Panasonic TH-50PB2W Operating Instructions Manual page 52

Options Adjustments
Item
Off: Nullify all the settings adjusted.
On: Sets the colour temperature for TV studio.
Studio W/B
Note: Valid only when the "Warm" is set as "White balance" in Picture menu.
Sharpens the contrast for a better view when a part of the image is too light to see.
Off: Disables "Studio Gain".
On: Enables "Studio Gain".
Studio Gain
Note: This setting is valid only when the input signals are as follows:
Off
Off:
Auto: Power is transmitted to the slot power only when main power is on.
Slot power
On:
Note: In some cases, power is transmitted to the slot power when main power is on or in the standby
Off
You can set the power-on delay time of the displays to reduce the power load, when you press
turn on the multiple displays that are set together.
Set each display's setting individually.
Off:
1 to 30 (sec.): Set the power-on delay time (second).
Power On Screen
Notes:
Delay
• During this function is working, the power indicator is blinking green.
• This function also works when the power recovers from failure or after plugging off and in again the
power cord.
After you unplug and plug the power cord in while the unit is in standby mode and also the power is
being supplied to a terminal board, the unit will start supplying the power to the board with time delay
according to the setting.
The power indicator lights up red fi rst and it turns orange when the power starts being supplied to the
board.
Off: Not display the clock.
On: Display the clock.
The clock is displayed at the lower left of the screen when
Clock Display
Sets All Aspect mode (advanced aspect setting) or default aspect mode.
With each press of
Off: Default aspect mode
On: All Aspect mode
All Aspect
Aspect mode of each setting is as follows:
(Example: HD signal)
Off 4:3→4:3 Full→Zoom1→Zoom2→Zoom3→16:9→14:9→Just
On 4:3 (1)→4:3 (2)→4:3 Full→Zoom1→Zoom2→Zoom3→16:9→14:9→Just1→Just2
Sets the operational mode of the automatic position adjustment in the Pos./Size menu.
Manual: Automatic position adjustment starts when
Auto Setup
Auto:
Off: Does not rotate the image.
Rotate
On: Rotates the image 180 degrees.
Whether to show/hide No activity power off Precautions at the time of power ON is set.
Power On Message
On: The warning precautions are shown at the time of power ON.
(No activity power
Off: The warning precautions are not shown at the time of power ON.
off)
Note: This setting is enabled only if "No activity power off" is "Enable" (see page 45).
Whether to show/hide an information message that tells the power has been turned off by Power
Management when the power is set to ON.
On: The information is shown at the time of power ON.
Power On Message
Off: The information is not shown at the time of power ON.
(Power Management)
Note: This setting is enabled only if "PC Power management" or "DVI-D Power management" is "On"
52
Component Video, RGB (analog), SDI, HDMI
Auto On
Power is not transmitted to the slot power.
Power is transmitted to the slot power when main power is on or in the standby state.
state regardless of the slot power setting.
1 2 3.... 30
The display will be turned on at the same time as
After pressing , the display will be powered on with time delay depending on this
setting.
Note: When "Day/Time Setup" is not set, the clock is not displayed even if "Clock
Display" is "On". (see page 33)
10:00
button, the aspect changes in the selected mode.
position adjustment is executed from the Pos./Size menu.
Other than remote control or menu operation, automatic position adjustment starts:
When the display power is turned ON.
When the input signal is switched.
(see page 42).
Adjustments
is pressed.
button is pressed.
is pressed on the remote control or automatic
to