliver a minimum of 2.7 C.F.M. (75 LT/MIN) at 80 PSI(5.6 kg/cm
FASTENER SPECIFICATIONS
Tool Model
651S5-1
* Stainless steel fasteners also available in certain sizes. Visit www.BOSTITCH.com for further details.
NOTE:
BOSTITCH tools have been engineered to provide superior customer satisfaction and are
designed to achieve maximum performance when used with precision BOSTITCH fasteners engineered to
the same exacting standards. BOSTITCH cannot assume responsibility for product performance if
our tools are used with fasteners or accessories not meeting the specific requirements established
for genuine BOSTITCH fasteners and accessories.
2
). Select the operating pressure within in this range for best fastener
2 ) to operate at a rate of 100 fasteners per minute. To determine the appropriately
Fastener SKU
16S5-35
16S5-38
16S5-44
16S5-44GAL
16S5-50
16S5-50GAL
17S5-25G
17S5-28G
17S5-31G
17S5-34G
17S5-38G
17S5-41G
17S5-44G
17S5-50G
651S5
7/16" Crown Stapler
70-120 PSI (4.9 to 8.43kg/cm
16S5 & 17S5 Series Staples
16 & 17 Gauge
1" to 2" (25mm to 50mm)
120
14"
3 1/8"
11"
4.3 lbs.
Gauge Crown Width
7/16"
16
16 7/16"
16 7/16"
16 7/16"
16 7/16"
7/16"
16
7/16"
17
7/16"
17
17 7/16"
17 7/16"
17 7/16"
17 7/16"
17 7/16"
17 7/16"
-4-
2
)
2
).
2
) for optimum performance.
Length
1-3/8" (35mm)
1-1/2" (38mm)
1-3/4" (44mm)
1-3/4" (44mm)
2" (50mm)
2" (50mm)
1" (25mm)
1-1/8" (28mm)
1-1/4" (31mm)
1-3/8" (34mm)
1-1/2" (38mm)
1-5/8" (41mm)
1-3/4" (44mm)
2" (50mm)