Spektrum DX3C Instruction Manual
3-channel 2.4ghz dsm radio system
Hide thumbs
Also See for DX3C:
- Bedienungsanleitung (18 pages) ,
- Manuel d'utilisation (18 pages) ,
- Instruction manual (18 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Spektrum DX3C
Summary of Contents for Spektrum DX3C
- Page 1 Инструкция для Spektrum DX3C Перейти в карточку товара 8 800 775 98 98...
- Page 2 3-Channel 2.4GHz DSM Radio System Instruction Manual Bedienungsanleitung Manuel d’utilisation Manuale di istruzioni...
- Page 3 If you are a newcomer to radio controlled models, please seek help from an experienced modeler or your local hobby shop. FRANCE RF SETTING: The DX3C has a France RF setting that complies with French regulations. Always use the France power set- ting when operating the transmitter outdoors in France.
-
Page 4: Table Of Contents
Thank you for purchasing the Spektrum DX3C transmitter. With advanced programming, refined ergonomics, a sleek style and an SD card slot for enhancements, the DX3C is perfect for sport drivers. TABLE OF CONTENTS System Features ............3 Travel ..............8 Table of Contents ............3 Bind Transmitter to Receiver ......9... -
Page 5: Identifying Controls And Switches
Roller Selector Antenna Memory Card Port Press power switch power ON the transmitter. come on, a Spektrum logo screen will show, then the Main Screen will show on INSTALLING BATTERIES 1. Push in door a small amount to release the retaining tab , then remove door. -
Page 6: Rubber Grip
Remove the grip by lifting the edge of the grip and pulling the grip away from the handle. Install a grip by aligning grip tabs with handle slots and pressing the grip in place. SD Memory Card an SD card. To upload new software to your DX3C transmitter: 1. Remove the grip from the back of the transmitter handle. card reader port. -
Page 7: Modelmatch
ModelMatch The DX3C features ModelMatch technology that prevents operating a model using the wrong model memory. During the binding process, the receiver stores code that is assigned to the specific model that is currently selected in the transmitter. For example: if the model that is selected in the transmitter is model #3, when a receiver is bound to that transmitter, the receiver will only operate is again selected in the transmitter, the receiver bound to model #3 will connect. -
Page 8: Programming Guide
PROGRAMMING GUIDE Roller and LCD Screen Use Some racers find it convenient to use a thumb to make This transmitter features one-touch programming using a one-handed programming, controlling the model with one hand Rolling Selector. The Rolling Selector has three functions: while making programming adjustments with the other. -
Page 9: Select
Select Select function opens a model memory for control of a model Model model memory, all settings will be at factory default. CAUTION: Do NOT change the model in Model Select Model 1: while operating a model. Change of the model interrupts NAME-01 transmitter signal to a receiver and may cause a crash. -
Page 10: Bind Transmitter To Receiver
Expo Expo steering, throttle and/or brake. A positive Steering Expo value, for example, decreases steering sensitivity around neutral making it Steering easier to drive at high speeds in a straight line while still allow- ing for maximum turning radius. While sensitivity with positive Expo is decreased around neutral, it increases the sensitivity near the end of travel. -
Page 11: Sub-Trim
Sub-Trim The Sub-Trim function allows electronic adjustment or centering Sub-Trim of each servo to get the servo arm exactly perpendicular to the servo, or in the exact optimum desired position. Minor sub-trim values can be used to correct this offset inaccuracy. Sub-trim is Steering adjustable for each of the 3 channels. -
Page 12: Switch
Switch to these special functions: ST trim Assigns a switch to adjust center or neutral so steering tracks straight TH trim Assigns the throttle idle adjustment to switch. Ad- or rolling idle for some models. Decreasing idle can enable a drag brake. Increasing idle can keep a model rolling until the brake is used. -
Page 13: Copy
A Username RS Port:Bind name shows on the Main Screen. User name defaults to Alert:4.1V Spektrum. In the System screen highlight the User Name and press the Contrast:20 roller to access the function. Use the roller to select the position, Buzzer: Off then press the roller to access a character. -
Page 14: Reset
Reset Reset The Model Reset function restores factory default settings for the active model memory. A Choosing Yes affirms erasing saved settings for the active model memory and return of factory defaults. B A box shows around selected text. C Choosing No returns to the List Screen. CAUTION: Model information saved in a memory is erased when that model memory is copied over or reset to factory default settings. -
Page 15: Steer Mix
Steer Mix Steer Mix function supports mixing Steering to Auxiliary channel Steer Mix so the Auxiliary input follows input to Steering. Steer mix is usually used to manage how much rear steering Type: Inh follows front steering inputs. mix rates so crab steering and four-wheel steering can be used momentarily with a switch. -
Page 16: Troubleshooting Guide
FCC INFORMATION Antenna Separation Distance When operating your Spektrum transmitter, please be sure to any interference received, including interference that may cause undesired operation. antenna to meet RF exposure safety requirements as determined CAUTION: Changes or modifications not expressly by FCC regulations. -
Page 17: Warranty And Repair Policy
WARRANTY AND REPAIR POLICY Warranty Period Warranty Services Questions, Assistance, and Repairs Your local hobby store and/or place of purchase cannot provide defects in materials and workmanship for a period of 1 year warranty support or repair. Once assembly, setup or use of the from the date of purchase by the Purchaser. -
Page 18: Warranty And Service Contact Information
Spektrum DX3C Описание Характеристики...