– Power supply units – Pumps – Blowers and fans – Motor generators – Similar units to listed above This practice ensures correct grounding of the units. • If an electrical accident occurs: ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
– Use caution; do not become a victim yourself. – Switch off power. – Send another person to get medical aid. Safety inspection guide The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each machine was designed and built, required safety items were installed to protect users and service technicians from injury.
The safety notices in this section are provided in the following languages: • English • Arabic • Brazilian Portuguese • French • German • Hebrew • Japanese • Korean • Spanish • Traditional Chinese DANGER ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 13
Before the computer is powered on after FRU replacement, make sure all screws, springs, and other small parts are in place and are not left loose inside the computer. Verify this by shaking the computer and listening for rattling sounds. Metallic parts or metal flakes can cause electrical shorts. DANGER Some standby batteries contain a small amount of nickel and cadmium.
Page 14
Unless hot swap is allowed for the FRU being replaced, do as follows before removing it: power off the computer, unplug all power cords from electrical outlets, remove the battery pack, and disconnect any interconnecting cables. ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 16
Use somente a bateria nas partes listadas apropriadas ao substituir o pacote da bateria. O uso de uma bateria incorreta pode resultar em combustão ou explosão da bateria. PERIGO ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 17
A bateria de lítio pode causar incêndio, explosão ou graves queimaduras. Não a recarregue, remova seu conector polarizado, desmonte-a, aqueça-a acima de 100°C (212°F), incinere-a, ou exponha o conteúdo de sua célula à água. Descarte a bateria conforme requerido pelas leis ou regulamentos locais. Use somente a bateria nas partes listadas apropriadas.
Page 18
Consultez un médecin si des symptômes persistent après le lavage. DANGER Afin d'éviter tout risque de choc électrique, ne retirez pas le cache en plastique protégeant la partie inférieure de la carte d'alimentation. ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 19
DANGER Bien que le voltage des batteries principales soit peu élevé, le court-circuit ou la mise à la masse d'une batterie peut produire suffisamment de courant pour brûler des matériaux combustibles ou causer des brûlures corporelles graves. DANGER Si le remplacement à chaud n'est pas autorisé pour l'unité remplaçable sur site que vous remplacez, procédez comme suit avant de retirer l'unité...
Page 20
Wenn ein Austausch der FRU bei laufendem Betrieb nicht erlaubt ist, gehen Sie beim Austausch der FRU wie folgt vor: Schalten Sie den Computer aus, ziehen Sie alle Netzkabel von den Netzsteckdosen ab, entfernen Sie den Akku und ziehen Sie alle miteinander verbundenen Kabel ab. ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 25
Antes de encender el sistema despues de sustituir una FRU, compruebe que todos los tornillos, muelles y demás piezas pequeñas se encuentran en su sitio y no se encuentran sueltas dentro del sistema. Compruébelo agitando el sistema y escuchando los posibles ruidos que provocarían. Las piezas metálicas pueden causar cortocircuitos eléctricos.
Page 26
Salvo que se permita el intercambio en caliente para la unidad sustituible localmente, realice lo siguiente antes de extraerla: apague el sistema, desconecte todos los cables de alimentación de las tomas de alimentación eléctrica, extraiga la batería y desconecte los cables de interconexión. ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
System Disassembly/Reassembly videos that show the FRU removals or replacements for the Lenovo® authorized service technicians are available in the following support site: http://www.lenovoservicetraining.com. Advise customers to contact the Customer Support Center at 800-426-7378 if they need assistance in obtaining or installing any software fixes, drivers, and BIOS downloads.
Dynamic Configure To Order (CTO) This provides the ability for a customer to configure an IBM® or a Lenovo solution from an eSite, and have this configuration sent to fulfillment, where it is built and shipped directly to the customer. The machine label, Product Entitlement Warehouse (PEW), eSupport, and the HMM will load these products as the 4-digit MT and 3-digit model, where model =“CTO”...
• eSupport can be used to view the list of key commodities built in a particular machine serial (this is the same record found in PEW). • eSupport can be accessed at the following Web site: http://www.lenovo.com/support. • To view the key commodities, click on PARTS INFORMATION, then PARTS LOOKUP. Type in the model type and serial number.
