Page 2
28 South 1550 West quality without adequate disinfection Lindon UT 84042-1617 before or after the system. (801) 785-5557 pn: LBL-HB-48-CERT See pages 8 through 11 for: • pre-installation checklist • installation instructions • start-up directions 2 | Hamilton Beach Owner’s Manual...
Equipment Specifications Your Hamilton Beach owner’s manual is designed to Working Pressure ......20 psi to 120 psi assist owners and installers with the installation, operation, Voltage .
Total family daily usage: gallons Total family daily usage: _________ gallons Hardness: x 20 grains per gallon Hardness: x _________ grains per gallon Total removal per day: 8,400 grains Total removal per day: _________ grains Hamilton Beach Owner’s Manual | 5...
“Back to Back” regenerations. This can be done easily by pressing the [REGEN] button one time, waiting at least one minute and pressing the [REGEN] button again. Measurements : Your Hamilton Beach water system registers ------------------------------------------------------------------------------------- hardness in grains per gallon (gpg). Most water analysis reports...
SA-HB-40-DB-CERT ..1.5 Fluid ounces SA-HB-48-DB-CERT ..1.8 Fluid ounces Hamilton Beach Systems use a dry brine tank. Since the system determines the amount of solution necessary to regenerate Add the sodium hypochlorite solution to the brine well of the the exhausted resin, water is sent to the brine tank as part of brine tank.
Manual Bypass Valve (Optional) Do not use soft vinyl tubing, 3/8” or smaller Your Hamilton Beach system is equipped with a manual tubing. Do not expose tubing to freezing. bypass valve. (See Figure 4.) This valve is to be used if you...
• Use caution if soldering inlet, outlet, or drain lines. 61–120 psi AVP-1032977 (#4 Injector) Excess heat will damage the control valve and/or (420–827 bar) bypass valve. Table 2: Injector selection based on water pressure. Hamilton Beach Owner’s Manual | 9...
Figure 10 3. Slowly open the inlet valve (only) on the bypass valve allowing the system to pressurize. It is normal to hear air blowing to the drain during this procedure. Figure 12 10 | Hamilton Beach Owner’s Manual...
Page 11
6. After the ten-minute refill time, manually advance the control valve to the service position. (See Neither splice connections nor extension wire Figure 14.) are supplied. They are available at hardware or electrical stores. Figure 16 (AVP-1000907) Figure 14 Figure 17 Hamilton Beach Owner’s Manual | 11...
Programming the Control Battery Backup Feature Valve Your Hamilton Beach softening system has a battery backup feature that allows the control to continue monitoring water flow and maintain the proper time of day during short power You are now ready to continue programming the control.
Ranges: 0.1 to 140 Kgr or 0.01 to 14.0 Kgr Figure 19: Control valve interface. Minimum Increments: 0.1 Kgr or 0.01 Kgr Units of Measure: Kgr or Kilograms Range: Depends on value selected for P12 Hamilton Beach Owner’s Manual | 13...
Page 14
It is recommended that a water test be performed [ ! ] button will return you to the far right digit. at the time of installation. This Hamilton Beach is designed to run on one water source. If multiple water sources are used, it...
1 = salt / capacity change locked out Skip this parameter to accept the default (no lock out) Factory defaults DO NOT Loads in factory default values. DO NOT CHANGE THIS CHANGE PARAMETER. Table 6: Level II programming parameters. Hamilton Beach Owner’s Manual | 15...
Units of measure Clock mode Calendar override Reserve type Fixed reserve capacity or initial average value Operation type Salt / capacity change lock out Factory defaults Table 7: Level I and II programming default settings. 16 | Hamilton Beach Owner’s Manual...
48.0 Table 8: System capacity by pounds of salt. SA-HB-40-DB-CERT certified capacity at salt setting SA-HB-48-DB-CERT certified capacity at salt setting Note: The 3.0 lbs salt setting (40 DB model) and the 3.6 lbs salt setting (48 DB model) are certified using the 5 bump injector. The 7.5 lbs (40 DB), 15 lbs (40 DB), 9 lbs (48 DB), and 18 lbs (48 DB) are certified using the 4 bump injector.
Control Valve Diagram Control Valve Diagram 20 | Hamilton Beach Owner’s Manual...
Page 21
Top Plate Assembly with Springs AVP-1032416 Air Check Kit AVP-1032250 Drive Gear AVP-1006002 Screw, 8-18 x 1-1/2 inch AVP-1031118 Spring AVP-1006093 Top Plate Screw AVP-1033998 Black Cover Not Used — — AVP-1000811 Transformer, 120V AVP-1000906 Micro Switch Hamilton Beach Owner’s Manual | 21...
Errors The control valve may be manually indexed to each regeneration position as follows: The Hamilton Beach System continuously monitors itself and displays an error message if it detects something wrong. 1. Remove the control valve cover. 2. Press down on the top of the drive gear to When an error is detected, the display shows the letters “Err”...
Page 24
Connect power when [REGEN] button is depressed No electric power at outlet Repair outlet or use working outlet Defective motor Replace motor assembly Defective switch Replace switch Table 10: Troubleshooting procedures for most common problems. 24 | Hamilton Beach Owner’s Manual...
Page 25
Incorrect salt type or use of grid plate (salt shelf) Do not use block salt or grid plate (salt shelf) in brine tank in brine tank Table 10:(Contiuned) Troubleshooting procedures for most common Hamilton Beach Owner’s Manual | 25...
Page 26
Incorrect salt type or use of grid plate (salt shelf) Do not use block salt or grid plate (salt shelf) in in brine tank brine tank Table 10:(Continued) Troubleshooting procedures for most common problems. 26 | Hamilton Beach Owner’s Manual...