Table of Contents
Advertisement
Parts and their functions
$ Control panel
OPERATE
ON
OFF
INCOM
LEVEL
IRIS
AUTO
MANU
LOCK
P START POINT button
Press this to set the position at which the tracing memory
is to be started.
Q START/STOP button
Press this to start or stop entry into the tracing memory.
R RESTORE button
Press this to correct or change what has been entered in
the tracing memory.
S RESET button
Press this to erase what has been entered in the tracing
memory.
T TR/PSET button
This is used to select the tracing memory mode or preset
memory mode.
Each time it is pressed, the tracing memory mode or
preset memory mode is selected in turn.
When the tracing memory mode is selected, the button's
lamp comes on; when the preset memory mode is
selected, the lamp goes off.
U M.LOCK button
This is used to disable or enable the recording of settings
in the tracing memory or preset memory.
Each time it is pressed, recording disable or enable is
selected in turn.
When recording is disabled, the button's lamp comes on;
when it is enabled, the lamp goes off.
V
T U
IRIS
ZOOM
FOCUS
OPEN
TELE
FAR
WHITE
AWC
BAL
GAIN
AUTO
A
MANU
MODE
BAR
NG
B
CAM
OK
ABC
DATA SET
ATW
CALL
TR/PSET M.LOCK
1
2
3
CLOSE
WIDE
NEAR
TR
PSET
TELE
MEMORY
11
12
13
EMPTY
21
22
23
IRIS
FOCUS
31
32
33
41
42
43
CLOSE
OPEN
NEAR
WIDE
FAR
ZOOM/FOCUS/IRIS
LIMIT
ON
W
P
CAMERA CONTROL
LAMP
DEF
LCD
CONTRAST
START
R/B
POINT
CAMERA
GAIN/PED
MENU
OK
CONTROL
TRACING/PRESET MEMORY
4
5
6
7
8
9
10
PRIORITY
14
15
16
17
18
19
20
SPEED
LOW
FULL
HIGH
24
25
26
27
28
29
130
IRIS
FOCUS
L
34
35
36
37
38
39
40
44
45
46
47
48
49
50
CLOSE
NEAR
LIMIT
OFF
V MEMORY button
This is pressed when the pan-tilt head system's settings
are to be entered as a preset memory into one of the
TRACING/PRESET MEMORY buttons [1] through [50].
Up to 50 settings can be entered per pan-tilt head system
into a preset memory.
Pan-tilt head system's settings
Pan-tilt head:
Pan-tilt position
Camera:
Zoom, focus, iris, white balance
How to enter settings into the preset memory
1 Select the pan-tilt head system using the
CONTROL/PREVIEW MONITOR OUT SEL button.
2 Select the preset memory mode using the
TP/PSET button.
3 Set the pan-tilt head system.
4 While pressing the MEMORY button, press one of
the TRACING/PRESET MEMORY buttons from [1]
through [50] into which the settings are to be
entered.
W TRACING/PRESET MEMORY buttons [1] to [50]
Tracing memory or preset memory data is entered into
these buttons.
Tracing memory: [1] through [10]
Preset memory : [1] through [50]
<Note>
It is not possible to enter preset memory data into any
button in which a tracing memory has already been
entered.
8
Q
R
S
PAN/TILT SET
WIP
H/F
EXT
ND
OPTION
TRACING MEMORY
START/STOP
RESTORE
RESET
TALLY
1
2
3
4
5
AUX
CONTROL/PREVIEW MONITOR OUT SEL
UP
R
OPEN
DOWN
FAR
PAN/TILT/FOCUS/IRIS
Advertisement
Table of Contents