Page 32
For Key Commodities (Examples - hard disk drive, system board, microprocessor, LCD, and memory) Use the HMM as a back-up to PEW and eSupport to view the complete list of FRUs at the MT Model level. ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
• “Checkout guide” on page 26 – “Diagnostics using PC-Doctor for DOS” on page 26 – “Lenovo ThinkVantage Toolbox (Lenovo System Toolbox)” on page 29 – “PC-Doctor for Windows” on page 29 – “PC-Doctor for Rescue and Recovery” on page 29 –...
BIOS Setup Utility before you run PC-Doctor. To enter BIOS Setup Utility, do as follows: 1. Turn on the computer. ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Configuration utility for DOS. The utility is available on the following Web site: http://www.lenovo.com/support PC-Doctor cannot be used to test a device that is in the docking station, even if the computer supports the docking station.
Page 36
• Benchmark System • DOS Shell • Tech Support Form • Battery Rundown • View Test Log • Print Log • Save Log • Full Erase Hard Drive • Quick Erase Hard Drive ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Note: The latest Lenovo ThinkVantage Toolbox (Lenovo System Toolbox) is available at the following Web site: http://www.lenovo.com/support. To install the latest Lenovo ThinkVantage Toolbox (Lenovo System Toolbox) on the computer, follow the instructions on the Web site.
Page 38
System board 1. Diagnostics>CPU/Coprocessor 2. Diagnostics>Systemboard 3. If the ThinkPad X200 UltraBase™ is attached to the ThinkPad computer, detach it. Place the computer on a horizontal surface, and run Diagnostics>ThinkPad Devices>HDD Active Protection Test. Note: Do not apply any physical shock to the computer while the test is running.
You are here because the computer fails only when the ac adapter is used. • If the power problem occurs only when the ThinkPad X200 UltraBase is used, replace the UltraBase. • If the power-on indicator does not turn on, check the power cord of the ac adapter for correct continuity and installation.
3. Remove the battery pack (see “1020 Battery pack” on page 63). 4. Remove the backup battery (see “1090 Backup battery” on page 76). 5. Measure the voltage of the backup battery. See the following figure. ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 41
Wire Voltage (V dc) +2.5 to +3.2 Black Ground • If the voltage is correct, replace the system board. • If the voltage is not correct, replace the backup battery. • If the backup battery discharges quickly after replacement, replace the system board. Chapter 3 General checkout...
Supplemental Recovery Disc, click No. 9. When all of the data has been copied from the last disc in the set and has been processed, remove the disc and restart the computer. ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Attention: If the user HDP has been forgotten, check whether a master HDP has been set. If it has, it can be used for access to the hard disk drive. If no master HDP is available, neither Lenovo nor Lenovo authorized service technicians provide any services to reset either the user or the master HDP, or to recover data from the hard disk drive.
Attention: If User only mode is selected and the user HDP has been forgotten and cannot be made available to the service technician, neither Lenovo nor Lenovo authorized service technicians provide any services to reset the user HDPs or to recover data from the hard disk drive. The hard disk drive can be replaced for a scheduled fee.
7. Type the current master HDP in the Enter Current Password field. then leave the Enter New Password field blank, and press Enter twice. 8. Press F10. 9. Select Yes in the Setup Configuration window. Both user HDP and master HDP will have been removed. Power management To reduce power consumption, the computer has three power management modes: screen blank, sleep (standby in Windows XP), and hibernation.
If replacing a FRU does not solve the problem, put the original part back in the computer. Do not replace a nondefective FRU. This index can also help you determine, during regular servicing, what FRUs are likely to need to be replaced next. ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
A numeric error is displayed for each error detected in POST or system operation. In the displays, n can be any number. If no numeric code is displayed, check the narrative descriptions of symptoms. If the symptom is not described there, go to “Intermittent problems” on page 48. Note: For a device not supported by diagnostic codes in the ThinkPad Notebooks, see the manual for that device.
Page 50
Hard disk error—The hard disk is not working. 2. Load Setup Defaults in BIOS Setup Utility. 3. Hard disk drive. 4. System board. 021x Run interactive tests of the keyboard and the auxiliary Keyboard error. input device. ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 51
Table 2. Numeric error codes (continued) FRU or action, in sequence Symptom or error 0220 Load Setup Defaults in BIOS Setup Utility. Monitor type error—Monitor type does not match the one specified in CMOS. 0230 System board. Shadow RAM error—Shadow RAM fails at offset nnnn. 0231 1.
