Page 1
2006 by Harbor Freight Tools ® . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions, please call 1-800-444-3353.
Do not spray flammable liquid in a confined area or towards a hot surface. Spray area must be well ventilated. Do not smoke while spraying or spray where spark or flame is present. REV 11/06 SKU 94355 For technical questions, please call 1-800-444-3353 PAGE 2...
Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. Protect others in the work area from debris such as chips and sparks. Provide barriers or shields as needed. SKU 94355 For technical questions, please call 1-800-444-3353 PAGE 3...
Maintain tools with care. Properly maintained tools with a sharp cutting edge are less likely to bind and are easier to control. Do not use a damaged tool. Tag damaged tools “Do not use” until repaired. SKU 94355 For technical questions, please call 1-800-444-3353 PAGE 4...
SPECIFIC SAFETY RULES AND PRECAUTIONS Maintain labels and nameplates on the Air Compressor. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement. DANGER! This Air Compressor is NOT equipped with and should not be used “as is”...
Page 6
It must be under stood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. SAVE THESE INSTRUCTIONS SKU 94355 For technical questions, please call 1-800-444-3353 PAGE 6...
The plug and outlet should look like those in the following illustration. (See Figure A.) THIS PRODUCT USES A 3-PRONG PLUG 120 VOLT, GROUNDED, ELECTRICAL OUTLET FIGURE A SKU 94355 For technical questions, please call 1-800-444-3353 PAGE 7...
Double insulated tools may be used in either of the 120 volt outlets shown in the following illustration. (See Figure B.) THIS PRODUCT DOES NOT USE A 2-PRONG PLUG 120 VOLT, GROUNDED, ELECTRICAL OUTLETS FIGURE B SYMBOLOGY FIGURE C SKU 94355 For technical questions, please call 1-800-444-3353 PAGE 8...
When unpacking, check to make sure all the parts shown on the Parts List on page 14 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible.
CAUTION! Always make sure the Pressure Switch (57) of the Air Compressor is in its “OFF” position and the unit is unplugged from its electrical outlet prior to performing any service, maintenance, or changing accessories on the Compressor. SKU 94355 For technical questions, please call 1-800-444-3353 PAGE 10...
Page 11
Allow about 15 minutes for the running Air Compressor to build up sufficient air capacity in its Air Tank (3). Then use the Pressure Regulator Knob (14) to increase or decrease the air flow to the pneumatic tool being used. (See Figure D.) SKU 94355 For technical questions, please call 1-800-444-3353 PAGE 11...
Do not use damaged equipment. After each use, open the water Drain Valve (4) under the Air Tank (3) to drain out the moisture. (See Figure E.) SKU 94355 For technical questions, please call 1-800-444-3353 PAGE 12...
ASSUMES ALL RISKS AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 94355 For technical questions, please call 1-800-444-3353 PAGE 13...
Bleed line by moving pressure switch lever to OFF position before restarting. If bleeder valve does not open, replace bleeder valve. Have a qualified service technician clean or replace motor. SKU 94355 For technical questions, please call 1-800-444-3353 PAGE 14...
Washer Screw (ST4 x 10) Head Gasket Lower Cover Air Hose NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 94355 For technical questions, please call 1-800-444-3353 PAGE 15...
90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that for a period of ninety days from date of purchase that the motor is free of defects in materials and workmanship.