Timer Recording; Note For Timer Recording & Otr - FUNAI DV220FX4 Owner's Manual

Timer Recording

VCR
Press first.
VHS VHS VHS VHS VHS
1
SETUP
Press , use
"TIMER PROGRAMMING".
Then, press to go to next step.
B TIMER PROGRAMMING
SATELLITE LINK
AUTO REPEAT
CLOCK SET
LANGUAGE SELECT
2
Use / to select an
empty program number. Then,
press to go to next step.
3
Use / to select
"ONCE", "DAILY" (Mon-Fri), or
"WEEKLY". Then, press
to go to to go to next step.
4
Use / to select the
desired month. Then, press
to go to the next step.
Then, repeat procedures above to select the day, start
time, end time, and "L1" or "L2" as well.
5
Use / to select
recording speed. Then,
CLEAR
to remove the MENU .
press
To set another program after step 5, press
Then, repeat procedures from steps 2 through 5.
You can program the unit to record up to 8 programs,
and up to 1 year in advance.
6
TIMER SET
Press to set the timer standby mode.
The [TIMER REC] indicator on this unit lights up and
the unit goes to the DVD mode.
Note: • To go back one step, press [s [ [ ] during steps 3 to
5.
• Select "L1" or "L2" to activate rear input jacks or
front input jacks accordingly.
EN
RECORDING
/ to select
- M E N U - TIMER PROGRAMMING
PROG 12345678
DATE
[OFF]
START TIME
END TIME
L1/L2
REC SPEED
Available program
number blinks.
PROGRAM NUMBER 1
DATE – – / – –
START TIME – – : – –
END TIME – – : – –
L1/L2 – –
REC SPEED – –
PROGRAM NUMBER 1
B ONCE
DAILY
WEEKLY
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE 1 0 / 0 2 TUE
START TIME – – : – –
END TIME – – : – –
L1/L2 – –
REC SPEED – –
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE 1 0 / 0 2 TUE
START TIME 0 7 : 3 0
END TIME 0 8 : 3 0
L1/L2 L1
REC SPEED SP
B SP
SLP
]
To Check, Correct or Cancel a Timer Prog g g To Check, Correct or Cancel a Timer Program To Check, Correct or Cancel a Timer Program
1) Press [TIMER SET], and then press [VCR
remote control.
2) Repeat procedures in step 1 above.
3) Use [K / L] to select the program number you want
to check. The details of the program you select will
appear on the TV screen.
Use [s / B] to go to the digit you want to change.
Then, use [K / L] to enter the correct numbers.
You can cancel the entire program by pressing [s]
while the program number blinks.
4) Press [CLEAR] to exit.
5) Press [TIMER SET] to return to the timer standby
mode.
To Cancel a Timer Recording in Progress To Cancel a Timer Recording in Progress
– –
– – Press [C A] on the unit.
Note for Timer Recording & OTR
• If a power failure occurs or the cassette tape does not
have the erase-protection tab,
the [TIMER REC] indicator blinks and timer recording
cannot be performed.
• If there is a power failure occurred or the unit is
unplugged for more than 30 seconds, clock setting and
– –
all programmed timer recordings will be lost.
– –
• If a cassette tape runs out before an OTR or a timer
recording is finished, the unit ejects the cassette tape.
After an OTR or a Timer Recording Has After an OTR or a Timer Recording Has After an OTR or a Timer Recording Has
Been Set, This Unit Op p p Been Set, This Unit Operates as Follows: Been Set, This Unit Operates as Follows:
• Press [TIMER SET] on the remote control or [C A] on
the unit, then press [VCR
PM
PM
function again.
• To cancel the timer standby mode, press [TIMER SET] on
the remote control or [C A] on the unit, then press [VCR
. ] to activate the VCR function again.
When an OTR or a Timer Recording is Completed. When an OTR or a Timer Recording g g When an OTR or a Timer Recording is Completed.
• If timer programmings are left on the VCR, the unit will
switch to the DVD mode and then the VCR will go standby
for the next timer recording. ( All the VCR functions will be
unavailable.) If auto power off has been in effect, however,
both DVD and VCR will go to standby mode.
• All the DVD functions are available while the VCR is in
OTR, Timer standby, or Timer Recording mode.
• The [TIMER REC] indicator blinks if there are no more
timer programs.
• Press [C A] on this unit or [TIMER SET] on the remote
control to use the VCR when the unit is turned off.
To Use the DVD Play y To Use the DVD Player During Timer To Use the DVD Player During Timer
Recording or While the [TIMER REC] Recording or While the [TIMER REC] g
Indicator is On or Blinking. g g Indicator is On or Blinking. Indicator is On or Blinking.
• Press [y y ] to turn On the unit. Press [DVD
Remote Control to choose DVD mode. Then continue
with the other DVD features as described in this manual.
] on the
g g g g
g g g
Operates as Follows: p
] to activate the VCR
ng is Com g
layer During Timer y g g g
g. g
] on the
g gram
p p p pleted.
21