1. Manuals
  2. Brands
  3. Woods Manuals
  4. Lawn Mower
  5. 42C-6
  6. Operator's manual

Woods 42C-6 Operator's Manual

Rotary mower
Hide thumbs
Table of Contents

Advertisement

Quick Links

ROTARY MOWER

42C-6
Tested. Proven. Unbeatable.

Advertisement

Table of Contents
loading

Related Manuals for Woods 42C-6

Summary of Contents for Woods 42C-6

  • Page 1: Rotary Mower

    ROTARY MOWER 42C-6 Tested. Proven. Unbeatable.

  • Page 2: Introduction

    Operator’s Manual. If using the mail-in form, the dealer is to return the prepaid postage portion to Woods, give one copy to the customer, and retain one copy. Failure to register the product does not diminish customer’s warranty rights.

  • Page 3: Table Of Contents

    TABLE OF CONTENTS INTRODUCTION ..........2 GENERAL INFORMATION .

  • Page 4: Safety Rules

    SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Make sure all safety decals are installed. Safety is a primary concern in the design and Replace if damaged. (See Safety Decals section for manufacture of our products. Unfortunately, our location.) efforts to provide safe equipment can be wiped Make sure shields and guards are properly out by an operator’s single careless act.
  • Page 5 SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Do not stop, start, or change directions sud- neath equipment or between moveable parts even denly on slopes. when the engine has been turned off. Hydraulic system leak down, hydraulic system failures, Use extreme care and reduce ground speed on mechanical failures, or movement of control levers slopes and rough terrain.

  • Page 6: Safety Decals

    Replacement safety decals can be ordered free from your Woods dealer. To locate your nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or in the United States and Canada call 1-800-319-6637.

  • Page 7: Operation 7

    OPERATION ATTITUDE ADJUSTMENT WARNING Attitude can be adjusted by selecting the proper hole when connecting the channel arms to the mounting ■ Do not allow children or unqualified persons to frame. operate equipment. ■ NOTICE Keep bystanders away from equipment while it is in operation.

  • Page 8: Service

    Inspect machine and replace worn or damaged parts. ● Sand down scratches and the edges of areas of missing paint and coat with Woods spray paint of matching color (purchase from your Woods dealer). ● Replace any safety decals that are missing or not readable (supplied free by your Woods dealer).

  • Page 9: Assembly 9

    ASSEMBLY on the bottom side of the blade when installed. Insert blade pin (11) through blades, rotate blade pin retainer WARNING washer (10) over pin, tighten bolt (12) snugly. Do not over tighten; do not follow torque chart recommenda- ■ Keep all persons away from operator control tions.
  • Page 10 Figure 6. Side Shield & Baffle Installation Figure 5. Side Skid and Side Shield Discharge Chute Installation SIDE SHIELD OR DISCHARGE CHUTE Remove side shield (4). Attach discharge chute (13) to INSTALLATION mower frame with 3/8 x 1" bolts (20) and 3/8" flanged A side shield and discharge chute are provided for right lock nuts (25).
  • Page 11 MOUNTING FRAME ASSEMBLY with 5/8" flat washer (95), lock washer (96) and nut (97). Push Channel / Push Channel Mounting Mower Frame to Idler Bracket Angles and Lift Bars Slide mower frame under tractor. Adjust front axle out Loosely assemble the following (see page 18): to provide clearance of mower when turning.
  • Page 12 Figure 8. Mounting Frame Assembly Photo 12 Assembly 29900 (Rev. 7/6/2007)
  • Page 13 Figure 9. Mounting Frame Assembly Photo with Rear Shield Assembly 13 29900 (Rev. 7/6/2007)
  • Page 14 Figure 10. Lift Assembly Photo 14 Assembly 29900 (Rev. 7/6/2007)

  • Page 15: Dealer Check Lists

    DEALER CHECK LISTS PRE-DELIVERY CHECK LIST DELIVERY CHECK (DEALER’S RESPONSIBILITY) (DEALER’S RESPONSIBILITY) Inspect the equipment thoroughly after assembly to ___ Instruct customer how to lubricate and explain ensure it is set up properly before delivering it to the importance of lubrication. customer.

