Remote Control; Placing The Television In Standby Mode - Samsung CS29Z45Z39 Owner's Instructions Manual

Remote Control

(depending on the model)
➢
Operation of remote control may be affected by bright
artificial light near to the TV.
MUTE
LNA
1 1 POWER 3 3 -/--
Used to switch the TV Used to select a channel
on and off. numbered ten or over.
Press this button, then
2 2 Numeric buttons
"--" symbol is
Used to select channels
displayed. Enter the
directly.
two-digit channel
number.
$ $ EXIT
4 4
/
Used to increase or Used to exit from any
display or return to
decrease the volume.
normal viewing.
5 5 MENU
% % MUTE
Used to display the on-
screen menu or return to Used to switch the
sound off temporarily. To
the previous menu.
turn the sound back on,
LNA
press the MUTE,
6 6 ... ... / † † / œ œ / √ √
button.
Used to control the
^ ^ ENTER
cursor in the menu.
While using the on-
7 7 S.MENU
screen menus, press the
Used to display the
ENTER button to
sound menu.
activate (or change) a
8 8 TURBO
particular item.
Used to select the turbo
& & S.MODE
sound option.
Used to select the
9 9 DUAL I-II
sound effect.
Used to select the
* * P.MODE
sound mode.
Used to select the
0 0 SOURCE picture effect.
Used to display all of the
( ( TV
available video sources.
Used to return to the TV
! ! INFO
mode when it is in
external input mode.
Used to view the
channel information and
) ) EZ.VIEW
setting status you
Used to make TV
selected.
viewing much easier.
@ @ PRE-CH
Used to switch
repeatedly between the
last two channels
displayed.
# # CH
/
Used to display the next
or previous stored
channel.
Installing Batteries
Remove the cover. Install two AAA
size batteries, then replace the cover.
When the remote control does not
operate normally, check that the "+"
and "-" ends of the batteries are inserted correctly or the
batteries are drained.
➢
Do not mix battery types, i.e. alkaline and manganese.
English - 3
Switching the Television On and Off
The mains lead is attached to the rear of the television.
1 Plug the mains lead into an appropriate socket.
➢
The main voltage is indicated on the rear of the
television and the frequency is 50 or 60Hz.
2 Press the "I" button (On/Off) on the front (or side) of the
, or
television.
3 Press the POWER button on the remote control to
switch the television on. The programme that you were
watching last is re-selected automatically. If you have
not yet stored any channels, no clear picture appears.
Refer to "Channel - Auto Store" on page 3 or "Channel -
Manual Store" on page 4.
➢
If the television is initially powered on, several basic
customer settings proceed automatically. Refer to
"Setup - Plug & Play" on page 3.
4 To switch the television off, press the "I" button (On/Off)
on the front (or side) of the television.

Placing the Television in Standby Mode

The television can be placed in standby mode, in order to
reduce power consumption and wear of the cathode ray
tube. Standby mode can be useful when you wish to
interrupt viewing temporarily (during a meal, for example).
1 Press the POWER button on the remote control while
viewing.
The television is in standby mode.
2 To switch the television back on, simply press it again.
☛
Do not leave the television in standby mode for long
periods of time (when you are away on holiday, for
example). Turn the television off by pressing the "I"
button (On/Off) on the front (or side) of the television. It
is best to unplug the set from the mains and aerial.