LG 22LG3DDH Setup Manual page 19

012 - IR BANKS EN (IR Banks Enable)
For direct access to a particular channel bank. When enabled, you
can access a channel bank by inputting the IR code for the bank.
013 - SCAN MODE (Functional after 2-5-5 + MENU transfer)
Allows variation in turning the TV ON/OFF with Channel Up/Down.
You may opt for TV channels only or TV channels + OFF/ON. If
set to 0, Channel Up/Down keys change channels only. If set to 1,
channel DOWN below the lowest channel or Channel UP above
the highest channel to turn the TV OFF.
014 - STRT CH IN SM (Start Channel in Scan Mode)
If set to 1, installs TV ON/OFF event below the start channel at
TV turn ON. If set to 1, the user can select channels with either
Channel Up/Down or by direct keypad entry. If set to 0, only those
channels that are entered for scanning can be selected.
015 - SLEEP TIMER
If set to 1, the Sleep Timer feature may be used. If set to 0, the
Sleep Timer is not available.
016 - EN TIMER (Enable On/Off Timers)
If set to 1, the Timer function is available to the end user and
enabled continuously. Set to 0 to disable On/Off timers.
Note: Clock must be set in order for timers to be used.
017 - ALARM
Gives the installer the option of making the Alarm function avail-
able to the end user. If set to 1, the Alarm function is available to
the end user. Set to 0 to disable the Alarm function.
Note: Clock must be set before the Alarm function will work.
020 - FEATURE LEVEL
For LG3DDH TVs, leave set to 1 (default) to enable Zenith IR
codes remote control operation.
For LD6DDH TVs, this item determines an additional IR code
scheme to which the TV will respond, allowing for the use of unique
IR codes based on "bed number" in a multi-TV single room installa-
tion. First determine the IR mode; then select the bed number.
IR Mode
Legacy (Hospital)
Multi-code Remote
Note: For further information, see documentation for the accessory
package that includes the multi-code remote.
021 - V-CHIP (Parental Control)
Set to 1 to activate V-Chip (Parental Control) and have it available
to the end user to filter and control or otherwise restrict program-
ming content that can appear. Set to 0 to turn the V-Chip feature
Off (not available to user); no programming restrictions can be set.
022 - MAX BLK HRS (Maximum Block Hours)
Sets hours from 0 to 99 for the maximum V-Chip (Parental Control)
block hours. Default setting is for 12 blocking hours.
206-4190
Bed # Values
1 – 2 0 – 1
1 – 9 16 – 24
Installer Menu (Cont.)
023 - CAPTION LOCK
If set to 0, captions are OFF when the TV is turned ON. Set to 1 to
use the caption setting configured before the TV was turned OFF
when the TV is turned ON.
025 - FUNCTION PRE (Function Preview)
Set to 0 to suppress channel preview from the Function Menu, if
available (i.e., the TV is not in Stand-alone Mode).
027 - HOSPITAL MODE
With this setting two things are affected: Channel Banks 1, 2, and
3 are accessible, while Channel Bank 4 can be made inactive by
removing all the channels from Channel Bank 4. Then, if Channel
Bank 4 is selected when the TV is turned ON, the TV screen will
show "Inactive TV." The Channel Bank 4 setup allows the hospital
to present TV viewing options to the patient. The patient can select
programming options available in Channel Banks 1, 2, or 3. Chan-
nel Banks are available in all Hospital Modes (1, 2, etc.).
The IR code that will control the TV depends on the Installer Menu
item 020 FEATURE LEVEL setting.
Set according to the pillow speaker supply voltage and audio
source (see table below). Note the following regarding pillow speak-
er voltage: +12 v identifies a Zenith pillow speaker, +5 v identifies a
Phillips pillow speaker, and -5 v identifies an RCA pillow speaker.
Note: The default setting (254) is not selectable in the Installer
Menu. If you ever need to restore the default setting, you must set
item 117 FACT DEFAULT to 1 to reload the factory default settings.
See item 117 description for further information.
Item
Hospital Mode
027
Value
000 Disabled
001 Enabled, Zenith Private Label
002 Enabled, Zenith Consumer
017 Enabled, Zenith Private Label
018 Enabled, Zenith Consumer
033 Enabled, Zenith Private Label
034 Enabled, Zenith Consumer
065 Enabled, Zenith Private Label
066 Enabled, Zenith Consumer
081 Enabled, Zenith Private Label
082 Enabled, Zenith Consumer
097 Enabled, Zenith Private Label
098 Enabled, Zenith Consumer
129 Enabled, Zenith Private Label
130 Enabled, Zenith Consumer
145 Enabled, Zenith Private Label
146 Enabled, Zenith Consumer
161 Enabled, Zenith Private Label
162 Enabled, Zenith Consumer
254 Enabled, Zenith Consumer
Pillow
Audio Source
Speaker
(Switch = Pillow)
Voltage
+12 v Pillow Only
+12 v Pillow Only
+12 v Pillow Only
+5 v Pillow Only
+5 v Pillow Only
-5 v Pillow Only
-5 v Pillow Only
+12 v Main Only
+12 v Main Only
+5 v Main Only
+5 v Main Only
-5 v Main Only
-5 v Main Only
+12 v Pillow & Main
+12 v Pillow & Main
+5 v Pillow & Main
+5 v Pillow & Main
-5 v Pillow & Main
-5 v Pillow & Main
0 v Main Only
19