The AR-DU3 is equipped with the duplex feature only, and the AR-DU4 is additionally equipped with the manual paper feed feature. AR-DU3 models is equipped with the paper exit port, which allows installation of the optional paper exit tray, the AR-TE3. (AR-DU4 standard)
Approx. 7.5kg printed paper. Paper capacity 100 sheets AR-DU4: When the tray is extended fully. (standard paper:80g/m²) AR-DU3: The AR-TE3 is not installed. Post card: 20 sheets B.Duplex part Transparency film: 20 sheets Paper type Plain, recycled, pre-printed, pre-punched, Method...
•Carry out the installation after checking that the DATA indicator on the operation panel is neither lit nor blinking. •For installing AR-DU3, an optional desk (multi purpose drawer, stand/3 x 500 sheet paper drawer or stand/MPD & 2000 sheet drawer) must have been installed.
Page 5
6) Adjust the position of the paper guides of the bypass tray. Refer to "Adjustments" described later. Positioning boss 7) Carry out the off center adjustment. Positioning boss Duplex module AR-DU3/DU4/TE3 UNPACKING AND INSTALLATION 4-2...
ADU transport sensor 1 (APPD1) Manual take-up roller ADU paper exit sensor (APOD) ADU transport sensor 2 (APPD2) Manual feed paper sensor (MPED) ADU paper exit gate ADU transport roller 3 ADU transport roller 2 AR-DU3/DU4/TE3 EXTERNAL VIEWS AND INTERNAL STRUCTURES 5-1...
Page 7
Paper feed clutch from the manual paper feed tray AR-DU4 only MPFS Manual paper feed solenoid Paper feed solenoid from the manual paper feed tray AR-DU4 only Shutter solenoid Shutter open/close in manual paper feed AR-DU4 only AR-DU3/DU4/TE3 EXTERNAL VIEWS AND INTERNAL STRUCTURES 5-2...
Open the "Paper" tab shown in the illustration below and select "Left Side Tray" in the "Output" drop down. Note: The settings screens above will appear only if the devices have been set properly in the printer driver configuration AR-DU3/DU4/TE3 MACHINE OPERATION 6-1...
7) Turn off the main switch to cancel the setting mode. 6) "MINIMUM SIZE" is displayed. Move the manual paper feed guide F to the minimum position, and press [OK] key. 7) Turn off the main switch to cancel the setting mode. AR-DU3/DU4/TE3 ADJUSTMENTS 7-1...
5) Under the state 1), press [3] key and then [START] key, and the menu below will be displayed. Enter the value of "MIN" specified on the label with [0] - [9] keys. After entering the value of "MIN," press CUSTOM SETTINGS key, and menu (1) will be displayed. AR-DU3/DU4/TE3 ADJUSTMENTS 7-2...
*1: Replacement reference: Use the counter value of each paper feed port. Paper feed roller/Separation pad: 80K or 2 years 2. Maintenance A. Unit installing side (Back) B. Inside of the paper exit section/ADU side door AR-DU3/DU4/TE3 DISASSEMBLY AND ASSEMBLY, MAINTENANCE 8-1...
3. Disassembly and assembly cover A. External cabinet For disassembly of the paper feed unit and the lower cover, refer to (1) ADU lower cover (AR-DU3 only) the following descriptions. 1) Open the ADU cover. 2) Remove the ADU lower cover.
Page 13
(4) Paper exit section cover/door switch B. Manual paper feed section (AR-DU4 only) (1) Manual paper feed unit (5) Upper cabinet/paper exit sensor AR-DU3/DU4/TE3 DISASSEMBLY AND ASSEMBLY, MAINTENANCE 8-3...
Page 14
3) Fix the mounting plate with a screw. When the rotational volume sensor is replaced, the sensor value must be adjusted to the paper size (mark on the tray). (Refer to the previous procedure of "Adjustment.") AR-DU3/DU4/TE3 DISASSEMBLY AND ASSEMBLY, MAINTENANCE 8-4...
Page 15
E. ADU gate solenoid Note: When assembling, fit the edge of the solenoid mounting plate with the center of the mark. F. Rollers/Belts/Clutches C. Upper transport motor/Lower transport motor/Fan (1) Transport follower roller motor AR-DU3/DU4/TE3 DISASSEMBLY AND ASSEMBLY, MAINTENANCE 8-5...
Page 16
(2) Transport roller/belt/clutch/gear G. Sensors (1) Paper entry sensor (2) Transport sensor (3) ADU paper entry roller/belt/clutch/gear AR-DU3/DU4/TE3 DISASSEMBLY AND ASSEMBLY, MAINTENANCE 8-6...
Page 25
COPYRIGHT COPYRIGHT COPYRIGHT 2001 BY SHARP CORPORATION 2001 BY SHARP CORPORATION 2001 BY SHARP CORPORATION All rights reserved. All rights reserved. All rights reserved. Printed in Japan. Printed in Japan. Printed in Japan. No part of this publication may be reproduced,...