Front Panel Information Display - Harman Kardon AVR120 Service Manual

AVR120

Front Panel Information Display

D
DTS
MP3
PCM
Bitstream Indicators
DTS Mode Indicator
Dolby Digital Indicator
Dolby Pro Logic II Indicator
Dolby 3 Stereo Indicator
Main Information Display
DSP Mode Indicator
VMAx Mode Indicators
Bitstream Indicators: When the input is a
digital source, one of these indicators will light to
display the specific type of data signal in use.
DTS Mode Indicator: This indicator lights
when a DTS-encoded source is playing.
Dolby Digital Indicator: This indicator
lights when a Dolby Digital source is being
played.
Dolby Pro Logic II Indicator: This indica-
tor lights when the Dolby Pro Logic II mode has
been selected.
NOTE: It is possible to see the Dolby
Pro Logic II indicator lit simultaneously with the
Dolby Digital indicator, even though the Dolby
Digital surround mode has been selected. This is
due to the specifications for Dolby Digital pro-
cessing, which require that the Dolby Pro Logic II
mode apply any time a 2-channel Dolby signal
is detected. If you desire 5.1-channel audio,
check the audio settings in the menus for both
your DVD player and your DVD disc to make
sure that a 5.1-channel Dolby Digital sound
track is available and has been selected.
Dolby 3 Stereo Indicator: This indicator
lights when the Dolby 3 Stereo mode has been
selected.
Main Information Display: This display
shows messages relating to the status, input
source, surround mode, tuner, volume level or
other aspects of the AVR 120's operation.
OPT 123 COAX 123 ANALOG
D PL II 3ST
Logic 7 Mode Indicators
Preset Number/Sleep Timer
Night Mode Indicator
Speaker/Channel Input Indicators
Preset Indicator
Sleep Indicator
Memory Indicator
Stereo Indicator
DSP Mode Indicator: This indicator lights
when any of the surround modes created by
Digital Signal Processing, or DSP are in use.
These modes include Hall 1, Hall 2, Theater and
5-Channel Stereo.
VMAx Mode Indicators: This indicator
lights when the VMAx mode is in use. VMAx F
appears when the Far Field VMAx mode is
selected; VMAx N appears when the Near
Field VMAx mode is selected. (See page 22 for
a description of the VMAx modes.)
Logic 7 Mode Indicators: These indica-
tors light when the Logic 7 mode is in use.
LOGIC 7C appears for the Cinema version
of Logic 7; LOGIC 7M appears for the
Music version of Logic 7. (See page 22 for a
description of the Logic 7 modes.)
Preset Number/Sleep Timer: When the
tuner is in use, these numbers indicate the spe-
cific preset memory location in use. (See page
26 for more information on preset stations.)
When the Sleep function is in use, these num-
bers show how many minutes remain before
the unit goes into the Standby mode.
Night Mode Indicator: This indicator
lights when the AVR 120 is in the Night mode,
which preserves the dynamic range of digital
program material at low volume levels.
Speaker/Channel Input Indicators: These
indicators are multipurpose, indicating either the
speaker type selected for each channel or the
AUTO TUNED ST MEM PRESET
SLEEP
KHz
MHz
DSP VMAx NF LOGIC 7 CM
incoming data-signal configuration. The left,
center, right, right surround and left surround
speaker indicators are composed of three boxes,
while the subwoofer is a single box. The center
box lights when a "small" speaker is selected,
and the two outer boxes light when "large"
speakers are selected. When none of the boxes
are lit for the center, surround or subwoofer
channels, no speaker has been assigned to one
of those positions. (See page 17 for more infor-
mation on configuring speakers.) The letters
inside each of the center boxes display active
input channels. For standard analog inputs, only
the L and R will light, indicating a stereo input.
When a digital source is playing, the indicators
will light to display the channels being received
at the digital input. When the letters flash, the
digital input has been interrupted. (See pages
18–19 for more information on the Channel
Indicators.)
when the tuner is in use to show that the
Preset Number/Sleep Timer
the station's preset memory number. (See page
26 for more information on tuner presets.)
the Sleep function is in use. The numbers in the
Preset Number/Sleep Timer Indicators will show
the minutes remaining before the AVR 120
goes into the Standby mode. (See page 21 for
more information on the Sleep function.)
7 FRONT PANEL INFORMATION DISPLAY
harman/kardon
C
L R
NIGHT
SL SR
LFE
Tuned Indicator
Auto Indicator
Analog Input Indicator
Coaxial Digital Input Indicators
Optical Digital Input Indicators
Preset Indicator: This indicator lights
is showing
Sleep Indicator: This indicator lights when