  • Page 16: Parts Lists

    42-6 CW MAIN FRAME ASSEMBLY 16 Parts 29900 (Rev. 7/6/2007)
  • Page 17 42-6 CW MAIN FRAME ASSEMBLY PART DESCRIPTION PART DESCRIPTION HARDWARE 9874 Frame 24597 * 3/8 NC x 3/4 Carriage bolt 26403 Front corner baffle 839 * 3/8 NC x 1 HHCS GR5 4141 Right side skid 976 * 3/8 NC x 1-1/2 HHCS GR5 26396 Right side shield 838 *...
  • Page 18 42C-6 MOUNTING FRAME ASSEMBLY DRAWING 18 Parts 29900 (Rev. 7/6/2007)
  • Page 19 42C-6 MOUNTING FRAME ASSEMBLY PART DESCRIPTION PART DESCRIPTION HARDWARE 27657 Lift bar 2688 * 5/32 Hair cotter pin 1533 Bottom lift arm 1256 * 3/16 x 1 Cotter pin 1441 Upper lift arm 2457 * 1/4 NC x 3/4 HHCS GR5...
  • Page 20 OVERRUNNING CLUTCHES PART DESCRIPTION ------ * 1/8 Pipe plug (used on earlier models) 3174 Oil seal 839 * 3/8 NC x 1 HHCS GR5 838 * 3/8 Lock washer ZP 3333 Ratchet cap (includes 2 & 6 installed) 3175 1-3/4 x 2-1/4 x 1/2 Bushing 3171 Ratchet with hex hole 3176...
  • Page 21 Lift Chain Hook-Up Table Mower Model Special Chains Used Lift Chain Attach Plt Holes Used for Spring Number Notes To Lift Part No No Used Description To Holes in Upper End to Lower End to Mower Hole Let- Hole Let- Lever Hole tered: tered:...
  • Page 22 Manual Height Adjustment 22 Parts 29900 (Rev. 7/6/2007)
  • Page 23 Manual Height Adjustment REF PART DESCRIPTION REF PART DESCRIPTION 18336 Caplug, 1-1/16 - 121D SAE thread ----- Chain (see chart for chain used on your mounting) 2457 1/4 NC x 3/4 HHCS GR5 4155 2-3 1/4 Cold shut repair link 6128 1/4 NC Lock nut 10693...

  • Page 24: Spindle Assembly

    SPINDLE ASSEMBLY REF PART DESCRIPTION 18355 CW Blade spindle 18359 1-3/8 x 1-3/4 x 5/8 Sleeve 2718 1-3/4 x 2-3/8 x 13 GA Flat washer 2715 Seal for 1-3/4 shaft 2717 Bearing cone 18361 Spindle housing with cups 2716 Bearing cup 195 * Straight 1/8 pipe thread grease fitting...

  • Page 25: Bolt Torque Chart

    BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly.

  • Page 26: Bolt Size Chart

    BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. SAE Bolt Thread Sizes 5/16 Metric Bolt Thread Sizes 10MM 12MM 14MM 16MM 18MM ABBREVIATIONS AG .............. Agriculture MPa ............Mega Pascal ASABE ....American Society of Agricultural &...
  • Page 27 BW1260, BW1800, 2162, 3240, DS1260, DSO1260, DS1440, TS1680 Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of WOODS, has been subjected to improper operation, improper maintenance, misuse, or an accident. This Warranty does not apply in the event that the product has been materially modified or repaired by someone other than WOODS, a WOODS authorized dealer or distributor, and/or a WOODS authorized service center.
  • Page 28 ©2007 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and "Tested. Proven. Unbeatable." are trademarks of Woods Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual are the property of their respective companies or mark holders.

Table of Contents