Runco Q-1500d Quick Setup Manual

Model Q-1500d and Q-1500d Ultra
Table 1. Installation Overview
Step Procedure
1
Choose a location for the projector
2
Install CineWide lens mounting assembly (stationary base plate or AutoScope lens motor – optional)
3
Mount the projector
4
Mount the Dimension Digital Controller
5
Connect the Dimension Digital Controller to the projector
Connect other external equipment to the Dimension Digital Controller (optional):
• Audio processor or secondary display device
• Control system interface (RS-232)
6
• 12-volt trigger-activated equipment (retractable screens or screen masking)
• External IR repeater
• Network hub, router or gateway (Ethernet)
7
Connect signal sources to the Dimension Digital Controller
8
Connect system components to AC power
9
Power up the system and perform optical alignment procedures (refer to Table 2)
Display calibration — Dimension Digital Controller: adjust the following for each input and display
mode (resolution and frame rate); save settings when finished:
• Aspect ratio
10
• Contrast
• Tint
• White Balance
Q-1500d Series LED Home Theater Projection System Quick Setup Guide
QuantumColor Series
LED Home Theater Projection System

Quick Setup Guide

For Details, Refer to this page
Installation/Operation Manual
21
29
34
35
36
38
43
48
49
66
• Brightness
• Color level
• Sharpness

Connecting the Dimension Digital Controller to the Projector

in the Q-1500d Series
RJ-11
to DB-9
Adapters
(provided)
RS-232
Communication
Cables (provided)
Projector Lens Adjustments
Intake Side
Projection
Lens
Zoom
Tab
Projection
Lens
Zoom
Tab
Page 1
PRIMARY
SECONDARY
Primary and Secondary
Display Control
Pri. Display Control Sec. Display Control
3D SYNC 3D SYNC TRIGGERS TRIGGERS US US
IR IR
1 1 2 2 3 3
Component / SCART Component / SCART HDMI Out
HDMI HDMI HDMI 5 HDMI 5 HDMI 7 HDMI 7 To Sec. Display
HD1 HD1 Y Y Video 1 Video 1 Video 2 Video 2
HDMI Out
To Secondary
Display
Pb Pb Pr Pr Video 3 Video 3
DisplayPort DisplayPort r r HD2 HD2 HDMI 2 HDMI 2 HDMI 4 HDMI 4 HDMI 6 HDMI 6 HDMI 8 HDMI 8 Ethernet Ethernet HDMI Out HDMI Out HDMI Out
Audio Only Audio Only To Pri. Display
• PROJECTION LENS
Available in three versions: standard throw range (1.94:1 to
2.40:1), short throw range (1.64:1 to 1.86:1) and long throw range
(Q-1500d Ultra only; 2.52:1 to 4.00:1).
Exhaust Side
• LENS LOCK
Freezes the zoom and lens shift settings to keep the projector
Primary
images aligned over time. Use the supplied, 5.0-mm Hex wrench
Lens Optical
Horizontal Lens Shift
to lock the lens position. (Turn clockwise two or three turns.)
Lock Engine
Control
Vertical Lens Shift
Focus
Control
Ring
Secondary
Lens Horizontal Lens Shift
Optical
Lock Control
Engine
• HORIZONTAL AND VERTICAL LENS SHIFT CONTROLS
Vertical Lens Shift
Insert the supplied, 5.0-mm Hex wrench into the opening and turn
Focus
Control
Ring it as needed to shift the lens in the desired direction.
• FOCUS RING
Rotate this to focus the projected image.
• ZOOM TAB
Rotate this to change the projected image size.
HDMI Cables
(not provided)
HDMI Out
To Primary
Display
Do not attempt any primary lens adjustments
WARNING
when the lenses are locked. Doing so may cause
damage to the zoom or lens shift mechanisms.
020-1091-02 Rev. A (March 2014)