Burner Adjustments - Lennox Hearth Products EBSTNM-2 Homeowner's Care And Operation Instructions Manual

B-vent multi-open elite series

Hide thumbs

Table Of Contents

Table of Contents

Enlarged version

WARNING: DO NOT ATTEMPT TO SUBSTI-

TUTE THE MATERIALS USED ON THESE

DOORS, OR REPLACE CRACKED OR BRO-

KEN GLASS WITH ANY MATERIALS OTHER

THAN THOSE PROVIDED BY THE APPLI-

ANCE MANUFACTURER.

THE GLASS DOORS OF THIS APPLIANCE MUST

ONLY BE REPLACED AS A COMPLETE UNIT AS

PROVIDED BY THE MANUFACTURER. DO

NOT ATTEMPT TO REPLACE BROKEN,

CRACKED OR CHIPPED GLASS SEPARATELY.

Refer to Figure 6 and remove the front glass

enclosure panel as follows:

1. Remove the top bustle, and the top louver

assembly or radiant panel. Then remove the

bottom bustle.

2. Open the control compartment access panel.

To open the control compartment access panel,

actuate the spring-loaded magnetic catches

securing the panel, by gently depressing the

outer top corners of the panel until the catches

"pop" the door free, allowing it to swing out and

down to open.

3. Remove the bottom control compartment

access panel by compressing the spring-loaded

hinge pin on the left side until it disengages

from the left cabinet corner post hole. Pull the

panel away from the fireplace.

4. Once the control compartment access panel

has been removed, the modesty panel can be

removed as follows: pull the bottom right

corner of the modesty panel out slightly to

disengage the snap-fit feature; lift the modesty

panel by the tab on the panel's right end, pull

the right end of the panel away from the

cabinet and then pull the panel diagonally out

of the left side cabinet panel slots. (In the

above procedure, reverse the words "left" and

"right" for EBCR-2 models).

Remove the modesty panel carefully, so that

none of the wires become loose or discon-

nected. Now complete access to the gas control

valve and its related controls is attainable.

Lower Compartment Door and Hinge

Top Flange

Modesty Panel

(Glass Enclosure

Panel Frame)

Glass

Enclosure

Panel

Latch

Bottom Vee-flange

(Glass Enclosure

Firebox Floor

Panel Frame)

EBST-2 SHOWN

Figure 6

5. Locate the latch at the top of the control

compartment. To disengage the latch from the

bottom vee-flange of the glass enclosure panel,

reach for the handle located towards the back

of the latch and pull the handle down towards

the front of the unit.

6. Swing the bottom of the door out and raise

it slightly to lift the top flange of the door frame

away from the appliance.

To install the front glass enclosure panel,

proceed as follows:

1. Visually inspect the gasket on the backside

of the panel. The gasket surface must be clean,

free of irregularities and seated firmly.

2. Position the glass enclosure panel in front

of the firebox opening at a 45 degree angle and

engage the top flange over the lip at the top of

the firebox opening.

3. Swing the glass enclosure panel down and

back. Ensure the gasket seats evenly as the

panel draws shut. Engage the Vee-flange at

the bottom of the panel with the latch and then

close the latch to secure the panel.

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

4. Reinstall the modesty panel by inserting the

tongues on the left side of it into the slots on

the left side cabinet panel. Swing the right side

of the modesty panel towards the unit. Engage

Front Glass

the hook on the right side of the modesty panel

Enclosure Panel

with the right side cabinet panel slot. Gently

press the bottom right corner of the modesty

panel to engage the snap-fit feature.

(The left and right designations used here are

reversed in EBCR-2 applications.)

5. Reinstall the bottom control compartment

access panel by inserting the right side locat-

ing pin into the right side cabinet panel and

then the left side spring-loaded pin into the left

side cabinet panel.

6. Reinstall the top and bottom bustle, and the

top louver assembly or radiant panel.