Page 2
Barco nv Media & Entertainment Division Noordlaan 5, B-8520 Kuurne Phone: +32 56.36.82.11 Fax: +32 56.36.883.86 E-mail: sales.events@barco.com Visit us at the web: www.barco.com Printed in Belgium...
The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning, at latest 30 days after the transfer of risks. In the event of justified notice of complaint, Barco can repair the fault or provide a replacement at its own discretion within an appropriate period.
GNU-GPL code If you would like a copy of the GPL source code contained in this product shipped to you on CD, please contact Barco. The cost of preparing and mailing a CD will be charged.
Restricted access location The FLM R20+ Performer may only be installed in a restricted access location, due to the temperature rise of parts of the equipment (air outlet).
• The power cord of the FLM R20+ Performer is equipped with a 3-wire grounding plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type EN60-309 power outlet. This is a safety feature. Mains power cord with EN60-309...
Page 11
Caution: High pressure lamp may explode if improperly handled. Refer servicing to qualified service personnel. The customer should never attempt to disassemble the lamp casing or to dispose of the lamp casing other than by returning it to Barco. •...
flammable or combustible materials are present. The exclusion zone must be not less than 40 cm (16”) for all Barco DLP projectors. The exclusion zone on the lens side must be at least 2 meter (80”).
Projector weight Do not underestimate the weight of one Barco FLM R20+ Performer, which is about ±100 kg (±225 lb.). Be sure that the table or truss installation on which the projector(s) has to be installed is capable of handling five (5) times the complete load of the complete system.
Note: The two smaller carton boxes contain the manuals, the remote control unit (RCU), two standard batteries size AA and four rigging clamps for projector suspension. Image 2-2 R5976921 FLM R20+ PERFORMER 15/03/2010...
This check should confirm that there are no broken knobs or connectors, that the cabinet and panel surfaces are free of dents and scratches, and that the meter face and operating panel are not scratched of cracked. The Barco sales and service office should be notified as soon as possible.
Introduction of the FLM flight case The FLM flight case is designed to transport the FLM R20+ Performer in a safe and secure manner. The four caster wheels, provided with breaks, and the eight handles make the FLM flight case easy to handle. The floor of the flight case wagon is equipped with two small covered compartments to store the remote control and the rigging clamps.
2. General AUDIENCE FLOOR Image 2-6 Rear projection The projector is installed, either in a table mount or ceiling mount configuration, at the other side of the screen opposite the audience. AUDIENCE BACKSTAGE FLOOR Image 2-7 R5976921 FLM R20+ PERFORMER 15/03/2010...
field of view (F) as illustrated below. Within these shift ranges the projector and lens perform excellently. Configuring the projector outside these shift ranges will result in a slight decline of image quality. R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 19
Always respect the allowed tilt range of the projector. Neglecting this will result in lamp flicker, which reduces the light output and the life span of the lamp substantially. Furthermore, in the long term, the possibility exist that the lamp explodes. R5976921 FLM R20+ PERFORMER 15/03/2010...
Image 2-11 The FLM R20+ Performer has 5 air inlet channels and one air outlet. The air outlet is located at the rear of the projector. The air inlets are located at the front, bottom, top and right side of the projector.
The remote control unit (A) of the FLM projector is equipped with a rugged case (B) and an XLR adaptor (C). The remote control unit can be used wired via mini-jack or via rugged XLR. Note that the backlight, of the remote control unit, illuminate continuously when wire connected. Image 3-1 Remote control unit (RCU). Rugged case. R5976921 FLM R20+ PERFORMER 15/03/2010...
• Danger of explosion if battery is incorrectly installed. • Replace only with the same or equivalent type recommended by the manufacturer. • Disposal of used batteries must be done according to the manufacturer’s instruction. R5976921 FLM R20+ PERFORMER 15/03/2010...
1. Connect a cable with XLR plug into the XLR adaptor. 2. Connect the other end of the cable with your FLM R20+ Performer. 3. Push the XLR adaptor completely against the rugged case of the remote control unit, as illustrated in the left image below, for wired communication.
RCU with rugged case and XLR adaptor The RCU will send the commands via the cable connected with the XLR pushed in “WIRED” and wired adaptor to the projector. Backlight illuminates continuously when wire is connected. Infra red disabled. Image 3-8 R5976921 FLM R20+ PERFORMER 15/03/2010...
Available lenses for the FLM R20+ Performer projector The TLD and the TLD HB (High Brightness) lens series can be used on the FLM R20+ Performer projector. Note that there is no physical difference on the outside between the TLD and the TLD HB lenses with corresponding focal length. The TLD HB lenses are recommended on the FLM R20+ Performer projector.
4. Ensure that the lens holder stands in the On-Axis position (horizontal and vertical mid position). Note: The lens holder is placed default in the On-Axis position at factory. 5. Gently insert the lens in such a way that the lens connector matches the socket (B). Image 3-19 R5976921 FLM R20+ PERFORMER 15/03/2010...
1. Support the lens with one hand while you unlock the lens holder by sliding the lock handle towards the “unlocked” position as illustrated. Image 3-21 2. Gently pull the lens out of the lens holder. R5976921 FLM R20+ PERFORMER 15/03/2010...
3. Turn the adjustable feet in or out until the projected hatch pattern is perfectly rectangle shaped and leveled. Image 3-23 When this is achieved, the projector is set horizontal and vertical at right angles to the screen. Image 3-24 R5976921 FLM R20+ PERFORMER 15/03/2010...
The rigging clamps (C) can be attached to those rigging points, which allows an easy and fast physical setup of the projector in a hanging configuration. Image 3-27 Necessary tools • 24 mm open ended spanner. • 17 mm open ended spanner. R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 31
(B) on the rigging clamp against the rigging point using a 17 mm open ended spanner. Warning: Always use four (4) rigging points, equally spread, to suspend the projector. Image 3-30 4. Place all four rigging clamps in open position as illustrated. R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 32
7. Lock all four rigging clamps. 8. Install a safety chain (S) around both sides of the carrying handle and around the truss. Image 3-33 9. Lift up the truss with attached projector to the desired height. R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 33
3. Physical installation Proceed with the alignment procedure, see "Alignment of a ceiling mount FLM projector", page 26. R5976921 FLM R20+ PERFORMER 15/03/2010...
In case of stacking projectors for a ceiling mount configuration, first turn the projectors upside down before placing the projectors on top of each other. Image 4-1 3. Attach the two projectors together by closing all three interlocking adapters as illustrated. Image 4-2 R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 36
Always use both safety cables of the lowest projector to secure a stacked projector in a ceiling mount configuration. How to open an interlocking adapter ? 1. Open an interlocking adaptor as illustrated. Image 4-5 R5976921 FLM R20+ PERFORMER 15/03/2010...
