Kenmore 106.6110 Series Use & Care Manual page 10

Freezer Door
1. Remove freezer handle assembly as shown. Keep all parts
together. See Graphic 3.
2. Remove door hinge hole plug. Move to opposite side as
shown in Graphic 4.
3. Remove door handle sealing screws. Move to opposite side
of freezer door as shown in Graphic 7.
4. Remove door stop. Move to opposite side of freezer door as
shown in Graphic 6.
5. Remove the hinge pin from the top hinge. Turn the hinge
over so that it is pointing in the opposite direction and
reinsert the hinge pin into the top hinge. See Graphic 2.
NOTE: For some models, when you reverse the door swing, a
top hinge cover (for the left-hand side) is provided for your
convenience.
6. Position handle on opposite side of freezer door. Assemble
handles on door as shown in Graphic 3.
7. Tighten all screws. Set aside freezer door until hinges and
refrigerator compartment door are in place.
Refrigerator Door
1. Remove refrigerator handle assembly as shown. Keep all
parts together. See Graphic 5.
2. Remove door hinge hole plug from refrigerator door. Move
to opposite side hinge hole as shown in Graphic 4.
3. Remove door handle sealing screws. Move to opposite side
of refrigerator door as shown in Graphic 7.
4. Remove door stop. Move to opposite side of refrigerator
door as shown in Graphic 6.
5. Position refrigerator handle on opposite side of the
refrigerator door as shown in Graphic 5. Drive the top two
screws in handle first. Align the lower portion of the handle
and fasten it with the setscrew.
6. Tighten all screws. Set aside refrigerator door until bottom
hinge is installed on refrigerator.
NOTE: For 21 cu ft models, transfer both the bottom hinge
assembly and the leveling foot to the opposite side.
Cup Style Handles - Recessed into the Door
(on some models)
Cabinet
1. Remove the hex head screws from handle side and move
them to opposite side. See Graphic 1-1.
2. Remove cabinet hinge hole plugs from the cabinet top and
move them to opposite side hinge holes as shown in
Graphic 1-2.
Doors
1. Remove door hinge hole plug from top of freezer door.
Move to opposite side as shown in Graphic 3.
2. Remove door stop from both the freezer and refrigerator
doors and move to the other side. See Graphic 5.
10
Replace Doors and Hinges
NOTES:
Graphic may be reversed if door swing is reversed.
Provide additional support for the doors while the hinges are
being moved. Do not depend on the door magnets to hold
the doors in place while you are working.
1. Replace the parts for the bottom hinge as shown. Tighten
screws. Replace the refrigerator door.
NOTE: For 21 cu ft models, install both the bottom hinge
assembly and the leveling foot on the opposite side.
2. Assemble the parts for the center hinge as shown and
tighten all screws. See Center Hinge graphic. Replace the
freezer door.
3. Assemble the parts for the top hinge as shown in the Top
Hinge graphic. Do not tighten the screws completely.
4. Line up the doors so that the bottom of the freezer door
aligns evenly with the top of the refrigerator door. Tighten
all screws.
Final Steps
1. Check all holes to make sure that hole plugs and screws are
in place. Reinstall top hinge cover. See Top Hinge graphic.
Style 1 - On the left-hand side of the base grille there is a
removable tab which is a bottom hinge hole plug. Break off
the tab from the base grille and insert the bottom hinge hole
plug into the bottom hinge holes. See Base Grille graphic.
2. Replace the base grille. See Base Grille graphic.
3. Plug in refrigerator or reconnect power.
4. Reset the controls. See "Using the Controls."
5. Return all removable door parts to doors and food to
refrigerator.