Page 52
Remove all but the reader that you set up for the More than one external fingerprint reader is attached. authentication. Power off and remove all but the reader that you set up within your main operating system. ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Ensure that your HDD or non-Lenovo hard disk drive (HDD), or an old is supported on this system and that the latest HDD generation IBM HDD which is not supported by this firmware is installed.
One long and two short beeps, and a blank or unreadable 1. System board. LCD. 2. LCD assembly. 3. DIMM. Two short beeps with error codes. POST error. See “Numeric error codes” on page 41. ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
If the LCD you are servicing has two or less visible defective pixels, it should not be considered faulty. However, if the LCD has three or more visible defective pixels, it will be deemed as defective by Lenovo and it should be replaced.
• Lenovo will not provide replacement if the LCD is within specification as we cannot guarantee that any replacement LCD will have zero pixel defects. • One pixel consists of R, G, B sub-pixels. Table 6. LCD-related symptoms Symptom or error...
Page 57
4. Turn on the computer. 5. Determine whether the problem has been solved. 6. If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU. 7. If the problem remains, replace the following FRUs one at a time (do not replace a nondefective FRU): a.
Page 60
(slow): and being charged. Blinking orange The battery is charged between 0% to 5% of the capacity. (rapid): AC power status Green: The computer is connected to the ac power supply. ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 61
Table 7. Status indicators (continued) Indicator Meaning Sleep (standby) Green: The computer is in sleep (standby) mode. status Blinking The computer is entering sleep (standby) mode or hibernation mode, green: or is resuming normal operation. Fingerprint reader Green: The fingerprint reader is ready to swipe. status only for X201 Tablet Blinking...
Page 64
Open the ThinkPad EasyEject Utility screen. Buttons for the following choices are displayed: • Eject ThinkPad PC from UltraBase: This button is displayed only if the ThinkPad computer has been attached to a ThinkPad X200 UltraBase. The computer can be detached from the ThinkPad X200 UltraBase.
CRU; and (2) you may be charged for the replacement CRU if Lenovo does not receive the defective part within thirty (30) days of your receipt of the replacement CRU. See your Lenovo Limited Warranty documentation for full details.
3. Select 1. Add S/N data from EEPROM. Follow the instructions on the screen. If the MTM and Product ID numbers differ from each other on the rear label, use what is shown for the Product ID field. See example below: ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
MTM on rear label: TTTT-CTO S/N SSSSSSS Product ID on rear label: TTTT-MMM (Use this number when setting Serial Number) In the example, the Serial Number to be input is '1STTTTMMMSSSSSSS'. Retaining the UUID The Universally Unique Identifier (UUID) is a 128-bit number uniquely assigned to your computer at production and stored in the EEPROM of your system board.
CRU; and (2) you may be charged for the replacement CRU if Lenovo does not receive the defective part within thirty (30) days of your receipt of the replacement CRU. See your Lenovo Limited Warranty documentation for full details.
Before servicing ThinkPad X200 Tablet and X201 Tablet Removing the SIM card: Some models of the ThinkPad X200 Tablet and X201 Tablet you are servicing might have the SIM card that the customer has been installed. If the computer you are servicing has the SIM card, remove it before you start the servicing.
The only exception to this is if the battery pack is physically damaged or a customer is reporting a possible safety issue. If ThinkVantage Toolbox or Lenovo System Toolbox is not installed in the computer, the customer should download this program before a non-physically damaged battery pack is replaced. Note that a physically damaged battery pack is non-warranty replacement.
• Before removing the drive, have the user make a backup copy of all the information on it if possible. • Never remove the drive while the system is operating or is in suspend mode. ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 73
Table 11. Removal steps of HDD cover, HDD, and HDD drive rubber rails or SSD and storage converter Step Screw (quantity) Color Torque Black 0.392 Nm Hard disk drive screw, M3 × 3 mm, wafer-head, nylon-coated (1) (4 kgfcm) Chapter 8 Removing and replacing a FRU...