8 mm Allen key. The screw Q is located behind the cover of the lamp, just above the volt meter. Adjust until the outline of the hatch pattern is most symmetric with the reference hatch pattern. Note: See procedure "Removal of the lamp cover", page 195, to access the skew adjustment screw Q. R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 38
8. If necessary, repeat from step 2 until the hatch pattern of the stacked projector is perfectly aligned with the hatch pattern of the reference projector. In case of a triple stacked table mount projector configuration adjust and align first the bottommost projector (reference), than the projector in the middle and finally the uppermost projector. R5976921 FLM R20+ PERFORMER 15/03/2010...
4. Connect the other end of the power cord with the local power net. Caution: Ensure that the power net meets the power requirements of the projector, which are: 200-240 VAC, 50–60 Hz, 16 amps at 230 VAC. R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 40
first to access this spare power plug, see "Removal of the lamp cover", page 195. Note that only qualified technical personnel may install a new power plug. HAN Q4/2 + Image 5-3 Pin configuration power plug HAN Q4/2 + PE. R5976921 FLM R20+ PERFORMER 15/03/2010...
5. Connections The FLM R20+ Performer is standard equipped with one 5 cable input module, one HDSDI - SDI input module and one DVI input module. Input slot number 4 (lowermost) is covered with a input cover plate. For more information about the FLM input modules see chapter “Specifications”.
Page 43
RS232/422 serial communication The communication interface of the FLM R20+ Performer supports RS232 and RS422 serial communication. You can use the RS232/RS422 input port (O) to connect a local PC to your FLM projector. This way you can configure and control your FLM projector from your local PC.
Page 44
RJ45 cable connector. Straight (most common) as well as cross linked network cables can be used. The 2 ports are functionally identical. Both ports are connected via the projector hub (Auto sensing enabled). 10/100 Base-T — RJ45 port Pin Description TXD+ TXD- RXD+ — — RXD- R5976921 FLM R20+ PERFORMER 15/03/2010...
files from the projector without network connection. An USB-stick is plugged into the USB port and files can be transferred from or to the projector using the local or remote control unit. Note that the USB-stick has to be FAT16 compatible. Card bus connector (PCMCIA) No cards supported yet. R5976921 FLM R20+ PERFORMER 15/03/2010...
• switching to "pause" (blanked picture, full power for immediate restarting) • direct access to all connected sources. Terminology overview Overview The following table gives an overview of the different functionality of the keys. R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 48
Direct input selection or menu short cuts or numeric entries Lens zoom/focus Zoom and focus controls of the lens Lens shift Shift control of the lens, to shift the lens up/down or left/right Picture controls Use these buttons to obtain the desired picture level. R5976921 FLM R20+ PERFORMER 15/03/2010...
When ’1’ is visible, the projector is switched on. The projector starts up in standby. The menus are accessible via the local LCD panel. To display an image, the standby key must be pressed once. R5976921 FLM R20+ PERFORMER 15/03/2010...
1. Press Standby to switch the projector to standby. A cool-down counter (after cooling) starts counting down for 5 minutes (only visible on the local LCD panel). During this period the fans are still running. A restart is possible during this period. R5976921 FLM R20+ PERFORMER 15/03/2010...
Remote Control (A) Image 6-4 IR control via the reflective screen Remote control Screen Front IR-sensor Hardwired Remote Input 1. Plug one end of the remote cable in the connector on the bottom of the RCU. R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 52
Wa rn in g I R P US H P US H RS 23 2/ 422 i n U SB P C Ca rd 45° 45° 45° 45° 45° 45° Image 6-6 RCU to one of the IR sensors R5976921 FLM R20+ PERFORMER 15/03/2010...
Press the LENS key to switch to another pattern. Different patterns are available. Quick shift adjustment 1. Press the LENS key on the remote control or local keypad. The zoom/focus menu will be displayed. Image 6-8 2. Press ENTER. R5976921 FLM R20+ PERFORMER 15/03/2010...
Press on the PIP key on the remote control or the local keypad to activate the Load layout window. Use the ▲ ▼ key to scroll to the desired layout and press ENTER to activate. Select Main full screen to switch off PIP. R5976921 FLM R20+ PERFORMER 15/03/2010...
1. Press Menu to activate the menus and select with the ▲ or ▼ key Projector Control and press ENTER. 2. Select with the ▲ or ▼ key Language and press ENTER. The language menu opens. 3. Select with the ▲ or ▼ key the desired language and press ENTER to activate. R5976921 FLM R20+ PERFORMER 15/03/2010...
Note: That address can be any digit between 0 and 9. The LED on the remote control must lit up while pressing a digit key. Otherwise the address is not entered in the remote control. R5976921 FLM R20+ PERFORMER 15/03/2010...
To select the source for the picture in picture window, press Window button until PiP window is activated and then select the desired source with the digit keys. To select the source for the main window, press Window button until the main window is activated and then select the desired source with the digit keys. R5976921 FLM R20+ PERFORMER 15/03/2010...
Set the RCU address to the common address and press Freeze for 5 seconds. All projectors go to stand-by without the risk of restart. When pressing shortly on Freeze, the current image is frozen. R5976921 FLM R20+ PERFORMER 15/03/2010...
To start up the adjustment mode, use the remote control or the local keypad. How to start up? 1. Press Menu on the remote control (RCU) or on the local keypad to start up the Adjustment mode. R5976921 FLM R20+ PERFORMER 15/03/2010...
The digit keys 5 to 9 can be customer programmed to directly open a pre-stored menu. That menu can be any independent menu out of the list of menu. A menu which is built up by the content of a previous menu cannot be stored behind a shortcut. R5976921 FLM R20+ PERFORMER 15/03/2010...
When restarting the projector from stand-by, the menu memory is reset. After re-opening the main menu and selecting an item, the previous selected sub item of that selected item is highlighted and can be opened just by pressing ENTER. R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 62
7. Start up of the Adjustment Mode R5976921 FLM R20+ PERFORMER 15/03/2010...
The projector has 4 input slots and these slots can be filled up in a random order with the available modules. Identical modules are allowed. For more information about the available input modules and how to install, see "Input source connections", page 37. R5976921 FLM R20+ PERFORMER 15/03/2010...
