Contents What is ZSim? ................1 System Requirements ..............1 ZSim v5.XX vs. v4.XX ..............1 Loading ZSim to Your Printer ............1 Configuring ZSim – PF, PM and PX Printers .........2 Navigating the ZSim Configuration Menu ......2 Configuring ZSim – PD41 ............3 Configuring ZSim for the First Time ..........4 Configuring ZSim through text downloads ......4 Using the Configuration Menu ........7 Initial Setup Configuration Menu .....8...
Page 4
Peel Off Length ..........16 Permanent Save ..........16 Print Configuration Label .......17 Print Mode ............17 Redo Config ............17 Reset Tuning ...........17 Save Current ...........17 Select Character Set .........17 Simulation Resolution ........18 Units ...............18 Use Last Saved ..........18 X-Offset ............18 Y-Offset ............18 Troubleshooting ZSim ..............19 Entering Passwords ..............20 Modes................20...
Page 5
Intermec Fingerprint programming language but has been list protected. The Software may include programs written by Intermec as well as programs written by others which have been incorporated into the Software by Intermec. The Software includes any disks or media on which it is recorded, any printed Documentation or any “on-line”...
Page 6
You agree that if any unauthorized copies are made, or if the Software is used in violation of this License, Intermec shall have the right to obtain an injunction against the unauthorized copying or use, in addition to any other rights and remedies Intermec might have.
What is ZSim? ZSim is a Zebra™ interpreter program that allows you to use your legacy Zebra programs on an Intermec EasyCoder PF2i, PF4i, PF4i Compact Industrial, PM4i, PX4i, PX6i or PD41 printer with Fingerprint. All you need to do is download the ZSim program onto your printer, configure a few settings, and start sending Zebra commands.
Memory card slot ZSim CompactFlash card Make sure you insert the card properly by looking at the arrows on the card. Do not use force to insert the card. 4 Turn off the printer and remove the ZSim card when the screen prompts you.
An Entry point is for input purpose, where you may enter some parameter value or turn on/off a function. It is defined by lead text on the first display row (without ending slash) and a cursor or the value “on/off” on the second display row. Description Setup Open and close the ZSim or Fingerprint menu...
Configuring ZSim for the First Time After you power on your printer, the ZSim menu takes you to the Initial Setup Configuration menu. Note: For the EasyCoder PD41, the configuration is generated automatically since no menu is available. More information can be found in the next section.
ensure a secure update. Verify that the update has been carried out by printing a configuration label. Note: The default instruction prefix “^” and the default delimiter “,” are used in the samples at the end of the section. [ParamName] ParamNo ParamValue Default Comment...
Page 12
[ParamName] ParamNo ParamValue Default Comment Control Any ASCII char. Instruction Prefix Command Any ASCII char. Delimiter Units inch/mm 0=inch, 1=mm Optimize Batch -1/0 ON/OFF Y-offset in percent Skid comp.+/-0.1- Character Set Single byte char. set Media Type 0/1/2 0=GAPS, 1=STRIP, 2=MARK Paper Type auto...
Using the Configuration Menu You need to update configuration commands when you perform functions such as changing media. You can access the Configuration menu at any time by pressing Setup. For help locating the command you want to change, see the Configuration Command Menu. See the section ”Understanding the Configuration Commands”...
Configuration Command Menu, Part 1 Calibrate Print Mode Tear Off Peel Off Rewind Cutter Units inches Media Media Contrast Media Contrast Media Type Continuous Non Cont. Mark Non Cont. Web Paper Type Thermal Transfer Direct Thermal Media Size Label Length Label Length (mm/inches) XXXX Label Width...
Configuration Command Menu, Part 3 Input Port Network COMParams Parallel Serial IPParams Select Character Set Select Character Set XXXX ZSim v5.XX User‘s Guide...
Understanding the Configuration Commands Use the following configuration command descriptions to understand the parameters you are setting with the ZSim program. Allow Reverse Purpose: Allows reverse printing on the label, both for the entire label (^LR) and for specific fields (^FR). Default: Calibrate Measures the label length and calibrates the sensors.
length of media will be fed out before printing starts. A negative start adjustment means that the specified length of media will be pulled back before printing starts. Default: Printer Model: PF2/4i PM4i PX4/6i PD41 Start Adjust (dots): -100 -100 -133 Default Stop Adjust Determines how much media in [dots] feeds through...
Label Length Purpose: Specifies the length of the labels in [inches] or [mm] depending on the units selected. This parameter is automatically set during the Initial Setup Configuration process. Note: You can only set the label length if the Media Type is set to Continuous.
Fixed length strip Optimize Bar Code Magnification Purpose: It is highly recommended to use an Intermec printer with the same printhead resolution as the replaced Zebra printer. In case of replacing a 152 dpi Zebra printer, use an Intermec printer with 300 dpi printhead.
Default: Optimize Image Magnification Purpose: It is highly recommended to use an Intermec printer with the same printhead resolution as the replaced Zebra printer. In case of replacing a 152 dpi Zebra printer, use an Intermec printer with 300 dpi printhead.
formats, but they will not be loaded when the printer starts up. Default: Print Configuration Label Purpose: Prints the current ZSim configuration settings on a label. Print Mode Purpose: Determines the printer operating mode and sets the label origin to suit the corresponding mode: •...
^CI command again. Simulation Resolution Purpose: Set the resolution of the Zebra printer being simulated. You can set this command to 152 dpi, 203 dpi, or 300 dpi. Note: The resolution between the simulated printer and your printer may cause a difference in bar code quality.
Troubleshooting ZSim If you have problems using the ZSim program on your printer, look for your symptom in the next table and then try the suggested solutions. Symptoms and Solutions Symptom Solution Label is partially printed, or the You need to calibrate the ZSim program every time you load new media.
Entering Passwords When entering IP parameters from the Simulators menu, the user may be requested for a password for the administrator. This will happen only if the password has been changed to other value than the default value. In this case the display will show the following prompt: Admin Password: Since there are no alpha keys on the printer’s keyboard, you will need to encode alpha and special characters using the numeric part of the...
Selecting Characters Each key on the printer’s keyboard gives access to one, two, or three characters. Alternative characters are selected by hitting a key repeatedly, similar to a cellular phone. For example, hit <1> once to select 1, hit <1> twice to select C, hit <1> three times to select D, hit <1>...