Page 74
HDD and HDD rubber rails: When installing: The rubber rails on the hard disk drive must be attached to the replacement drive. Otherwise the drive cannot be installed properly. SSD and storage converter: ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Table 11. Removal steps of HDD cover, HDD, and HDD drive rubber rails or SSD and storage converter (continued) When installing: When you install the SSD in the storage converter, do as follows. 1040 DIMM For access, remove this FRU in order: •...
Page 76
Note: If only one DIMM is used on the computer you are servicing, the card must be installed in SLOT-0 ( ), but not in SLOT-1 ( For ThinkPad X201 Tablet: ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Table 12. Removal steps of dimm (continued) When installing: Insert the notched end of the DIMM into the socket. Press the DIMM firmly, and pivot it until it snaps into the place. Make sure that it is firmly fixed in the slot and does not move easily. 1050 Hinge caps For access, remove this FRU in order: •...
Open the LCD unit, and then remove the hinge cap (front). Close the LCD unit, and then remove the hinge cap (rear). 1060 Keyboard For access, remove this FRU in order: • “1020 Battery pack” on page 63 ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 79
Table 14. Removal steps of keyboard Step Icon Screw (quantity) Color Torque M2 × 6 mm, wafer-head, nylon-coated (4) Black 0.181 Nm (1.85 kgfcm) Chapter 8 Removing and replacing a FRU...
Page 80
1. Attach the keyboard connector firmly. 2. Make sure that the keyboard edges are under the frame as shown in this figure. Then press the keys to latch the keyboard firmly in place. ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Table 14. Removal steps of keyboard (continued) 3. To make sure that the front side of the keyboard is housed firmly, gently press the keys with your thumbs and try to slide the keyboard toward you. 4. Secure the keyboard by tightening the screws from the bottom side of the computer. 1070 Extension cable card For access, remove these FRUs in order: •...
When installing: Make sure that the connectors are attached firmly. 1080 Palm rest For access, remove this FRU in order: • “1020 Battery pack” on page 63 • “1060 Keyboard” on page 70 ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 83
Table 16. Removal steps of palm rest Step Icon Screw (quantity) Color Torque Black 0.181 Nm M2 × 6 mm, wafer-head, nylon-coated (5) (1.85 kgfcm) Chapter 8 Removing and replacing a FRU...
Use only the battery specified in the parts list for your computer. Any other battery could ignite or explode. For access, remove these FRUs in order: • “1020 Battery pack” on page 63 • “1060 Keyboard” on page 70 • “1080 Palm rest” on page 74 ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Table 17. Removal steps of backup battery When installing: Make sure that the battery connector is attached firmly. 1100 PCI Express Mini Card for wireless LAN/WiMAX For access, remove these FRUs in order: • “1020 Battery pack” on page 63 •...
Page 86
Note: Some models might have two antenna cables in step Step Screw (quantity) Color Torque 0.181 Nm M2 × 3.5 mm, wafer-head, nylon-coated (2) Silver (1.85 kgfcm) ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 87
Table 18. Removal steps of PCI Express Mini Card for wireless LAN/WiMAX (continued) When installing: • In models with wireless LAN card that has two antenna connectors, plug the gray cable into the jack labeled MAIN or M on the card, and the black cable into the jack labeled AUX or A. If the computer you are servicing has three cables, put the white cable in the cable protection tube.
In step , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow. ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 89
Table 19. Removal steps of PCI Express Mini Card for wireless WAN (continued) Step Screw (quantity) Color Torque M2 × 3.5 mm, wafer-head, nylon-coated (2) Silver 0.181 Nm (1.85 kgfcm) When installing: When you install the card, plug the red cable into the jack labeled MAIN on the card, and the blue cable into the jack labeled AUX.
, unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow. Step Screw (quantity) Color Torque M2 × 3.5 mm, wafer-head, nylon-coated (2) Silver 0.181 Nm (1.85 kgfcm) ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Table 20. Removal steps of Intel Turbo Memory Minicard or Wireless USB PCI Express Half-Mini Card (continued) When installing: In models with the Wireless USB PCI Express Half-Mini Card, plug the yellow cable into the jack on the card. 1130 Bluetooth daughter card (BDC-2.1) For access, remove these FRUs in order: •...