When e.g. RGB AUTO is selected, the projector discovers itself which type of RGB signal is connected to it and loads the correct settings. For RGB selections, advanced settings are possible. To adjust these advanced settings, use the ▲ or ▼ key to select Advanced settings and press ENTER. The advanced settings menu opens: R5976921 FLM R20+ PERFORMER 15/03/2010...
3. Use the ▲ or ▼ key to select Input locking and press ENTER. The input locking window is displayed. The actual selected locking method is indicated by an arrow. 4. Use the ▲ or ▼ key to select the desired locking and press ENTER. R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 66
When Automatic or specific input is selected (arrow in front of it) and then the Options are selected, the following menu appears: Image 8-11 Use the ▲ or ▼ key to select Genlock and press ENTER to toggle between On and Off. R5976921 FLM R20+ PERFORMER 15/03/2010...
3. Use the ▲ or ▼ key to select Minimum delay and press ENTER to toggle between [On] and [Off]. Image 8-13 Image 8-12 Native resolution What can be done The aim here is to always show the resolution of the source independently of the resolution of the DMD panels. R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 68
[On] : images displayed in native resolution [Off] : images scaled to fill the complete screen Image 8-16 Image 8-15 When native resolution is on, some other menus such as Aspect ratio, timings are greyed out. R5976921 FLM R20+ PERFORMER 15/03/2010...
When no signal available, a blue or black background color can be displayed or the projector can be shutdown with a certain retarding time. 8.7.1 Background color How to change the color 1. Press MENU to activate the menus. R5976921 FLM R20+ PERFORMER 15/03/2010...
2. Use the ▲ or ▼ key to select Input and press ENTER. The Input menu is displayed. 3. Use the ▲ or ▼ key to select Shutdown time and press ENTER. 4. Use the ▲ or ▼ key to change the value. R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 71
8. Input menu enter the desired value with the keyboard. When trying to exceed the maximum allowed value, the system will set it back to the maximum value. Image 8-29 Image 8-28 Image 8-27 R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 72
8. Input menu R5976921 FLM R20+ PERFORMER 15/03/2010...
Color temperature Projector white Computer 9300K Video 6500K Film 5400K Broadcast 3200K Custom balance Input balance Aspect ratio 16/9 2.35 1.88 1.78 Custom Timings Total pixels Active pixels Horizontal start Period Total lines Active lines R5976921 FLM R20+ PERFORMER 15/03/2010...
3. Use the ▲ or ▼ key to select Image settings and press ENTER. 4. Use the ▲ or ▼ key to select Brightness and press ENTER. The Brightness progress bar appears. 5. Use ◄ or ► to change the brightness. R5976921 FLM R20+ PERFORMER 15/03/2010...
4. Use the ▲ or ▼ key to select Saturation and press ENTER. The Saturation progress bar appears. 5. Use ◄ or ► to change the color saturation. The higher the value, the higher the color saturation. Image 9-12 Image 9-11 Image 9-13 Image 9-14 R5976921 FLM R20+ PERFORMER 15/03/2010...
When displaying computer patterns or graphics (RGB or YUV signals) which are very detailed (tilting, vertical stripes, etc. ), jitter in picture (mis-sampling) may occur, causing horizontal stripes in portions of the screen. When this jitter occurs, adjust ’Phase’ for optimum image. Image 9-19 Jittering on image R5976921 FLM R20+ PERFORMER 15/03/2010...
4. Use the ▲ or ▼ key to select Sharpness and press ENTER. The Sharpness progress bar appears. 5. Use ◄ or ► to change the sharpness. The higher the value, the higher the sharpness. R5976921 FLM R20+ PERFORMER 15/03/2010...
4. Use the ▲ or ▼ key to select Noise reduction and press ENTER. The Noise reduction progress bar appears. 5. Use ◄ or ► to change the noise reduction. The higher the value, the higher the noise reduction. Image 9-29 Image 9-28 Image 9-30 Image 9-31 R5976921 FLM R20+ PERFORMER 15/03/2010...
5. Use the ▲ or ▼ key to select a predefined color temperature value, e.g. Video, and press ENTER. The colors of the image is switched to the selected value. Image 9-33 Image 9-32 Image 9-34 R5976921 FLM R20+ PERFORMER 15/03/2010...
6. Adjust gain red with ◄ or ► key and gain blue with ▲ or ▼ key. Adjust gain blue in the same way as gain red. 7. When gain adjustment is finished press ENTER. Image 9-37 Image 9-36 Image 9-38 Image 9-39 Image 9-40 R5976921 FLM R20+ PERFORMER 15/03/2010...
The graphic shows that when converting a signal containing a DC offset component the range of the converter is not optimally used. i2 : video information i1 : superfluous information Δ Black level Image 9-43 R5976921 FLM R20+ PERFORMER 15/03/2010...
Black balance : In the projector, we will set the brightness for each color until we get a 0% light output picture when projecting a 100% black image (image B). The changeover from min to max is indicated by the apparition of bright spots also called “digital noise” R5976921 FLM R20+ PERFORMER 15/03/2010...
11. Toggle with ▲ or ▼ key to Black balance blue adjust the Blue black level until bright spots appear on the screen. 12.Toggle with ▲ or ▼ key to Black balance red adjust the Red black level until bright spots appear on the screen. R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 85
12.Toggle with ▲ or ▼ key to White balance blue adjust the Blue white level (gain) until bright spots appear on the screen. 13.Toggle with ▲ or ▼ key to White balance red adjust the Red white level (gain) until bright spots appear on the screen. The projected image should now be noisy neutral gray. R5976921 FLM R20+ PERFORMER 15/03/2010...
Type of input signal is indicated above each image row. The image row shows how the image will be projected in the different aspect ratio settings. 16/9 Video Signal Pal/Secam Video Signal NTSC Video Signal 16/9 4/3 RGB Signal Image 9-56 Some examples for aspect ratio R5976921 FLM R20+ PERFORMER 15/03/2010...
Total pixels: Total horizontal pixels in the source. If the value is wrong, sampling mistakes (small vertical bars in the projected image) will be seen in the image. • Total lines: Total vertical lines in the source. R5976921 FLM R20+ PERFORMER 15/03/2010...
The time between the leading edge of the clamp pulse and the locked edge of the sync pulse. Can be any value between 0 and 255. Clamp width The width of the clamp pulse can be any value between 0 and 255. R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 89
5. Use the ▲ or ▼ key to select Clamp delay or Clamp width and press ENTER. A progress bar appears. 6. Use the ▲ or ▼ key to change the setting. Image 9-68 Image 9-67 Image 9-69 Image 9-70 R5976921 FLM R20+ PERFORMER 15/03/2010...
five video frames and four film frames, the latter identified as A-D. Only film frame A is fully on a video frame and so exists at one time code only, making it the editable point of the video sequence. R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 91
When film with a banner is projected at the same time, and film mode is auto, the banner will shown possible artefacts as the software will detect a film. Image 9-76 Image 9-75 Image 9-77 Image 9-78 R5976921 FLM R20+ PERFORMER 15/03/2010...
