Advertisement
SPECIFICATIONS
RMS Continuous Power (at 14AV , 20 - 200 Hz)
• Per channel into 4 ohms
(~1
% THD+N)
600W x 1
• Per channel into 2 ohms
(~1
% THD+N)
600W x 1
SIN Ratio (IHF A Weighted, Reference: rated power into 4 ohms)
11 OdBA
CEA2006 SIN Ratio (IHF A Weighted, Reference: 1W into 4 ohms)
80dBA
Input Impedance
10k ohms
Frequency Response
20Hz (±1dB) - 200Hz(-3dB)
Crossover Frequency (Variable)
50 - 200Hz (-24dB I oct.)
Input Sensitivity (V
I
at 10k ohms)
0.1 - 8.0V
Dimensions
• Width
257mm (10-1/8")
• Height
62mm
(2-7/16")
• Depth
192mm
(7-9/16")
Weight
3.11 kg
NOTE:
For product improvement, specifications and design are subject to change without notice.
ACCESSORIES
• Self-Tapping Screw (M4 x 40, see
CD
of Fig.2 on the left)
4
• Machine Screw (M2.6 x 14, see
®
of Fig.3 on the left)
8
• Machine Screw (M4 x 36, see
@
of FigA on the left)
4
• Joint Cap (see @ of Fig.3/4 on the left)
4
• Speaker Plug
1
• Hexagonal Wrench
1 SET
INSTALLATION (Fig. 1 - Fig. 4)
With this series of amplifiers, up to three units can be stacked together in a typical installation.
Depending on the number of units you wish to install, refer to instructions A to C below.
&
CAUTION
• Caution on connection terminals/parts
• Do not allow other objects (particularly electrically conductive) to get too close or in contact with
any of the unit's terminalslparts (power supply, fuse, speaker output terminal, RCA connector,
etc.). Doing so may result in short circuit or accident.
Note:
When stacking amplifiers, do not install horizontally or at an incline. Any installation other than
parallel to the vehicle floor, invalidates the warranty.
Preparation for installation
1. Using the amplifier as a template, mark the four screw locations.
2. Make sure there are no objects behind the surface that may become damaged during drilling.
3. Drill the screw holes.
4. Position the PDX-1.600M over the screw holes, and secure with four self-tapping screws.
NOTE:
To securely connect the ground lead, use an already installed screw on the metal part of the vehicle
(marked *). Be sure this is a good ground by checking continuity to the battery (-) terminal. As
much as possible connect all equipment to the same ground point. These procedures will help
eliminate noise.
A. Single unit installation
1. Position the unit over the screw holes you prepared earlier.
2. Remove the four corner top caps on top using the hexagon wrench (large, supplied). Refer to fig.1.
3. Fasten the unit down with the four self-tapping screws (M4 x 40, supplied).Refer to fig.2.
NOTE:
A magnetic screwdriver is recommended to prevent the screw being dropped while tightening.
4. Re-attach the four top caps and hand-tighten.
B. Stack installation of two units
1. Firstly, securely install one unit, as described in steps 1-3 of A above.
2. Attach the four joint caps in the four corners of the first unit with 2 machine screws
(M2.6 x 14, supplied) per each cap. Refer to fig.3.
3. Stack the second unit on top of the installed unit, aligning the second unit's feet with the joint
caps of the first unit.
4. Remove the four corner top caps of the second unit using the hexagon wrench (large, supplied).
5. Insert the four machine screws (M4 x 36, supplied) through the top of the second unit into the
four joint caps of the lower unit to connect them together. Refer to figA
6. Re-attach the four top caps and hand-tighten.
C. Stack installation of three units
1. Firstly, securely install the first two units firmly as described in steps 1 to 5 of B above.
2. Next, install the third unit as described for the second unit in B above. With this, stack installation
of the 3 units is completed.
Advertisement