• “1080 Palm rest” on page 74 Table 22. Removal steps of keyboard bezel Torque Step Screw (quantity) Color M2 × 6 mm, wafer-head, nylon-coated (3) Black 0.181 Nm (1.85 kgfcm) ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 93
Table 22. Removal steps of keyboard bezel (continued) 0.181 Nm M2 × 3.5 mm, wafer-head, nylon-coated (4) Silver (1.85 kgfcm) Torque Step Screw (quantity) Color M2 × 2 mm, wafer-head, nylon-coated (1) Black 0.181 Nm (1.85 kgfcm) Rotate the LCD unit as shown in this figure. Chapter 8 Removing and replacing a FRU...
“1060 Keyboard” on page 70 • “1080 Palm rest” on page 74 • “1110 PCI Express Mini Card for wireless WAN” on page 80 • “1140 Keyboard bezel” on page 84 ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 95
Table 23. Removal steps of I/O card assembly Torque Step Screw (quantity) Color M2 × 3.5 mm, wafer-head, nylon-coated (1) Silver 0.181 Nm (1.85 kgfcm) When installing: Make sure that the speaker connector is attached firmly. Note: The cable is secured with a double-faced adhesive tape. Chapter 8 Removing and replacing a FRU...
“1010 Digitizer pen” on page 63 • “1020 Battery pack” on page 63 • “1060 Keyboard” on page 70 • “1080 Palm rest” on page 74 • “1140 Keyboard bezel” on page 84 ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 97
Table 24. Removal steps of USB sub card Step Screw (quantity) Color Torque 0.181 Nm M2 × 6 mm, wafer-head, nylon-coated (1) Silver (1.85 kgfcm) Turn the USB sub card over, an then disconnect the cable from the connector. Chapter 8 Removing and replacing a FRU...
• “1120 Intel Turbo Memory Minicard or Wireless USB PCI Express Half-Mini Card” on page 82 • “1140 Keyboard bezel” on page 84 Table 25. Removal steps of LCD assembly Step Screw (quantity) Color Torque ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 99
Table 25. Removal steps of LCD assembly (continued) Black 0.392 Nm M2.5 × 6 mm, wafer-head, nylon-coated (2) (4 kgfcm) Step Screw (quantity) Color Torque Black 0.392 Nm M2.5 × 6 mm, wafer-head, nylon-coated (2) (4 kgfcm) Before step , strip off the tapes securing the antenna cables, and release the cables from the cable guides of the frame.
Page 100
Table 25. Removal steps of LCD assembly (continued) ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Table 25. Removal steps of LCD assembly (continued) When installing: Route the antenna cables along the cable guides and secure them with the tapes. As you route the cables, make sure that they are not subjected to any tension. Tension could cause the cables to be damaged by the cable guides, or a wire to be broken.
Page 102
Table 26. Removal steps of DC-in connector, fan, digitizer pen case, and pen switch assembly (continued) Torque Step Screw (quantity) Color M2 × 3.5 mm, wafer-head, nylon-coated (1) Silver 0.181 Nm (1.85 kgfcm) ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 103
Table 26. Removal steps of DC-in connector, fan, digitizer pen case, and pen switch assembly (continued) Step Screw (quantity) Color Torque M2 × 3.5 mm, wafer-head, nylon-coated (1) Black 0.181 Nm (1.85 kgfcm) In step , remove the digitizer pen case assembly. Torque Step Screw (quantity)
Page 104
Table 26. Removal steps of DC-in connector, fan, digitizer pen case, and pen switch assembly (continued) Torque Step Screw (quantity) Color M2 × 3.5 mm, wafer-head, nylon-coated (6) Silver 0.181 Nm (1.85 kgfcm) When installing: Attach the wireless radio switch as shown in the figure ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 105
Table 26. Removal steps of DC-in connector, fan, digitizer pen case, and pen switch assembly (continued) Turn the system board over, and then disconnect the DC-in connector, the fan connector, and the pen switch connector from the system board. When installing: Make sure that the DC-in connector, the fan connector, and the Pen switch connector are attached to the system board firmly.
