Sony STR-KM5000 Service Manual page 48

STR-KM5000
DIGITAL AB BOARD IC1501 ADSST-AVR-1115 (DSP)
Pin No. Pin Name
1 VDDINT
CLKCFG0,
2, 3
CLKCFG1
BOOTCFG0,
4, 5
BOOTCFG1
6 GND
7 VDDEXT
8 GND
9 VDDINT
10 GND
11 VDDINT
12 GND
13 VDDINT
14 GND
15 FRAG0
16 FRAG1
17 AD7
18 GND
19 VDDINT
20 GND
21 VDDEXT
22 GND
23 VDDINT
24 to 26 AD6 to AD4
27 VDDINT
28 GND
29, 30 AD3, AD2
31 VDDEXT
32 GND
33, 34 AD1, AD0
35 XWR
36, 37 VDDINT
38 GND
39 XRD
40 ALE
41 to 43 AD15 to AD13
44 GND
45 VDDEXT
46 AD12
47 VDDINT
48 GND
49 to 52 AD11 to AD8
53 A16
54 VDDINT
55 GND
56, 57 A17, A18
58 GND
59 VDDEXT
60 VDDINT
61 GND
62 PF_CE
63 SPI_MAS
64 DPSOA
65 DPSOB
66 VDDINT
48
I/O
- Power supply terminal (+1.2V)
I Clock frequency setting terminal
I Boot mode setting terminal for DSP
- Ground terminal
- Power supply terminal (+3.3V)
- Ground terminal
- Power supply terminal (+1.2V)
- Ground terminal
- Power supply terminal (+1.2V)
- Ground terminal
- Power supply terminal (+1.2V)
- Ground terminal
O Interrupt status output to the system controller
I PLL lock error signal and data error fl ag input terminal
I/O Two-way data bus and address signal output with S-RAM
- Ground terminal
- Power supply terminal (+1.2V)
- Ground terminal
- Power supply terminal (+3.3V)
- Ground terminal
- Power supply terminal (+1.2V)
I/O Two-way data bus and address signal output with S-RAM
- Power supply terminal (+1.2V)
- Ground terminal
I/O Two-way data bus and address signal output with S-RAM
- Power supply terminal (+3.3V)
- Ground terminal
I/O Two-way data bus and address signal output with S-RAM
O Data write enable signal output to the S-RAM
- Power supply terminal (+1.2V)
- Ground terminal
O Read strobe signal output to the S-RAM
O Address latch enable signal output terminal
I/O Two-way data bus and address signal output with S-RAM
- Ground terminal
- Power supply terminal (+3.3V)
I/O Two-way data bus and address signal output with S-RAM
- Power supply terminal (+1.2V)
- Ground terminal
I/O Two-way data bus and address signal output with S-RAM
O Address signal output to S-RAM
- Power supply terminal (+1.2V)
- Ground terminal
O Address signal output to S-RAM
- Ground terminal
- Power supply terminal (+3.3V)
- Power supply terminal (+1.2V)
- Ground terminal
I/O Chip enable signal input/output terminal
O Master/slave selection signal output terminal
O PCM audio signal (front L/R) output to the D/A converter
O PCM audio signal (surround L/R) output to the D/A converter
- Power supply terminal (+1.2V)
Description
Not used
Not used
Not used
Not used
"L": active Not used
"L": active Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
"L": DSP is master Not used