3. Use the ▲ or ▼ key to select File services and press ENTER. The File service menu is displayed. 4. Use the ▲ or ▼ key to select Manual load and press ENTER. The manual load window opens. Image 9-80 Image 9-81 Image 9-79 R5976921 FLM R20+ PERFORMER 15/03/2010...
5. Use the ▲ or ▼ key to select the file which must be deleted. Note: Only custom files can be deleted. 6. Press ENTER to delete the selected file. Image 9-84 Image 9-85 Image 9-83 R5976921 FLM R20+ PERFORMER 15/03/2010...
Image 9-90 if you are not sure to delete all custom files, select No and press ENTER to activate the selection. 9.6.5 Rename a file How to rename? 1. Press MENU to activate the menus. R5976921 FLM R20+ PERFORMER 15/03/2010...
Note: Digits can be entered with the digit keys on the remote control or on the local keypad. When a digit is entered in that way, the next character will be selected automatically. 8. Press ENTER to finalize the copy action. R5976921 FLM R20+ PERFORMER 15/03/2010...
4. Use the ▲ or ▼ key to select Options and press ENTER. Image 9-102 Image 9-103 Image 9-101 The options window opens. 5. Use the ▲ or ▼ key to select Load file and press ENTER to toggle between [Automatic], [Manual] and [Custom only]. R5976921 FLM R20+ PERFORMER 15/03/2010...
3. Use the ▲ or ▼ key to select Save custom settings and press ENTER. The custom settings are written to the internal backup device. A message menu “Save data ...” is displayed during the save operation. Image 9-108 Image 9-106 Image 9-107 R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 98
9. Image menu R5976921 FLM R20+ PERFORMER 15/03/2010...
When the active layout is a read only layout, the projector will ask to create a new layout. Use the ▲ or ▼ key to select Yes or No and press ENTER. If Yes is selected an Enter layout name window opens. R5976921 FLM R20+ PERFORMER 15/03/2010...
5. Use the ▲ or ▼ key to select the desired source and press ENTER to activate. Image 10-5 Image 10-4 Image 10-3 Image 10-6 10.2.2 Size adjustment What can be done? The size of the main window can be adjusted until the desired window dimensions are reached. R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 101
The main window opens. 4. Use the ▲ or ▼ key to select Size and press ENTER. The size adjustment window opens. Image 10-10 Image 10-9 Image 10-8 5. Toggle with ENTER till Lock is set to [x]. R5976921 FLM R20+ PERFORMER 15/03/2010...
4. Use the ▲ or ▼ key to select Size and press ENTER. The size adjustment window opens. Image 10-15 Image 10-14 Image 10-13 5. Toggle with ENTER till Lock is set to [ ]. R5976921 FLM R20+ PERFORMER 15/03/2010...
3. Use the ▲ or ▼ key to select Main Window and press ENTER. The main window opens. 4. Use the ▲ or ▼ key to select Position and press ENTER. The position adjustment window opens. 5. Use the ▲ or ▼ key to adjust top start point. R5976921 FLM R20+ PERFORMER 15/03/2010...
The input section of the projector allows a combinations of different input signals which may be projected in the 2 windows of the PiP screen. The PiP window can be placed anywhere, with any dimensions, on the screen by changing its position and its size. R5976921 FLM R20+ PERFORMER 15/03/2010...
2. Use the ▲ or ▼ key to select Window and press ENTER. 3. Use the ▲ or ▼ key to select PIP Window and press ENTER. The PIP window dialog opens. 4. Use the ▲ or ▼ key to select Source and press ENTER. R5976921 FLM R20+ PERFORMER 15/03/2010...
PIP window during a re-scaling. Due to the fact that the re-scale is done on the vertical dimensions of the PIP window and the image inside it will be re-scaled so that the aspect ratio is still correct. R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 107
[ ] = no lock between height and width. [x] = width and height are locked. 6. Use the ▲ ▼ or ◄ ►key to adjust the size with respect to the aspect ratio. When the desired size is reached, press EXIT. R5976921 FLM R20+ PERFORMER 15/03/2010...
[x] = width and height are locked. 6. Use the ▲ or ▼ key to adjust the height. Use the ◄ or ► key to adjust the width. When the desired size is reached, press EXIT. R5976921 FLM R20+ PERFORMER 15/03/2010...
Image 10-46 Image 10-44 Image 10-48 Image 10-47 6. Select with the ▲ or ▼ key Yes and press ENTER. Select with the ▲ or ▼ key No, when no save is desired and press ENTER. R5976921 FLM R20+ PERFORMER 15/03/2010...
The first 4 layouts are default layouts, all others are customer created layouts. The menu shows only the first 10 layouts, but use the ▼ to scroll through the rest of the layouts until the desired layout is found. Rigging key + sequence number opens directly the desired layout. R5976921 FLM R20+ PERFORMER 15/03/2010...
How to delete? 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Window and press ENTER. 3. Use the ▲ or ▼ key to select Layout services and press ENTER. R5976921 FLM R20+ PERFORMER 15/03/2010...
Note: Digits can be entered with the digit keys on the remote control or on the local keypad. When a digit is entered in that way, the next character is selected automatically. 7. Press ENTER to copy to the new name. The new layout will be added to the list of layouts. R5976921 FLM R20+ PERFORMER 15/03/2010...
[No] = each layout will use its own zoom/focus settings. [Yes] = each layout will use the same zoom/focus settings. That means that the zoom/focus settings of the previous selected layout will be applied to the next selected layouts. R5976921 FLM R20+ PERFORMER 15/03/2010...
2. Use the ▲ or ▼ key to select Lamp and press ENTER. 3. Use the ▲ or ▼ key to select Power and press ENTER. 4. Use the ▲ or ▼ key to select Mode. 5. Press ENTER to toggle between [Normal] and [Economic]. R5976921 FLM R20+ PERFORMER 15/03/2010...
3. Use the ▲ or ▼ key to select Power and press ENTER. 4. Use the ▲ or ▼ key to select Power and press ENTER. 5. Use the ▲ or ▼ key to change the lamp power. Image 11-5 Image 11-6 Image 11-4 Image 11-7 R5976921 FLM R20+ PERFORMER 15/03/2010...