• Be careful not to drop the system board on a bench top that has a hard surface, such as metal, wood, or composite. • If a system board is dropped, you must test it, using PC-Doctor for DOS, to make sure that the HDD ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 107
Table 27. Removal steps of system board and ExpressCard slot assembly Following components soldered on the system board are extremely sensitive. When you service the system board, avoid any kind of rough handling. For ThinkPad X200 Tablet: ICH (I/O Controller Hub) MCH (Memory Controller Hub) Accelerometer chip for the HDD Active Protection System™...
Page 108
Table 27. Removal steps of system board and ExpressCard slot assembly (continued) Bottom For ThinkPad X201 Tablet: PCH (Platform Controller Hub) Accelerometer chip for the HDD Active Protection System Bottom ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 109
Table 27. Removal steps of system board and ExpressCard slot assembly (continued) Note: The ExpressCard slot assembly is attached to the system board. For ThinkPad X200 Tablet: For ThinkPad X201 Tablet: Step Screw (quantity) Color Torque 0.181 Nm M2 × 3.5 mm, wafer-head, nylon-coated (1) Silver (1.85 kgfcm)
Table 28. Removal steps of base cover and speaker assembly Remove the speaker assembly from the base cover assembly. When installing: Route the speaker cables along the cable guides as shown in this figure. ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 111
Applying labels to the base cover: The new base cover FRU is shipped with a kit containing labels of several kinds. When you replace the base cover, you need to apply the following labels: Homologation label Product label Non-mercury label Note: If the computer you are servicing is an LED-backlight LCD model, you need to paste this label so that the notice for mercury on the product label is covered.
– “1020 Battery pack” on page 63 Table 29. Removal steps of LCD front bezel for protection plate LCD model Protection plate LCD model: Step Screw cap Screw (quantity) Color Torque ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 113
Table 29. Removal steps of LCD front bezel for protection plate LCD model (continued) Black 0.392 Nm M2.5 × 8 mm, wafer-head, nylon-coated (5) (4 kgfcm) When installing: Attach the fingerprint reader connector firmly. Table 30. Removal steps of LCD front bezel for touch panel LCD model or direct-bonding glass LCD model Touch panel LCD model or direct bonding glass LCD model: Chapter 8 Removing and replacing a FRU...
Page 114
, detach the claws. Then remove the LCD front bezel. Note: The LCD front bezel is secured with a double-faced adhesive tape. When installing: Make sure that all the claws are attached firmly. ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Table 30. Removal steps of LCD front bezel for touch panel LCD model or direct-bonding glass LCD model (continued) When installing: Make sure that attach the fingerprint reader connector firmly. 2020 Micro-Processor card For access, remove these FRUs in order: •...
Page 116
Black 0.181 Nm (1.85 kgfcm) Touch panel LCD model or direct-bonding glass LCD model Torque Step Screw (quantity) Color M2 × 3.5 mm, wafer-head, nylon-coated (3) Silver 0.181 Nm (1.85 kgfcm) ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Table 31. Removal steps of Micro-Processor card (continued) Black 0.181 Nm M2 × 3 mm, height 5.5 mm, stud, nylon-coated (1) (1.85 kgfcm) When installing: Make sure that the connector is attached firmly. 2030 Inverter card For access, remove these FRUs in order: •...
Table 33. Removal steps of hinge Step Screw (quantity) Color Torque Black 0.392 Nm M2.5 × 6 mm, wafer-head, nylon-coated (2) (4 kgfcm) Detach the hinge from the LCD rear cover, and gently pull the cables out through the guide hole in the hinge. Pull them all at once.
Page 120
M2 × 3 mm, flat-head, nylon-coated (6) (1.85 kgfcm) — M2 × 3.5 mm, wafer-head, nylon-coated (3) Silver 0.181 Nm (1.85 kgfcm) In step , detach the claws. Then remove the LCD panel. ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 121
Table 34. Removal steps of LCD panel and LCD cable for protection plate LCD model (continued) When installing: Make sure that all the claws are attached firmly. Note: Step is only for models with the integrated camera. For models without the integrated camera, skip step Chapter 8 Removing and replacing a FRU...
