Global ( G L B ) - Korg WAVEDRUM Owner's Manual

G L b
Global ( )
For details on how to access parameters, refer to "Basic editing procedure" (See page 8).
Page#.
Button 1
Parameter
P a n
L 5 0 . . . r 5 0
Specifies the pan follow-
ing the delay effect.
1. Common
values place the sound
L
Co
( ) to the left, values to the
r
right, and 00 places the
sound in the center.
(Default Value: 0)
L o
0 0 0 . . . 1 0 0
The input signal from the
head is attenuated when
2. Head
it falls below a specified
Calibration
level. This parameter
H. ca specifies the threshold
( )
level below which this
will occur (See page 29).
(Default Value: 7)
L o
0 0 0 . . . 1 0 0
The input signal from the
rim is attenuated when it
3. Rim
falls below a specified
Calibration
level. This parameter
r. ca specifies the threshold
( )
level below which this
will occur (See page 29).
(Default Value: 7)
U a L
0 0 0 . . . 1 0 0
Indicates the current
value of the pressure sen-
4. Pressure sor. Apply pressure on
the head, note the mini-
Calibration
mum and maximum
P. ca
( )
readings, and adjust the
. and .
P L o P H i
if necessary (See
page 29).
Adjusting the volume of a device connected to the
AUX IN connector
1. As described in "Connecting audio devices" and
"Turning the power on" (See page 6), connect your
audio device to the WAVEDRUM's AUX IN jack and
turn on the power.
2. Hold down the BANK/MODE button and press button
4 to enter Global mode.
3. Press the BANK/MODE button (several times). The
display will indicate Co (Common).
4. Press button 2 to make the display indicate
the value.
5. Use the controls of the connected audio device and the
WAVEDRUM's mix level to adjust the volume. Turn the
VALUE knob to adjust the WAVEDRUM's mix level.
note: We recommend that you raise the mix level of the AUX
IN jack only when you're using it. However if you are using
it all the time, and would like to leave the mix level raised,
you can save this setting. Press the WRITE button twice to
save the setting. For more details on saving, refer to page 9.
Button 2 *
A . l n
0 0 0 . . . 1 0 0
Specifies the AUX IN
mix level.
(Default Value: 0)
S E n
0 0 0 . . . 1 0 0
Specifies the sensitivity
with which your striking
force on the head will
affect the head PCM
instrument or the PCM
instrument of a double-
size algorithm.
(Default Value: 20)
S E n
0 0 0 . . . 1 0 0
Specifies the sensitivity
with which your striking
force on the rim will
affect the rim PCM
instrument.
(Default Value: 20)
P. L o
Specifies the minimum
value that is detected as
pressure applied to the
head. (Default Value: 5)
settings
A. I n and
Button 3 *
L o P
0 0 1 . . . 1 0 0
Selects the loop phrase
that will be played.
(Default Value: 0)
- - -
- - -
P. H i
0 0 . . . 9 9 0 0 1 . . . 1 0 0
Specifies the maximum
value that is detected as
pressure applied to the
head.
(Default Value: 100)
Playing back a loop phrase
1. Hold down the BANK/MODE button and press button
4 to enter Global mode.
2. Press the BANK/MODE button (several times). The
display will indicate Co (Common).
3. Press button 4. The loop phrase will sound. Each time
you press the button, the status will alternate between
start ( P L y ) and stop ( o F F ).
4. To adjust the volume, turn the VALUE knob when
button 4 selected.
5. To switch the loop phrase, press button 3 to make the
display indicate L o P , and turn the VALUE knob (See
Voice Name List).
• If you want to play a different program, hold down
the BANK/MODE button and press button 1 to enter
Live mode, and then switch the program. To stop
playback, hold down the BANK/MODE button and
press button 4 to enter Global mode, and press button
4 in the Co (Common) page.
note: You can't change the playback speed of the loop phrase.
Parameter list Global ( G L b )
Button 4 *
/
P L y , o F F
000. . . 1 00
Plays the loop phrase.
Play/off will alternate
each time you press but-
ton 4. While playing, you
can use the VALUE knob
to adjust the volume.
(Default Value: off/38)
- - -
- - -
- - -
15