2. Use the ▲ or ▼ key to select Lamp and press ENTER. 3. Use the ▲ or ▼ key to select Power and press ENTER. 4. Use the ▲ or ▼ key to select CLO mode and press ENTER to toggle between [On] and [Off] R5976921 FLM R20+ PERFORMER 15/03/2010...
Article number of the used lamp • Run time since first start up of the lamp • Remaining run time for a safe operation of the lamp • Number of strikes since the first start up of the lamp R5976921 FLM R20+ PERFORMER 15/03/2010...
2. Use the ▲ or ▼ key to select Lamp and press ENTER. 3. Use the ▲ or ▼ key to select Z-axis and press ENTER. The Z-axis dialog box is display and indicates the current light output.. Image 11-21 Image 11-20 Image 11-19 R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 120
11. Lamp menu R5976921 FLM R20+ PERFORMER 15/03/2010...
2. Use the ▲ or ▼ key to select Alignment and press ENTER. 3. Use the ▲ or ▼ key to select Orientation and press ENTER. 4. Use the ▲ or ▼ key to select the correct orientation and press ENTER. R5976921 FLM R20+ PERFORMER 15/03/2010...
3. Use the ▲ or ▼ key to select Lens and press ENTER. The lens adjustment menu is displayed. Image 12-6 Image 12-4 Image 12-5 Zoom/focus the lens 1. Use the ▲ or ▼ key to select Zoom/Focus and press ENTER. Image 12-8 Image 12-7 R5976921 FLM R20+ PERFORMER 15/03/2010...
The side keystone adjustment is used to align the image if the projector is mounted at a non standard projection angle. Image 12-12 Side keystone Keystone adjustment with positive values Keystone adjustment with negative values Side keystone adjustment 1. Press MENU to activate the menus. R5976921 FLM R20+ PERFORMER 15/03/2010...
While an image can be transformed in various ways, pure warping means that points are mapped to points without changing the colors. Some examples of projected images which need to be corrected with the warp geometry settings: R5976921 FLM R20+ PERFORMER 15/03/2010...
[Manual] : projector functions for warp are available. [File] : Sophisticated warp adjustments can be loaded via a file. The projector warp functions are not available. [Off] : No warp adjustments used in the projected image. Image 12-18 Image 12-19 Image 12-20 R5976921 FLM R20+ PERFORMER 15/03/2010...
The warp dialog box appears. 4. Use the ▲ or ▼ key to select Horizontal keystone and press ENTER. 5. Use ◄ or ► to change the horizontal keystone. Image 12-22 Image 12-23 Image 12-24 R5976921 FLM R20+ PERFORMER 15/03/2010...
3. Use the ▲ or ▼ key to select Warp and press ENTER. The warp dialog box appears. 4. Use the ▲ or ▼ key to select Vertical keystone and press ENTER. 5. Use ◄ or ► to change the vertical keystone. R5976921 FLM R20+ PERFORMER 15/03/2010...
3. Use the ▲ or ▼ key to select Warp and press ENTER. The warp dialog box appears. 4. Use the ▲ or ▼ key to select Rotation and press ENTER. 5. Use ◄ or ► to change the rotation angle. R5976921 FLM R20+ PERFORMER 15/03/2010...
3. Use the ▲ or ▼ key to select Warp and press ENTER. The warp dialog box appears. 4. Use the ▲ or ▼ key to select Pincushion/Barrel and press ENTER. 5. Use ◄ or ► to adjust the pincushion or the barrel distortion. R5976921 FLM R20+ PERFORMER 15/03/2010...
2. Use the ▲ or ▼ key to select Alignment and press ENTER. 3. Use the ▲ or ▼ key to select Warp and press ENTER. The warp dialog box appears. 4. Use the ▲ or ▼ key to select 4 corners and press ENTER. R5976921 FLM R20+ PERFORMER 15/03/2010...
3. Use the ▲ or ▼ key to select Warp and press ENTER. The warp dialog box appears. 4. Use the ▲ or ▼ key to select Reset and press ENTER. All warp settings are reset. The Status is set to [Off]. R5976921 FLM R20+ PERFORMER 15/03/2010...
The load file menu opens 5. Use the ▲ or ▼ key to select the desired file out of the list and press ENTER. The file is loaded and the corrections are applied. Image 12-51 Image 12-52 Image 12-53 R5976921 FLM R20+ PERFORMER 15/03/2010...
Blanking adjustments affect only the edges of the projected image and are used to frame the projected image on to the screen and to hide or black out unwanted information (or noise). A ’0’ on the bar scale indicates no blanking. R5976921 FLM R20+ PERFORMER 15/03/2010...
4. Use the ▲ or ▼ key to select the desired blanking adjustment and press ENTER. 5. Use the ▲ or ▼ key to adjust until the desired blanking is reached. 6. Press EXIT to return. Image 12-62 Image 12-60 Image 12-61 R5976921 FLM R20+ PERFORMER 15/03/2010...
4. Use the ▲ or ▼ key to scroll through the possible selection and press ENTER to activate the selected pattern. Select ▲ or ▼ in the menu to display the previous or next page with possible internal patterns. Image 12-68 Image 12-66 Image 12-67 R5976921 FLM R20+ PERFORMER 15/03/2010...
The user can define the x and y coordinates for red, green and blue which forms the corners of the color space. By changing the coordinates, the color reproduction can be changed. Image 12-71 Image 12-69 Image 12-70 R5976921 FLM R20+ PERFORMER 15/03/2010...
The principle of edge blending is achieved by linear modulation of the light output in the overlap zone so that the light output in that zone equals the light output of the rest of the image. R5976921 FLM R20+ PERFORMER 15/03/2010...
3. Use the ▲ or ▼ key to select ScenergiX and press ENTER. 4. Use the ▲ or ▼ key to select Status and press ENTER to toggle between [On] and [Off]. ScenergiX is active ScenergiX is not active Image 12-77 Image 12-75 Image 12-76 R5976921 FLM R20+ PERFORMER 15/03/2010...
1. Go to Layout → Main window → Size 2. Enter the value for the Width as follow: Total horizontal screen resolution / 2 - 0.5 x overlap zone. 3. Position remains the same. Image 12-81 Image 12-80 Image 12-79 Image 12-82 R5976921 FLM R20+ PERFORMER 15/03/2010...