Page 122
Table 35. Removal steps of LCD panel, LCD bracket L and R, and LCD cable for touch panel LCD model or direct-bonding glass LCD model Touch panel LCD model or direct bonding glass LCD model: Step Screw (quantity) Color Torque ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 123
Table 35. Removal steps of LCD panel, LCD bracket L and R, and LCD cable for touch panel LCD model or direct-bonding glass LCD model (continued) M2 × 3.5 mm, wafer-head, nylon-coated (5) Silver 0.181 Nm (1.85 kgfcm) Note: Step is only for models with the integrated camera.
Page 124
Turn the LCD panel over, and then remove the LCD cable from the LCD panel. Single touch panel LCD model or direct bonding glass LCD model: When installing: Make sure that the LCD cable connector are attached firmly. ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Table 35. Removal steps of LCD panel, LCD bracket L and R, and LCD cable for touch panel LCD model or direct-bonding glass LCD model (continued) Multitouch panel LCD model: When installing: Make sure that the LCD cable connector are attached firmly. 2060 Integrated camera For access, remove these FRUs in order: •...
“2030 Inverter card” on page 109 • “2040 Hinges” on page 110 • “2050 LCD panel, LCD bracket L and R, and LCD cable” on page 111 • “2060 Integrated camera” on page 117 ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 127
Table 37. Removal steps of LCD rear cover and wireless antenna cables Note: Step is only for protection plate LCD model. For touch panel LCD model or direct-bonding glass LCD model, skip step Step Screw (quantity) Color Torque M2 × 3.5 mm, wafer-head, nylon-coated (2) Silver 0.181 Nm (1.85 kgfcm)
Page 128
Table 37. Removal steps of LCD rear cover and wireless antenna cables (continued) In step , release the antenna cables from the cable guides of the rear cover. Remove the center latch from the LCD rear cover. ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 129
Table 37. Removal steps of LCD rear cover and wireless antenna cables (continued) Torque Step Screw (quantity) Color M2 × 3.5 mm, wafer-head, nylon-coated (2) Silver 0.181 Nm (1.85 kgfcm) When installing: Place the antenna assembly as shown in this figure. Wireless WAN antenna, AUX (blue) Wireless LAN antenna, AUX (black) Wireless USB antenna (yellow)
Page 130
Attention: As you route the antenna cables, make sure that they are not subjected to any tension. Tension could cause the cables to be damaged by the cable guides, or a wire to be broken. ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Chapter 9. Locations This chapter presents the location of ThinkPad X200 Tablet and X201 Tablet features and hardware. Front view Center latch Integrated camera (for some models) Universal serial bus (USB) connector Tablet digitizer pen Hard disk drive (HDD) or solid state drive (SSD)
Note: For the description of each indicator, see Chapter 5 “Status indicators” on page 51. ExpressCard slot Wireless radio switch Universal Serial Bus (USB) connector RJ-45 (Ethernet) connector External monitor connector AC power connector Security key hole ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Rear view (tablet mode) Tablet buttons Fingerprint reader Status indicators Note: For the description of each indicator, see Chapter 5 “Status indicators” on page 51. Chapter 9 Locations...
(1) return instructions, a prepaid shipping label, and a container will be included with the replacement CRU; and (2) you may be charged for the replacement CRU if Lenovo does not receive the defective part within thirty (30) days of your receipt of the replacement CRU. See your Lenovo Limited Warranty documentation for full details.
Extension cable card assembly for X201 Tablet 75Y4059 USB sub card assembly for X200 Tablet 42W8086 N 75Y4060 USB sub card assembly for X201 Tablet Pen switch assembly 45N4817 Digitizer pen case assembly 45N3146 Backup battery 92P1210 ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 173
Table 39. Parts list - 12.1-in. WXGA TFT for touch panel LCD or direct-bonding glass LCD (continued) FRU no. 60Y4166 N LCD bracket L and R for multitouch panel • 4184-CTO • 7448-CTO, 34x, 36x, 3Dx, 3Ex, 3Hx, 3Kx, 3Nx •...
Page 175
Table 39. Parts list - 12.1-in. WXGA TFT for touch panel LCD or direct-bonding glass LCD (continued) FRU no. 43Y9830 N Wireless LAN/WAN antenna assembly • 4184-CTO, E4x, E6x, E7x, E9x, EFx, EGx, ENx, ESx, F4x, F5x, F7x, F8x, FBx, FCx, FFx, FGx, GMx, GNx •...
