Table of Contents
Advertisement
Connecting Wires to Terminals
⁄
Do not remove the cap
To USB device
when you do not use the
USB connector
USB cable. The connector
(0.8 m (2.7 ft))
will cause the unit to
malfunction if it gets in
touch with any metallic
part of the vehicle.
Microphone input
Microphone
(Accessory5)
Fuse (10A)
Wiring harness
(Accessory1)
White
White/Black
Gray
Gray/Black
Green
Green/Black
Purple
Purple/Black
If no connections are made, do not let the wire come out from the tab.
Blue/White (Power control wire)
When using the optional power amplifier, connect this wire to its power
control terminal.
P.CONT
Depending on what antenna you are using, connect either to the control
Blue (Antenna control wire)
terminal of the motor antenna, or to the power terminal for the booster
ANT.
CONT
amplifier of the film-type or short pole type antenna.
(Max. 300mA, 12V)
Brown (Mute control wire)
To connect the Kenwood navigation system, consult your navigation
manual.
MUTE
Orange / White (Dimmer control wire)
To car light control switch
ILLUMI
Light Blue/Yellow (Steering remote
control wire)
To use the steering wheel remote control feature, you need to an
REMOTE
exclusive remote adapter (not supplied) matches your car is required.
CONT
STEERING
WHEEL
REMOTE
INPUT
Car fuse
box
Red (Ignition wire)
ACC
Yellow (Battery wire)
Black (Ground wire) · (To car chassis)
83
|
KDC-X996/ KDC-BT952HD
Rear output
R
L
Front output
Sub Woofer output
Antenna Cord
FM/AM antenna input
R
L
AUX input (Stereo)
Use the mini-plug which is stereo type
and does not have any resistance.
(3.5 mm (1/8") ø)
To SiriusXM Connect Vehicle Tuner (optional accessory)
To front left speaker
To front right speaker
To rear left speaker
To rear right speaker
Ignition key
switch
Car fuse box
(Main fuse)
+
–
Battery
Installing/Removing the unit
non-Japanese cars
Bend the tabs of the mounting
sleeve with a screwdriver or the
like and attach it in place.
⁄
• Make sure that the unit is installed securely in place. If the
unit is unstable, it may malfunction (for example, the sound
may skip).
Japanese cars
1
Remove the hard rubber frame with reference to
<Removing the hard rubber frame>.
2
Align the holes in the unit (two locations on each
side) with the vehicle mounting bracket and secure
the unit with the accessory screws.
T
N
T/N
T
N
T: Toyota cars
N: Nissan cars
8 mm
8mm
MAX.
MAX.
3
4
ø5mm
ø5mm
Accessory3...for Nissan car
Accessory4...for Toyota car
¤
CAUTION
Install this unit in the console of your vehicle.
Do not touch the metal parts of this unit during and
shortly after use of the unit. Metal parts such as the
heat sink and enclosure become hot.
Removing the hard rubber frame
1
Engage the catch pins on the removal tool and
release the two locks on the upper part of frame.
Lift up and pull the frame forward as shown in the
figure.
Lock
Catch
Accessory2
Removal tool
2
When the upper part of frame is removed, remove
the lower part of frame.
⁄
• The frame can be removed from the bottom side in the
same manner.
Removing the Unit
1
Remove the hard rubber frame with reference to
<Removing the hard rubber frame>.
2
Detach the faceplate.
3
Insert the two removal tools deeply into the slots
on both sides as shown.
4
Lower the removal tool toward the bottom, and
then pull out the unit halfway while pressing the
removal tool towards the inside.
Accessory2
¤
• Be careful to avoid injury from the catch pins on the
removal tool.
5
Pull the unit all the way out with your hands, being
careful not to drop it.
|
English
84
Hide quick links:
Advertisement
Table of Contents