Overlap : number of pixels that overlap Vertical resolution of 1 projector Total vertical screen resolution : [(Vertical resolution of 1 projector) x 2] minus (overlap) Vertical Resolution source : number of active lines of the source R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 142
2. Enter the value for the Width as follow: Total Vertical screen resolution / 2 - 0.5 x overlap zone. 3. Position = original start + Vertical height projector 1 - overlap zone Image 12-95 Image 12-94 Image 12-93 R5976921 FLM R20+ PERFORMER 15/03/2010...
4. Use the ▲ or ▼ key to select White level and press ENTER. 5. Use the ▲ or ▼ key to select one of the four size adjustments and press ENTER. Image 12-100 Image 12-98 Image 12-99 Image 12-101 R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 144
6. Use the cursor keys to move the border of the overlap area to the desired position. Set first the width for the first projector and repeat for the second one. Image 12-103 Width set up for projector 1 R5976921 FLM R20+ PERFORMER 15/03/2010...
2. Use the ▲ or ▼ key to select Alignment and press ENTER. 3. Use the ▲ or ▼ key to select ScenergiX and press ENTER. 4. Use the ▲ or ▼ key to select Black level and press ENTER. R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 146
5. Use the ▲ or ▼ key to select one of the four size adjustments and press ENTER. Image 12-108 Image 12-106 Image 12-107 Image 12-109 Image 12-110 DLP leakage area Overlap area DLP Leakage area 6. Use the cursor keys to move the green border line to the desired position. R5976921 FLM R20+ PERFORMER 15/03/2010...
5. Adjust the black level of area A until the black level of area A, B and C are equal. Use the Adjust function All, Red, Green and Blue in the Black level menu. Image 2 Image 1 Image 12-115 Black level adjustment Use the Reset function to bring all ScenergiX settings back to zero. R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 148
12. Alignment menu R5976921 FLM R20+ PERFORMER 15/03/2010...
DHCP [ON/OFF] IP-address Subnet mask Default gateway IR control IR Front [On/Off] IR Back [On/Off] IR Side [On/Off] ART DMX DMX address DMX universe DMX monitor DMX mode [Basic/Extended/Full] Home lens at startup [No/Yes] Buttons Standby R5976921 FLM R20+ PERFORMER 15/03/2010...
6. Use the ◄ or ► key to select the next digit and repeat step 5. 7. When the desired address is entered, press ENTER to store that address. R5976921 FLM R20+ PERFORMER 15/03/2010...
5. Use the ▲ or ▼ key to select ’0’ or ’1’ enter ’0’ or ’1’ with the digit keys on the remote control or local keypad. 6. When the desired address is entered, press ENTER to store that address. Image 13-7 Image 13-6 Image 13-5 R5976921 FLM R20+ PERFORMER 15/03/2010...
The communication protocol for the communication between the projector and a computer can be set to RS232 or RS422. How to set up 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Projector control and press ENTER. R5976921 FLM R20+ PERFORMER 15/03/2010...
4. Use the ▲ or ▼ key to select RS422 termination and press ENTER to toggle between [On] or [Off]. Default: [On] Image 13-17 Image 13-16 Image 13-15 13.4 Network Overview • Introduction to a Network connection • DHCP setup • IP-address set up • Subnet-mask set up • Default Gateway set up R5976921 FLM R20+ PERFORMER 15/03/2010...
3. Use the ▲ or ▼ key to select Ethernet and press ENTER. The Ethernet menu opens. 4. Use the ▲ or ▼ key to select DHCP. 5. Press ENTER to toggle the DHCP setting. R5976921 FLM R20+ PERFORMER 15/03/2010...
The next digit in the address will be selected automati- cally. 6. Press EXIT to return. Image 13-23 Image 13-22 Image 13-21 Image 13-24 13.4.4 Subnet-mask set up How to set up? 1. Press MENU to activate the menus. R5976921 FLM R20+ PERFORMER 15/03/2010...
5. Use the ▲ or ▼ key to select the desired digit and press ◄ or ► key to select the next digit in the address. enter the value with the digit keys on the remote control or local keypad. The next digit in the address will be selected automati- cally. Note: This must NOT be 0.0.0.0 R5976921 FLM R20+ PERFORMER 15/03/2010...
4. Use the ▲ or ▼ key to select the desired IR receiver and press ENTER to toggle this receiver [on] or [off]. Image 13-35 Image 13-34 Image 13-33 13.6 Art-Net DMX DMX-512 Lighting protocol, here used over Ethernet. Carries information of 512 channels from a lighting controller to lighting devices. Standardized by USITT. R5976921 FLM R20+ PERFORMER 15/03/2010...
13.6.2 DMX universe What can be done ? Depending on the DMX mode, one DMX universe can contain a different number of projectors. E.g. DMX mode = basis, the DMX universe can contain up to 256 projectors R5976921 FLM R20+ PERFORMER 15/03/2010...
4. Use the ▲ or ▼ key to select DMX monitor and press ENTER. The DMX monitor window opens. Depending on the DMX mode, a different view of the DMX monitor window opens. Example in dialog box is Extended mode R5976921 FLM R20+ PERFORMER 15/03/2010...
3. Use the ▲ or ▼ key to select ART DMX and press ENTER. 4. Use the ▲ or ▼ key to select DMX mode and press ENTER to toggle between [basic], [extended] or [full]. R5976921 FLM R20+ PERFORMER 15/03/2010...
3. Use the ▲ or ▼ key to select ART DMX and press ENTER. 4. Use the ▲ or ▼ key to select Home lens at startup and press ENTER to toggle between [On] or [Off]. R5976921 FLM R20+ PERFORMER 15/03/2010...
3. Use the ▲ or ▼ key to select Buttons and press ENTER. 4. Use the ▲ or ▼ key to select Standby and press ENTER to toggle between [Lamp on/off] and [Power up/down]. Image 13-59 Image 13-58 Image 13-57 R5976921 FLM R20+ PERFORMER 15/03/2010...
5. Use the ▲ or ▼ key to select a shortcut with allocation and press ENTER to remove the allocation. The indication becomes No allocation and the key is free again for a new shortcut association. Image 13-65 Image 13-64 Image 13-63 R5976921 FLM R20+ PERFORMER 15/03/2010...
3. Use the ▲ or ▼ key to select Menu position and press ENTER. 4. Use the ▲ or ▼ key to select Menu and press ENTER to toggle between [Center], [Top] and [Bottom]. Image 13-70 Image 13-69 Image 13-68 R5976921 FLM R20+ PERFORMER 15/03/2010...
3. Use the ▲ or ▼ key to select Local LCD and press ENTER. 4. Use the ▲ or ▼ key to select Local LCD time out and press ENTER to toggle between [Off], [5sec], [10sec] and [15sec]. R5976921 FLM R20+ PERFORMER 15/03/2010...
