Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Hoover Celebrity S3237
Summary of Contents for Hoover Celebrity S3237
-
Page 2: Table Of Contents
Replacing Headlight ..... .19-20 Storing Cleaner.......I 2 @ 1975, 1978,1980 1992 The Hoover Company... -
Page 3: Important Safeguards
Close supervision is necessary when any appliance is used by or near children. Do not allow vacuum cleaner to be used as a toy or to run unattended at any time. Keep hands, feet, loose clothing, and hair away from rotating agita- tor. - Page 4 A. Canister cleaner B. Electronic power nozzle C. Throw away bag D. Tools with tool storage rack, extension wands (Model S3237 has two sets of wands), and hose. The cleaner assembled will look like the drawing below.
- Page 5 15. Spring Latch locks extension wands. 16. Extension Wands connect to hose and electronic power nozzle or cleaning tools. Model S3237 - use curved wand and straight wand with cord clips when using electronic power nozzle; use extra set of wands with cleaning tools.
-
Page 6: How To Assemble
21. Suction Regulator should be opened for easy cleaning of some types of carpet, lightweight flexible rugs and lightweight draperies, 22. Cord Clips clip nozzle cord to extension wands. 23. Nozzle Cord Connection to Handle is made by plugging nozzle cord into receptacle underneath the handle. -
Page 7: Power Nozzle
. ..-- 2. Attach electronic power nozzle Note: For most convenient use with electronic power nozzle, connect curved and straight wand with cord clips to nozzle. Attach the electronic power noz- zle at the end of the straight wand by fitting the button projection on the nozzle connector into the opening at the end of the wand. -
Page 8: How To Use
3. Attach tool storage rack To attach tool storage rack, in- sert rear projections of rack into the two rear slots on top of the cleaner. Snap front middle sec- tion into place. How to use Two speed switch Your cleaner is equipped with a switch for “Hi” and “Lo” speed. Use “Lo”... - Page 9 Swiveling handle and wands The handle and wands conveniently swivel to the right for ease in clean- ing under low furniture. To swivel handle and wands, twist handle to the right. The handle and wands should “click” out of the original position. To swivel handle and wands back to the original position, twist handle to the left.
- Page 10 “CHECK BELT” light The electronic power nozzle auto- matically monitors its belt condi- tion. When the belt needs replac- ed, the red “CHECK BELT” light will come “ON” and remain “ON” until the belt is replaced. To replace belt, refer to “The belt”...
-
Page 11: Cleaning Tools
OPEN Select the proper cleaning tool The cleaning tools have many uses. Select the tool best suited for the cleaning task from the descriptions below. Adjust the Suction Regulator to select the amount of suction appropriate to the cleaning task. adjustment The electronic power nozzle ad- .justs automatically to the correct... - Page 12 The headlight bulb should provide years of normal use; however, the motor will not operate if the bulb burns out. For bulb replacement use a 15 watt lamp only. Use Hoover part number 16113 or Sylvania 15T7DC bulb. Litho USA 11-82...
-
Page 13: Power Cord
To use the cleaner with tools dis- connect the nozzle from the ex- tension wands. (For Model S3237, leave the nozzle assembl- ed to the wands and only discon- nect nozzle cord and curved wand from handle, since two ad- ditional wands are provided for use with tools. -
Page 14: Maintenance
Maintenance The following sections are concerned with proper maintenance of the cleaner. Familiarize yourself with these home maintenance tasks and keep this owner’s manual in a convenient place where you can refer to it when needed. Proper use and care of your cleaner will assure continued cleaning effectiveness. - Page 15 Where to buy bags Bags may be purchased from your local Authorized Hoover Dealer or from a Hoover Factory Service Center. When ordering bags, be sure to give the model number of your cleaner. What bags to buy Use HOOVER bag type H with this cleaner.
-
Page 16: Clearing Obstructions
/-’ CoNNECTOR Adjust bag around the motor housing and open the folds of the bag to allow the bag to properly fill. Make sure all four folds are open. Note: A bag that does not ex- pand properly may restrict air flow. -
Page 17: Secondary Filter
There are other belts manufactured that are similar in shape and size but are not designed for the HOOVER electronic power nozzle. Such belts do not operate the agitator correctly and may create stress which could damage your electronic power nozzle. - Page 18 MOTOR PULLEY AGITATOR PULLEY SiOT PR‘OJECTION Return nozzle to original position and lift up back of nozzle cover. Then remove cover, rotating it forward and lifting it off. To remove the agitator, position your hand underneath the nozzle base at the agitator opening and push up the belt end of the agita- tor.
-
Page 19: And Brush Roll
Rotate agitator by hand. If brushes do not touch edge of card, all four brushes and brush roll should be replaced to maintain cleaning effectiveness. When replacing agitator brushes and brush roll, ask for HOOVER part No. 48445017 and part No. 48418401. - Page 20 brushes and brush roll Disconnect cleaner from electri- cal outlet and disconnect elec- tronic power nozzle from exten- sion wands. Remove nozzle cover, agitator and belt following directions in “How to replace belt” section. 1. Hold agitator as shown. Turn end plates in opposite directions until one end plate comes off.
- Page 21 Note: The headlight bulb is part of the electronic circuit and the elec- tronic power nozzle motor will not operate if the bulb is burned out. The bulb must be replaced with a 15 watt bulb. Use Hoover part number 16113 or Sylvania 15l7DC bulb.
- Page 22 Turn nozzle over and unscrew the 2 Phillips head screws from the nozzle base. The cover attaches at the front of the nozzle. Place the notched edge at the front of the cover into the groove in the nozzle base. Return nozzle to original position and lift up back of nozzle cover.
-
Page 23: If You Have A Problem
Center to find your nearest Authorized Warranty Service Dealer. For service under warranty, follow the instructions in the Warranty provided with this product. Do not send your cleaner to The Hoover Company in North Canton for service, as this will result in delay. -
Page 24: Energy Saving Tips
The addition of lubricant could cause damage. Therefore, do not add lubricant to either motor bearing. The agitator is equipped with two ball bearings that should be lubricated periodically. This should be done by a Hoover Factory Service Center or an Authorized Hoover Warranty Service Dealer. Energy saving tips 1. - Page 25 For optimum cleaning performance and safety, study and follow your Owner’s Manual - keep it in a handy and safe place for future reference. THE HOOVER COMPANY, NORTH CANTON, OHIO 44720 R 3 9 - 8 3 S3237/39 butts. Litho USA...