Page 1
[ 9 ] CIRCUIT DIAGRAM ........9-1 Parts marked with “ ” is important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set. SHARP CORPORATION CODE: 00ZARPB8//A1E DIGITAL COPIER...
Paper size Tray 1 AB series The number of trays supported depends on each model. PS2 expansion kit (AR-PS1) Printer expansion kit (AR-PB8) Expansion memory (Commercially available 168 pin EDO DIMM: 16MB/32MB/64MB) Item Paper size Paper exit Shifter Page description...
Microsoft Windows 98 Printer driver Microsoft Windows NT4.0 Macintosh OS (System 7.5 or later) Network control Sharp Admin Software software Outline Western language 31 fonts (PCL6 Built-in fonts compatible) Outline European language 45 fonts (PCL6 compatible) for Windows Screen font...
AR-PA1 Lamp 2 (DATA, ONLINE) Display 20 digits 2 lines When installing the AR-PB8 to a model which is not equipped with the LCD panel, the LCD kit (AR-PA1) must be installed to. a. LCD message Status LCD display AUTO...
AR-PB8 (2) Network board 10/100 Base TX TCP/IP, IPX/SPX, Ether Talk, Jet Admin A 10 Base 2/T TCP/IP, IPX/SPX, Ether Talk, Jet Admin A (3) PS kit A Model name AR-PS1 Page description PostScript level 2 emulation language Built-in fonts...
3. Since printing order differs in simplex printing and duplex printing, the insert surface differs in simplex and duplex in the case where there is a difference between the front and the back, for example, the letter head. 1 – 5 AR-PB8 Duplex...
AR-PB8 [3] SET UP 1. Procedures on the copier (operation panel) When installing the LCD panel kit simultaneonsly. A. Copier operation panel disassembly • Remove screws and connector, and remove the operation panel. B. Cover disassembly • Remove screw and disengage pawls, and remove the cover.
E. Mother board installation (Packed together with the LCD kit.) • Insert the connectors and fix them, then connect the connec- tors of the copier to them. F. Shield plate installation • Fix the shield plate with screws. 3 – 2 AR-PB8...
AR-PB8 G. PWB cover installation • Install the PWB cover with screws. 3. Expansion memory installation • Fix the memory PWB with pawls. 4. PS kit (AR-PS1) installation • Fix the PS PWB with pawl. Note: The DIMM connector and the PS-PWB are provided with the reverse insertion protection key(notch).
<4> Proceed to step 5). 2) Search for the printer driver by clicking [Other Locations...] button. 3) Insert the SHARP Software CD-ROM into the CD-ROM drive, type R:\English\WinXX and click the [OK] button. 4) After Windows finds the printer driver, click the [Finish] button to continue the installation.
2) Display a list of all the printer drivers by checking “Display a list of all the drivers in a specific location, ...” and clicking the [Next] button. 3) Click the [Have Disk...] button. 4) Insert the SHARP Software CD-ROM into the CD-ROM drive, type R:\English\WinXX, and click the [OK] button. appears, type 5) Choose the appropriate printer driver from those listed below and click the [Next] button.
The following steps use the example of a local printer. 6) Click the [Have Disk...] button. 7) Insert the SHARP Software CD-ROM into the CD-ROM drive, type R:\English\WinXX, and click the [OK] button. 8) Choose the appropriate printer driver from those listed below and click the [Next] button.
5) Check the checkbox for the port you are using and click the [Next] button. 6) Click the [Have Disk...] button. 7) Insert the SHARP Software CD-ROM into the CD-ROM drive, type R:\English\WinNT and click the [OK] button. 8) Choose the appropriate printer driver from those listed below and click the [Next] button.
ON LINE MENU ITEM 2) Press the MENU key repeatedly until the required menu appears. ENTER 3) Press the ITEM key repeatedly until the required item appears. 4 – 1 AR-PB8 DATA ON LINE MENU ITEM DATA ON LINE MENU...
AR-PB8 4) Press the Left or Right arrow key to change the setting. • The current value is marked with an asterisk ( ). DATA LINE MENU ITEM ENTER 5) After choosing the required value, press the ENTER key. •...
The machine enters the version up mode of the printer PWB flash ROM. For details, refer to the printer PWB flash ROM version up procedure described later. 456 (0.75 sec) Blank (1.0 sec) Blank (1.0 sec) Repetition 5 – 1 AR-PB8 Initial Set range value repetition...
AR-PB8 [6] CONFIGURATION REPORT AND TEST PAGE To test print the configuration page and font list, use the following procedure: 1) Press the ON LINE key to switch the printer to the offline mode. DATA ON LINE MENU ITEM 2) Press the MENU key to display the Test Menu.
AR-PB8 [7] FIRMWARE VERSION UP 1. Cases where flash memory rewriting is required In the following cases, the program in the printer control PWB flash memory must be rewritten. 1) When a bug or other error is found 2) Data stored in the flash memory is destroyed or deleted.
Printer PWB ROM defect, data failure Check and Check the connectors and harness of remedy the Printer PWB and the MCU PWB. Check grounding of the machine. Check the ROM of the Printer PWB. 8 – 1 AR-PB8 Detail of trouble...