Image 13-79 Image 13-78 Image 13-81 13.10 Language selection What can be done? The user can change the language of the on screen menus and the local display menus to one of the available languages. R5976921 FLM R20+ PERFORMER 15/03/2010...
3. Use the ▲ or ▼ key to select Language and press ENTER. 4. Use the ▲ or ▼ key to select the desired language. The change will take effect immediately. Image 13-84 Image 13-83 Image 13-82 R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 168
13. Projector control R5976921 FLM R20+ PERFORMER 15/03/2010...
14. Service menu 14. SERVICE MENU About this chapter This chapter refers to the Service menu in which the customer can find valuable information when calling the Barco help desk. Overview • Overview flow • Identification • Diagnosis • Convergence •...
Use the ◄ or ► key to selected another character. Note: Digits can be entered with the digit keys on the remote control or on the local keypad. When a digit is entered in that way, the next character will be selected automatically. R5976921 FLM R20+ PERFORMER 15/03/2010...
3. Use the ▲ or ▼ key to select Diagnosis and press ENTER. The diagnosis screen is displayed. 4. Use the ▲ or ▼ key to select Versions and press ENTER. The Versions overview is displayed. Image 14-10 Image 14-8 Image 14-9 R5976921 FLM R20+ PERFORMER 15/03/2010...
3. Use the ▲ or ▼ key to select Diagnosis and press ENTER. The diagnosis screen will be displayed. 4. Use the ▲ or ▼ key to select Voltages and press ENTER. The Voltage overview menu will be displayed. Image 14-14 Image 14-12 Image 14-13 Image 14-15 R5976921 FLM R20+ PERFORMER 15/03/2010...
The service window opens. 3. Use the ▲ or ▼ key to select Diagnosis and press ENTER. The diagnosis screen will be displayed. 4. Use the ▲ or ▼ key to select Temperatures and press ENTER. R5976921 FLM R20+ PERFORMER 15/03/2010...
3. Use the ▲ or ▼ key to select Diagnosis and press ENTER. The diagnosis screen will be displayed. 4. Use the ▲ or ▼ key to select Fan speeds and press ENTER. The Fan speeds overview menu will be displayed. R5976921 FLM R20+ PERFORMER 15/03/2010...
3. Use the ▲ or ▼ key to select Diagnosis and press ENTER. The diagnosis screen will be displayed. 4. Use the ▲ or ▼ key to select SPI and press ENTER. The SPI overview menu will be displayed. Image 14-30 Image 14-28 Image 14-29 R5976921 FLM R20+ PERFORMER 15/03/2010...
2. Use the ▲ or ▼ key to select Service and press ENTER. The service window opens. 3. Use the ▲ or ▼ key to select Convergence and press ENTER. 4. Use the ▲ or ▼ key to select the desired pattern and press ENTER. R5976921 FLM R20+ PERFORMER 15/03/2010...
1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Service and press ENTER. The service window opens. 3. Use the ▲ or ▼ key to select Internal service patterns and press ENTER. R5976921 FLM R20+ PERFORMER 15/03/2010...
4. Use the ▲ or ▼ key to select the setting to exclude and press ENTER to toggle between [No] and [Yes]. Repeat this step if necessary for the other settings. Image 14-43 Image 14-44 Image 14-45 R5976921 FLM R20+ PERFORMER 15/03/2010...
4. Use the ▲ or ▼ key to select Yes or No and press ENTER. If you want to reset the formatter, select Yes. If you do not want to reset the formatter, select No. Image 14-51 Image 14-49 Image 14-50 R5976921 FLM R20+ PERFORMER 15/03/2010...
3. Use the ▲ or ▼ key to select Refill mode and press ENTER. A refill confirmation message is displayed. 4. Use the ▲ or ▼ key to select Yes or No and press ENTER. R5976921 FLM R20+ PERFORMER 15/03/2010...
2. Use the ▲ or ▼ key to select Service and press ENTER. The service window opens. 3. Use the ▲ or ▼ key to select Broadcast mode and press ENTER to toggle between [Off] and [On]. Image 14-57 Image 14-58 R5976921 FLM R20+ PERFORMER 15/03/2010...
3. Use the ▲ or ▼ key to select Service and press ENTER. The service window opens. 4. Use the ▲ or ▼ key to select USB memory and press ENTER. 5. Use the ▲ or ▼ key to select Save custom settings and press ENTER. R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 183
6. Use the ▲ or ▼ key to select the serial number to start from to load the settings. The settings from the selected projector on the USB device are loaded into the current attached projector. The current projector settings are overwritten with these settings. Image 14-64 Image 14-62 Image 14-63 Image 14-65 R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 184
14. Service menu R5976921 FLM R20+ PERFORMER 15/03/2010...
Make sure that the airflow indicated on the dust filter match with the airflow of the fans. 4. Reinstall the front cover of the projector, see "Installation of the front cover", page 196. 1. High Efficiency Particulate Arrestant R5976921 FLM R20+ PERFORMER 15/03/2010...
Make sure that the airflow indicated on the dust filter match with the airflow of the fans. 5. Reinstall the filter holder containing the new HEPA filter. 6. Fasten the two wedge lock screws (A) using a 2.5 mm Allen key as illustrated. R5976921 FLM R20+ PERFORMER 15/03/2010...
15.4 Pressure verification of the liquid cooling circuit How to check the pressure of the liquid cooling circuit inside the projector ? 1. Remove the side cover of the projector, see "Removal of the side cover", page 194. R5976921 FLM R20+ PERFORMER 15/03/2010...
1. Switch off the projector and unplug the power cord at the projector side. 2. Clean the housing of the projector with a damp cloth. Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution. R5976921 FLM R20+ PERFORMER 15/03/2010...
ARNING AUTION Never attempt to disassemble the lamp from its housing or to dispose of it. Return it to Barco. Due to its high internal pressure, the lamp may explode in either hot or cold states if improperly handled. Necessary tools 7 mm flat screw driver.
4. Release the four captive screws in the corners of the input and communication unit as illustrated. Image 16-3 5. Pull the input & communication unit out of its compartment, using the side handles provided. R5976921 FLM R20+ PERFORMER 15/03/2010...
2. Release the two captive screws of the input module using a Phillips screw driver PH1. Image 16-5 3. Pull the input module out of the input & communication unit, via the two knobs provided. R5976921 FLM R20+ PERFORMER 15/03/2010...
