1. Manuals
  2. Brands
  3. SkyLink Manuals
  4. Emergency Phone
  5. ED-100
  6. User manual

SkyLink DIAL-ALERT ED-100 User Manual

Emergency dialer
Hide thumbs Also See for DIAL-ALERT ED-100:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Manual
www.skylinkhome.com
Emergency Dialer
TM
DIAL-ALERT
MODEL: ED-100
CUSTOMER SERVICE
17 Sheard Avenue, Brampton,
Ontario, Canada L6Y 1J3
Tel : (905) 456-8883
PAT. D410633
Fax : (905) 456-7819
6243000B1
101A083-002
FEB, 2006.
Email : support@skylinkhome.com
©2006 SKYLINK GROUP

Advertisement

Table of Contents
loading

Related Manuals for SkyLink DIAL-ALERT ED-100

Summary of Contents for SkyLink DIAL-ALERT ED-100

  • Page 1 Emergency Dialer DIAL-ALERT MODEL: ED-100 CUSTOMER SERVICE 17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3 Tel : (905) 456-8883 PAT. D410633 Fax : (905) 456-7819 6243000B1 101A083-002 FEB, 2006. Email : support@skylinkhome.com ©2006 SKYLINK GROUP...
  • Page 2 SKYLINK TECHNOLOGIES INC. Your Guide to the Emergency Dialer DIAL-ALERT MODEL: ED-100 – –...

  • Page 3: Table Of Contents

    PANIC TRANSMITTER BATTERY TABLE OF CONTENTS The Panic Transmitter operates on three 3-volt lithium batteries (CR-1220) PACKAGE CONTENTS....................4 that are installed at the factory. The battery storage life of these lithium OVERVIEW......................5 batteries is approximately five years. There are two screws on the back of INSTALLATION........................6 the transmitter that hold the top and bottom case together.

  • Page 4: Package Contents

    PACKAGE CONTENTS BATTERY MAINTENANCE The ED-100 Dial-Alert comes with 4 batteries that at some point you may All materials required for installation are included with this package have to replace: 1 Dial-Alert (AD-433) 9 volt alkaline battery for the Dial-Alert...

  • Page 5: Overview

    (after the dialer is activated), the display will show “no LInE” and the backlit keypad will flash. To return to standby mode (Display shows the time), 2. The button is pressed on the panic transmitter (included in the ED-100 package) press and hold the panic button [O] for 2 seconds.

  • Page 6: Installation

    INSTALLATION ADVANCED PROGRAMMING DELAY DIALING The Dial-Alert is installed using the screws provided. We have also included double sided tape, to use for temporary installation while you are positioning The delay dialing allows the dialer to dial the preset phone numbers after a the dialer.
  • Page 7 ADVANCED PROGRAMMING INSTALLATION DELETE PROGRAMMED PANIC TRANSMITTER: 2. Thread the telephone line through the top hole in the back of the unit and plug it into Once a panic transmitter is learned, it is stored in memory. In order to delete the "LINE"...
  • Page 8 The default setting for the speaker is "On". dial the preset telephone numbers and play the pre-recorded message. To program Skylink’s panic transmitter: 1. Press the [L] key, display will show “L”. 2. Press the [5] key, display will show “ L 5 Id codE ”.

  • Page 9: Lights And Sounds

    ADVANCED PROGRAMMING LIGHTS AND SOUNDS PROGRAM THE CALLING TIME Below is an explaination of the lights and sounds of the Dial-Alert. The calling time is the amount of time the phone will ring until the call is dis- LIGHTS connected. If the phone is not picked up within this period of time, the dialer will either call again, (depends on the redial count), or advance to the next phone ACPWR light on dialer is being powered by AC adapter.

  • Page 10: Standard Programming

    PANIC TRANSMITTER STANDARD PROGRAMMING The Panic Transmitter conveniently fits on any keychain or necklace. It When you plug in the dialer for the first time, you will hear a double beep and allows you to activate the Dial-Alert from a distance of approximately 100 feet all the lights will be on for 2 seconds, the keypad will continue to flash and from the dialer.

  • Page 11: Playback Pre-Recorded Message

    STANDARD PROGRAMMING STANDARD PROGRAMMING TO REVIEW OR MODIFY THE PRE-PROGRAMMED PHONE NUM- PLAYBACK PRE-RECORDED MESSAGE BERS, THE REDIAL COUNT AND/OR THE REPEAT TIMES OF A Press and release the [R/P] key, display will show “PLAY” and the dialer will PHONE NUMBER. beep.

  • Page 12: Storing Telephone Numbers In Memory (Sends Both Emergency Voice Message And Numeric Information)

    STANDARD PROGRAMMING STANDARD PROGRAMMING C. Storing telephone numbers in memory (Sends the numeric 7. The dialer is now in standby mode. (Display shows the time). information to pager only) The sequence to store a telephone number is as follows: 1. Press the [MEM] key, the display will show a letter “M” on the upper left [MEM] , enter memory location (1-9) , enter telephone # , [MEM] , enter corner.

Table of Contents