Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Husqvarna TS 250 XL
Summary of Contents for Husqvarna TS 250 XL
-
Page 2: Table Of Contents
EVERY MACHINE IS THOROUGHLY TESTED BEFORE LEAVING THE FACTORY. EACH MACHINE IS SUPPLIED WITH A COPY OF THIS MANUAL. OPERATORS OF THIS EQUIPMENT MUST READ AND BE FAMILIAR WITH THE SAFETY WARNINGS. FAILURE TO OBEY WARNINGS MAY RESULT IN INJURY OR DEATH. FOLLOW INSTRUC- TIONS STRICTLY TO ENSURE LONG SERVICE IN NORMAL OPERATION. -
Page 3: Symbol Definitions
Symbol Definitions Symboles Definición De Los Simbolos • Please read the instructions for use prior to operating the machine for the first time. • Avant toute mise en service, lire attentivement la notice et se familiariser avec la machine. • Antes de la puesta en marcha, lea detenidamente las instrucciones y familiaricese con la máquina. - Page 4 • Motor Off •. Arrêt Du Moteur • Parar El Motor • Use In Well Ventilated Area •. A Utiliser Dans Un Endroit Bien Ventilé • Usar En Una Área Bien Ventilada • Do Not Use In Flammable Areas •. Ne Pas Utiliser Dans Des Ambiances Comportant Un Risque D’incendie •...
-
Page 5: Hearing Hazard Warning
• Repairs Are To Be Done By An Authorized Dealer Only •. Les réparations ne peuvent être exécutées que par un distributeur agréé • Las Reparaciones Deben Ser Efectuadas Únicamente Por Un Distribuidor Autorizado • Diamond Blade •. Disque diamanté •... -
Page 6: Dust Warning
DUST WARNING Cutting, especially when DRY cutting, generates dust that comes from the material being cut, which frequently contains silica. Silica is a basic component of sand, quartz, brick clay, granite and numerous other minerals and rocks. Exposure to excessive amount of such dust can cause: •... -
Page 7: Decal Descriptions And Locations
DECALS & LOCATIONS ETIQUETAS Y SU UBICACIÓN AUTOCOLLANTS ET LEURS EMPLACEMENTS 542 19 07-40 (x2) Location: Both Sides of Pan 504 04 02-01 (x2) Location: Front Top Corner of Blade Guard 542 19 07-36 Location: Rip Guide 542 19 07-39 Location: Front of Pan P/N 542 04 63-27* Location: Motor Assembly... -
Page 8: Safety First
SAFETY FIRST! WARNINGS DO’s AND DO NOT’s WARNING: .FAILURE TO COMPLY WITH THESE WARNINGS AND OPERATING INSTRUCTIONS COULD RESULT IN DEATH OR SERIOUS BODILY INJURY. read this entire operator’s manual before operating this machine. Understand all warnings, instructions, and controls. keep all guards in place and in good condition. -
Page 9: Safety Warnings - Dos & Do Nots
This saw was designed for certain applications only. DO NOT modify this saw or use for any application other than for which is it was designed. If you have any questions relative to its application, DO NOT use the saw until you have written Husqvarna Construction Products and we have advised you. Husqvarna Construction Products... -
Page 10: Figures: Figure 1
FIGURE 1 Assembly Component Identification Major Assemblies in Shipping Carton Pan Guides Cutting Head Assembly: Includes Water Pan Stops Tube Assembly (L)} Drain Plug Frame Assembly Bearing Cap & Fasteners Water Pan Assembly TIle Saw Wrench (15/16” x 9/16” x 1/2”) Conveyor Cart Assembly (4) with Rip Fence Locking Knob (S) included. -
Page 11: Features
The motor and pump power cords are securely Tools: Rip Guide comes standard on all tile saws. mounted directly into the motor housing. See Tile Cutting Accessories on page 19. • The removable Drain Plug (C) at the front end of the pan permits easy coolant draining and quick sludge (For information or availability of other accessories con- clean out. The Water Pan (2) is removable for easy tact your Husqvarna supplier.) cleaning. • The free-rolling Conveyor Cart (4) is aligned for Blade Capacity: Rim Ø 10” (254mm) - bore 5/8” straight, smooth cuts. The Backstop with ruler allows (15,9mm). fast mounting and adjustment of the Rip Fence (S) Profile Wheel: Rim Ø 6” (152mm) - bore 5/8” and optional accessories. The Cart comes standard (15,9mm). - Page 12 For the best results, always use genuine Husqvarna diamond blades. Contact your Water Pump Assembly (5) Set-up: nearest dealer to select the correct blade for your spe- Remove the Water Pump (H), Hose Barb (J), cific cutting needs.
-
Page 13: Operating Procedure
Raise the Blade Guard (M) to fully up and tighten OPERATING PROCEDURE the wing nut on the side to hold it in the raised position. WARNING: Read the Operating Procedure Remove the Arbor Nut (O) and the Outer Blade completely before operating your tile saw. Flange (P). -
Page 14: Figure 3
10”, 8” or 6” blade. Loosen the Set Collar (5/32” hex key), the The TS 250 XL is shipped standard set-up for a 10” Position Limiter (9/16” wrench) and the four diameter blade. To change the setting, locate the capscrew (4) fasteners (1/2”... -
Page 15: Profile Wheel Set-Up And Use
Simple daily maintenance and care will add to the life and The TS 250 XL is designed for use with a Husqvarna® 6” productivity of your saw. After each day’s use: CLEAN Profile Wheel, such as P/N 542 62 10-81* (3/8” Radius) THE MACHINE!! or 542 62 10-82* (1/2”... -
Page 16: Figure 4
1. Stop Sawing, then address and phone numbers) Contact your authorized 2. Disconnect Electrical Plug from Outlet, then Husqvarna® dealer concerning maintenance and re- 3. Remove the Pump, then 4. Back Flush. V-Belt Tensioning with Cam Adjustment: Back flushing is done by forcing water into the pump discharge and out through the screen. -
Page 17: Tile Cutting Accessories
FOLDING STAND: P/N 542 05 10-41* - This stable, one ANGLE GUIDE : P/N 542 05 10-20* - This is a non- piece stand brings a Husqvarna® tile saw to standing adjustable miter used to quickly position the tile at level for ease of work. -
Page 18: Wiring Diagrams
Diagram 1: Wiring Diagram 542 20 30-79, 1.5HP, 115V/60/1... -
Page 19: Wiring Diagrams
Diagram 2: Wiring Diagram 542 00 06-05, 1.5 HP, 115V/208-230/60/1... - Page 20 NOTES: NOTAS: REMARQUE :...
-
Page 21: Warranty
Customer Service: 913-928-1300 Customer Serv. Fax: 913-438-7938 www.husqvarna.com Please record the Date of Purchase and the Serial Number, the Model Number of the equipment and the Date of Purchase of your equipment in the space below. When ordering service items, please have this information available.