This procedure may only be performed by qualified technical service personnel. AUTION Never attempt to disassemble the lamp from its housing or to dispose of it. Return it to Barco. Due to its high internal pressure, the lamp may explode in either hot or cold states if improperly handled.
2. Remove the input cover, if not removed yet. See "Removal of the input cover", page 195. 3. Hold the input & communication unit by its handles and gently slide the unit into the guides at the bottom of the input & commu- nication socket inside the projector. R5976921 FLM R20+ PERFORMER 15/03/2010...
How to install an input module into the input & communication unit of the projector ? 1. Switch off the projector and unplug the power cord at the projector side. 2. Slide the input module into the guides of the input slot. R5976921 FLM R20+ PERFORMER 15/03/2010...
3. Start up the projector, enter the menu structure and select Lamp / Z-axis (for more explanation, see "Z-axis adjustment", page 115) 4. Carefully turn the thumb screw (A) at the rear of the lamp house clockwise for maximum light output. Once over the maximum, turn slightly counterclockwise to reach the maximum light output again. R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 196
16. Servicing Image 16-13 5. Switch off the projector, wait five minutes and unplug the power cord at the projector side. 6. Reinstall the cover of the lamp, see "Installation of the lamp cover", page 198. R5976921 FLM R20+ PERFORMER 15/03/2010...
(A) of the side cover, b) then gently pull out the top corners (B) of the side cover, c) then move the side cover away from the projector (C). Image 17-4 R5976921 FLM R20+ PERFORMER 15/03/2010...
7 mm flat screw driver. How to remove the input cover of the projector ? 1. Release the two captive screws at the top and bottom left side of the input cover, using a flat screw driver. R5976921 FLM R20+ PERFORMER 15/03/2010...
first hook in the side of the front cover at the front filter, b) then gently push the other side of the front cover into position, c) ensure that the locking studs in the corners click into their receivers. R5976921 FLM R20+ PERFORMER 15/03/2010...
Bring the side cover towards its final position (A), b) then gently push the locking studs of the top corners (B) into their receivers, c) then gently push the locking studs of the bottom corners (C) into their receivers. R5976921 FLM R20+ PERFORMER 15/03/2010...
(C) into its receiver. Image 17-14 2. Secure the lamp cover by locking the two captive screws at the right side of the lamp cover. Image 17-15 R5976921 FLM R20+ PERFORMER 15/03/2010...
(C) into its receiver. Image 17-16 2. Secure the input cover by locking the two captive screws at the left side of the input cover. R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 204
17. Removal of the projector covers R5976921 FLM R20+ PERFORMER 15/03/2010...
Overview • Dimensions of the FLM R20+ Performer • Dimensions of the FLM flight case • Dimensions of the rigging clamps A.1 Dimensions of the FLM R20+ Performer Dimensions 14.8 676.1 771.1 Image A-1 Dimensions given in millimeters. R5976921 FLM R20+ PERFORMER 15/03/2010...
A. Dimensions Point of gravity Image A-2 Dimensions given in millimeters. A.2 Dimensions of the FLM flight case Dimensions 1194 1175 Image A-3 Dimensions given in millimeters. R5976921 FLM R20+ PERFORMER 15/03/2010...
A. Dimensions A.3 Dimensions of the rigging clamps Dimensions SW17 26.5 Image A-4 Dimensions given in millimeters. R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 208
A. Dimensions R5976921 FLM R20+ PERFORMER 15/03/2010...
5. Fpix MHz: pixel frequency 6. Ptot : total pixels on one horizontal line. 7. Pact: active pixels on one horizontal line. 8. Ltot: total lines in one field 9. Lact: active lines in one field. R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 218
Light pipe temp Temperature sensor on light pipe Call a qualified service engineer short shorted 7695 Low temperature on red DMD Red front DMD Switching on the lamp will heat up temp low the DMD R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 219
Green block Temperature sensor on green DMD Call a qualified service engineer temp open cooling block not connected 7666 Green block Temperature sensor on green DMD Call a qualified service engineer temp short cooling block shorted R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 220
filters If problem persists, call a qualified service engineer 7981 Blue DMD low temperature on dmd turning on the lamp will heat up the temp low R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 221
7956 30V voltage supply voltage for fans too high If problem persists, call a qualified high service engineer 7955 VTEC voltage supply voltage for DMD cooling too If problem persists, call a qualified service engineer R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 222
EEPROM service engineer 9000 Scaler unit Initialization of the scaler failed If problem persists, call a qualified failed service engineer 9198 Scaler pixel BW or refresh rate of input source clock too high too high R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 223
Description Error Warning Action Caused by code 9398 Maximum Reaching the maximum allowed Delete some unnecessary files image files number of files reached 10498 Unsupported Module with obsolete firmware Call a qualified service engineer module R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 224
D. Troubleshooting R5976921 FLM R20+ PERFORMER 15/03/2010...
— Component Video / (R - Y) / (B - Y) - SOY Specifications • Data and HD sources RGB and YUV [HS/VS, CS or SOG(Y)]: Pixel clock maximum 275 MHz 8 bit digital output R5976921 FLM R20+ PERFORMER 15/03/2010...
Diagnostic LED’s on front panel: Green LED: Lights up in case input module is selected Yellow LED: Lights up in case sync detected • SDI: 270 Mbit/s transmission (SMPTE 259M-C). • SDI: 525/625 interlaced. • Coax (75 Ohm). R5976921 FLM R20+ PERFORMER 15/03/2010...
Cable lengths: up to 3 meter at UXGA speed. • Compliance: DDC2B support according to VESA EDID Version 1.2 • Diagnostic LED’s on front panel: Green LED: Lights up in case input module is selected Yellow LED: Lights up in case sync detected R5976921 FLM R20+ PERFORMER 15/03/2010...
Cable lengths: up to 3 meter at UXGA speed. • Compliance: DDC2B support according to VESA EDID Version 1.2 • Diagnostic LED’s on front panel: Green LED: Lights up in case input module is selected Yellow LED: Lights up in case sync detected R5976921 FLM R20+ PERFORMER 15/03/2010...
Thus, unlike “Brightness” and “Contrast” controls, the overall tone of your images can be lightened or darkened without changing the extremes, and all images will be more vibrant while still showing good detail in dark areas. R5976921 FLM R20+ PERFORMER 15/03/2010...
Page 234
2 lines is < - 0.2V that equals with a logical ’0’. When the difference is > +0.2V that equals to a logical ’1’.. Subnet mask A number that is used to identify a subnetwork so that IP addresses can be shared on a local area network. R5976921 FLM R20+ PERFORMER 15/03/2010...