Table of Contents
Advertisement
BEFORE USE
Checking the appliance
After removing the packaging, make sure the product is com-
plete and undamaged and that all accessories are present. Do
not use the appliance if it is visibly damaged. Contact De'Longhi
Customer Services.
Installing the appliance
Important!
When you install the appliance, you should respect the follow-
ing safety warnings:
•
The appliance gives off heat. After positioning the appli-
ance on the worktop, leave a space of at least 3 cm be-
tween the surfaces of the appliance and the side and rear
walls and at least 15 cm above the coffee machine.
•
Water penetrating the appliance could cause damage. Do
not place the appliance near taps or sinks.
•
The appliance could be damaged if the water it contains
freezes. Do not install the appliance in a room where the
temperature could drop below freezing point.
•
Arrange the power cable in such a way that it cannot be
damaged by sharp edges or contact with hot surfaces (e.g.
electric hot plates).
Connecting the appliance
Important!
Check that the mains power supply voltage corresponds to
the value indicated on the rating plate on the bottom of the
appliance.
Connect the appliance to an efficiently earthed and correctly
installed socket with a minimum current rating of 10A only.
If the power socket does not match the plug on the appliance,
have the socket replaced with a suitable type by a qualified
professional.
Setting up the appliance
Please note :
•
Coffee has been used to factory test the appliance and it is
therefore completely normal for there to be traces of cof-
fee in the mill. The machine is, however, guaranteed to be
new.
•
You should customise water hardness as soon as possible
following the instructions in the section "Setting water
hardness" on page 17.
1. Insert the power cable connector into the socket at the
back of the appliance and connect the appliance to the
mains electricity supply (fig. 1). Make sure the main switch
at the back of the appliance is pressed (fig. 2).
You must first choose the language (the languages scroll
through at intervals of about 3 seconds):
2. When English appears, press the
for a few seconds until "ENGLISH set" is displayed.
Follow the instructions indicated on the appliance display:
3. "FILL TANK": remove the water tank, fill to the MAX line
with fresh water (fig. 4A), then replace in the appliance
(fig. 4B).
4. "INSERT WATER SPOUT": Check that the hot water spout is
inserted on the nozzle and place a container holding a mini-
mum of 100 ml underneath (fig. 5).
5. "HOT WATER Confirm?" appears on the display.
6. Press the
button to confirm. The appliance delivers
water from the spout then goes off automatically.
The coffee machine is now ready for normal use.
Please note!
•
When using the appliance for the first time, you need to
make 4-5 cups of coffee or 4-5 cappuccinos before it starts
to give satisfactory results.
•
To enjoy your coffee even more and improve the perfor-
mance of your appliance, we recommend installing a water
softener filter as described in the section " WATER SOFTEN-
ER FILTER " (page 17). If your model is not provided with
a filter, you can request one from De'Longhi Customer
Services.
TURNING THE APPLIANCE ON
Please note!
Before turning the appliance on, make sure the main switch is
pressed (fig. 2).
Each time the appliance is turned on, it performs an automatic
preheat and rinse cycle which cannot be interrupted.
The appliance is ready for use only after completion of this cycle.
Danger of burns!
During rinsing, a little hot water comes out of the coffee spouts
and is collected in the drip tray underneath.
Avoid contact with splashes of water.
•
To turn the appliance on, press the
The message "Heating up Please wait" is displayed.
After heating, the message "Rinsing" is displayed. As well as
heating the boiler, the appliance also heats the internal circuits
by circulating hot water.
The appliance is at temperature when the message "READY" is
displayed and the taste has been selected.
9
button (fig. 3)
button (fig. 6).
Hide quick links:
Advertisement
Table of Contents
Troubleshooting
