Lead Free Information; Attachment & Detachment Of Mdf61 Connector; Attachment, Detachment & Confirmation Of Lock; Condition Of Jst Ibh Connector - Sony KDL-22BX300 Service Manual
Hide thumbs
Also See for KDL-22BX300:
- Operating instructions manual (63 pages) ,
- Service manual (32 pages) ,
- Quick setup manual (2 pages)
Table of Contents
Advertisement
KLV-22, 26, 32 BX300, 40 BX400
1-5. Lead Free Information
The circuit boards used in these models have been processed
using Lead Free Solder. The boards are identified by the LF
logo located close to the board designation.
Figure 2: LF logo
The servicing of these boards requires special precautions. It
is strongly recommended to use Lead Free Solder material in
order to guarantee optimal quality of new solder joints. Lead
Free Solder is available under the following part numbers:-
P
a
t r
n
u
m
b
r e
7
6 -
4
0
0 -
0
5
1 -
9
7
6 -
4
0
0 -
0
5
2 -
0
7
6 -
4
0
0 -
0
5
2 -
1
7
6 -
4
0
0 -
0
5
2 -
2
7
6 -
4
0
0 -
0
5
2 -
3
7
6 -
4
0
0 -
0
5
2 -
4
7
6 -
4
0
0 -
0
5
2 -
5
7
6 -
4
0
0 -
0
5
2 -
6
Due to high melting point of Lead Free Solder, the soldering
iron tip temperature needs to be set to 370 degrees
centigrade. This requires soldering equipment capable of
accurate temperature control coupled with a good heat
recovery characteristics.
For more information on the use of Lead Free Solder,
please refer to http://www.sony-training.com
1-6. Attachment & Detachment of MDF61 Connector
(If applicable for these models)
a) Insertion
(1) Hold the center of a
connector.
RM-GA019
Figure 3: LF logo on circuit board
D
a i
m
t e
r e
R
e
m
0
3 .
mm
0
2 .
5
0
4 .
m
m
0
5 .
0
0
5 .
m
m
0
5 .
0
m
0
6 .
m
0
2 .
5
0
8 .
m
m
1
0 .
0
1
0 .
m
m
1
0 .
0
1
2 .
m
m
1
0 .
0
1
6 .
m
m
1
0 .
0
(2) Press the center of the
(3) Slide the slider to lock the
connector to insert it.
connector.
Lock
b) Detachment
(1) Slide the slider to release
the slider lock.
1-7. Attachment, Detachment & Confirmation of Lock
Condition of JST IBH Connector
(If applicable for these models)
a
k r
s
Attention: This is a SAFETY CRITICAL PROCESS.
Kg
Kg
Kg
a) Attachment
Kg
Kg
(1) Press the center of the connector to insert it.
Kg
Kg
Kg
(2) Press position
(NG for red marking portion)
(3) Prohibited matter (Refer Figure A~C explanation)
Figure A
– 4 –
(2) Press the center lock tab
to release the lock and pull
the connector up.
Unlock
Figure A: Do not press lock
Figure B: Do not press the
Figure C: Do not press the side
Figure C
Figure B
portion.
front side of the
connector.
of the connector.
- Quick Links:
- Service Manual
- Klv-32Bx300
- Klv-40Bx400
Hide quick links:
Advertisement
Table of Contents