Page 176
LCD rear cover assembly for touch panel for X201 Tablet 75Y4601 N LCD rear cover assembly for direct-bonding glass 60Y5514 N LCD rear cover assembly for direct-bonding glass for X201 Tablet 75Y4602 N Hinge 60Y4609 N Hinge caps 45N3125 N ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
2-pin AC (90W, 100 - 240 V) and 3-pin DC (90W, 10.5 - 18V) combo adapter 41R0140 Power cords A ThinkPad power cord for a specific country or region is usually available only in that country or region: ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Table 44. Parts list - 2-pin power cords FRU no. Country or region Argentina 42T5020 42T5105 • models -CTO, xxY Brazil 42T5180 42T5183 • models -CTO, xxP Canada, U.S. 42T5008 42T5093 • models -CTO, xxF, xxL, xxS, xxU Japan 42T5014 42T5099 •...
Table 47. Parts list - Windows XP Tablet (32 bit) recovery DVDs Language English 76Y1314 English (modem-disabled) 76Y1313 French 76Y1304 76Y1305 German Italian 76Y1306 Japanese 76Y1307 Korean 76Y1308 Russian 76Y1310 76Y1309 Russian (English-enabled) Simplified Chinese 76Y1302 76Y1311 Spanish Swedish 76Y1312 76Y1303 Traditional Chinese Windows Vista Home Premium (32 bit) DVDs...
English, French, German, and Dutch (in Belgium and Luxemburg) 58Y3024 58Y3026 English, French, German, and Italian (in Switzerland) French 58Y3002 German 58Y3004 58Y3003 Greek Hebrew 58Y3005 Hungarian 58Y3007 Italian 58Y3008 Japanese 58Y3009 Korean 58Y3010 ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Table 49. Parts list - Windows Vista Business (32 bit) DVDs (continued) Language Norwegian 58Y3011 Polish 58Y3012 Portuguese 58Y3013 Romanian 58Y3015 Russian 58Y3016 58Y3014 Russian (English-enabled) Serbian-Latin 58Y3020 Simplified Chinese 58Y2998 Slovak 58Y3017 Slovenian 58Y3018 Spanish 58Y3019 Traditional Chinese 58Y2999 Traditional Chinese (Hong Kong S.A.R.) 58Y3006 Turkish...
58Y3050 58Y3052 German Greek 58Y3051 Hebrew 58Y3053 Hungarian 58Y3055 Italian 58Y3056 Norwegian 58Y3057 Polish 58Y3058 Romanian 58Y3059 58Y3063 Serbian-Latin Simplified Chinese 58Y3046 58Y3060 Slovak Slovenian 58Y3061 58Y3062 Spanish Traditional Chinese 58Y3047 ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Table 52. Parts list - Windows Vista Ultimate (32 bit) DVDs (continued) Language 58Y3054 Traditional Chinese (Hong Kong S.A.R.) Turkish 58Y3064 Windows 7 Home Basic (32 bit) DVDs Windows 7 Home Basic (32 bit) is preinstalled as the operating system in the following models: •...
Traditional Chinese (Hong Kong S.A.R.) 76Y1439 Windows 7 Home Premium (64 bit) DVDs Windows 7 Home Premium (64 bit) is preinstalled as the operating system in the following models: • 4184-CTO • 7448-CTO • 7449-CTO ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
• 7450-CTO • 7453-CTO • 2263-CTO • 2266-CTO Table 56. Parts list - Windows 7 Home Premium (64 bit) DVDs Language English 58Y3936 English (for India) 58Y3932 Japanese 58Y3933 Polish 58Y3934 58Y3931 Simplified Chinese Turkish 58Y3935 • 0053-CTO • 0831-CTO •...
• 3239-CTO Table 61. Parts list - Windows 7 Professional (64 bit) DVDs Language Danish 76Y1488 English 76Y1497 English (for India) 76Y1489 76Y1496 English (modem-disabled) French 76Y1490 German 76Y1491 Italian 76Y1493 ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any Lenovo intellectual property right may be used instead.
All information contained in this document was obtained in specific environments and is presented as an illustration. The result obtained in other operating environments may vary. Lenovo may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you.
Page 203
Intel Core 2 Solo Other company, product, or service names may be the trademarks or service marks of others. Chapter 10 Parts list...