Download Print this page

Honeywell Round T8775A Installation Instructions

Honeywell the digital round non-programmable thermostat installation instructions
Hide thumbs Also See for Round T8775A:

Advertisement

Honeywell
T8775A,C
TheDigitalRound
TM
Non-Programmable Thermostats
The T8775A,C Thermostats provide single-stage
temperature
control for 24V systems. The
T8775A,C models include a thermostat, wallplate
(for wiring and mounting thermostat), mounting
screws, wall anchors, and a 4074 FAB resistor.
MERCURYNOTICE
If this control is replacing a control that
contains mercury in a sealed tube, do not
place your old control in the trash.
Contact your local waste management
authority for instructions regarding
recycling and the proper disposal of an old
control containing mercury in a sealed
tube.
INSTALLATION
When Installingthis Product...
1.
Read these instructions carefully. Failure to
follow them could damage the product or
cause a hazardous condition.
2.
Check the ratings given in the instructions
and on the product to make sure the product
is suitable for your application.
3.
installer must be a trained, experienced
ser-
vice technician.
4.
After installation is complete, check out prod-
uct operation as provided in these instruc-
tions.
z_ CAUTION
Electrical Shock or Equipment Damage
Hazard.
Dan shock individuals
or short
equipment circuitry.
Disconnect power supply before
installation.
Location
install the thermostat about 5 ft (1.5m) above the
floor in an area with good air circulation at average
temperature.
Do not install the thermostat where it
can be affected by:
-- drafts or dead spots behind doors and in
corners.
-- hot or cold air from ducts.
-- radiant heat from the sun or appliances.
-- concealed pipes and chimneys.
-- unheated (uncooled) areas such as an outside
wall behind the thermostat.
MountingWallplate to Wall
Mount the T8775A,C wallplate, with the screws
provided. See Fig. 1.
WALL
ANCHORS
(2) --
WALL
PLATE
_
I
I INCI/SCREW
(2)
M_
,>
z_WHEN
USING WALL ANCHORS,
DRILL 3,¸¸16 IN HOLES
FOR DRYWALL¸
7/32 IN HOLES FOR PLASTER¸
Fig. 1. Mounting watlplate
to wall.
© U.S
Registered
Trademark
° Patents Pending
© 2004 Honeywell
International inc.
All Rights Reserved
_
69-1677ES--1

Advertisement

loading

Summary of Contents for Honeywell Round T8775A

  • Page 1 -- radiant heat from the sun or appliances. -- concealed pipes and chimneys. -- unheated (uncooled) areas such as an outside wall behind the thermostat. MountingWallplate to Wall Mount the T8775A,C wallplate, with the screws provided. See Fig. 1. WALL WALL PLATE...
  • Page 2 Refer to Fig. 2 through 6 for typical wiring hookups. AND OVERLOAD PROTEC[ ON AS REQU RED Fig. 2. Typical hookup of T8775A in a heat-only APOWEf_SUP>LY Pf_OVDE Fig, 3. Typical hookup of T8775C in heat-only with fan.
  • Page 3 T8775A, CUSTOMIZE THERMOSTAT Setting Fuel Switch (T8775C only) The fuel switch is preset at the factory position See Fig. 7. This is the correct or oil systems• tf the T8775C is being installed electric heat system, or a heat pump, set the switch to...
  • Page 4 T8775A, C THE DIGITAL ROUND SYSTEM (18_5C ONLYi S_LECIS INDICATORS THERMOSTAT HAS CALLED F_R HEATING ORCOOt J NG_ THATSHOW DIGITAL DISPLAY_ b_SPLAY8ROOM ORSE] ]EM_'ERAI U_E BACKI-IGHT BUTTON Fig. SYSTEMSwitch Heat: The thermostat controls system. Off: Both heating and cooling Cool:...

This manual is also suitable for:

Digital round t8775c