Brother DCP-J125 Quick Setup Manual

Unpack the machine and check the components
1
Start Here
WARNING indicates a
potentially hazardous
WARNING
situation which, if not
avoided, could result in
a.
death or serious injuries.
b.
c.
c.
Press and slide the
paper side guides
a and paper length
guide b to fit the
paper size.
3
Make sure that the
triangular marks c
on the paper side
guides a and paper
length guide b line
up with the mark for
the paper size you
are using.
3
Install the ink cartridges
4
a. c.
The LCD shows Remove the green protective
part a.
No Ink Cartridge.
b.
Open the ink cartridge
cover a.
Note
1
Do not throw away the green
protective part. You will need it
if you transport the machine.
Choose your language (if needed)
6
a.
Press Menu.
b.
Press a or b to choose Initial Setup.
Press OK.
c.
Press a or b to choose Local Language.
Press OK.
d.
Press a or b to choose your language.
Press OK.
e.
Press Stop/Exit.
Before you can use the machine, read this Quick Setup Guide
for the correct setup and installation.
LX7175001
USA/CAN
Printed in China
Note
• The components of your box may differ depending on your country.
• Save all packing materials and the box in case for any reason you must ship your machine.
• A USB cable is not included.
Please make sure you use a USB 2.0 cable (Type A/B) that is no more than 6 feet (2 meters) long
(cable not included).
Your machine has a USB interface that is compatible with the USB 2.0 specifi cation. This interface is
also compatible with Hi-Speed USB 2.0; however, the maximum data transfer rate will be 12 Mbits/s.
The machine can also be connected to a computer that has a USB 1.1 interface.
Remove the protective tape and film covering the machine, and also from the LCD.
Remove the plastic bag a containing the ink cartridges from on top of the paper tray.
Make sure you have all components.
d.
Fan the stack
Note
of paper well.
1
When you use Legal size paper, press and
hold the universal guide release button
e.
Gently put the
as you slide out the front of the paper tray.
paper into the
paper tray.
Check that the
paper is flat in
2
the tray.
IMPORTANT
DO NOT push the paper in too far.
d.
Unpack the ink cartridge.
Turn the green knob on the protective yellow cap clockwise until
it clicks to release the vacuum seal, then remove the cap a.
1
Note
Make sure you install the Starter
Ink Cartridges included with
your machine fi rst.
1
Set the LCD contrast (if needed)
7
a.
Press Menu.
b.
Press a or b to choose
General Setup, and then press OK.
c.
Press a or b to choose
LCD Settings, and press OK.
d.
Press a or b to choose
LCD Contrast, and then press OK.
e.
Press d or c to choose the contrast level,
and then press OK.
f.
Press Stop/Exit.
1
Accessory Order Form

Quick Setup Guide

Safety and Legal booklet
WARNING
Plastic bags are used in the packaging of your machine. To avoid danger of
suffocation, please keep these bags away from babies and children.
f. g.
Gently adjust the paper
side guides to the
paper with both hands.
a
Make sure the paper
side guides touch the
edges of the paper.
1
e. f.
Install each ink cartridge in Gently push the ink cartridge until it clicks. After all
the direction of the arrow on the ink cartridges are installed close the ink cartridge
the label. cover.
Take care to match the
color of the lever a with the
cartridge color b.
1
2
Set the date and time
8
a. d.
Press Menu. To enter the last two digits of the year, press a, b, d or
c to select a number and press OK. To save the year,
b.
Press a or b to choose press a, b, d or c to select
Initial Setup, and then press OK.
c.
Press a or b to choose
Date&Time, and then press OK.
Load plain Letter/A4 paper
2
a.
Pull out the paper tray.
Starter Ink Cartridges [x4]
Black
Yellow
Cyan
Magenta
Installation CD-ROM
Documentation CD-ROM
Basic User's Guide
Product Registration
Sheet (USA only)
h.
Close the output paper tray cover Pull out the paper support a
and slowly push the paper tray until it clicks, and then unfold
the paper support flap b.
back into the machine.
2
1
Check the print quality
5
a.
When the
preparation process
has finished, the
LCD shows
Set Paper and
Note
Press Start.
The machine will
Press Color Start.
prepare the ink
tube system for
printing.
This process will
take approximately
four minutes.
Do not turn off the
machine.
e.
Repeat for Month and Day.
f.
Press a or b to choose 12h Clock or 24h Clock,
and press OK.
OK OK
and then press OK.
Year:2010
g.
Enter the time, and then press OK.
1 2 3
h.
(12h Clock only)
4 5 6
Press a or b to choose AM or PM, and then press OK.
7 8 9
i.
Press Stop/Exit.
0 OK OK
(e.g. Enter 10 for 2010.)
Note
If you make a mistake and want to start again,
press Stop/Exit to go back to step a.
Quick Setup Guide
DCP-J125
b.
Lift the output paper tray cover a.
1
Connect the power cord
3
a.
Connect the power cord.
IMPORTANT
DO NOT connect the
USB cable yet.
Note
The Warning LED
on the control panel
will stay on until you
have installed the
ink cartridges.
b.
Check the quality of the four color blocks a
on the sheet.
(black/yellow/cyan/magenta)
1
OK
If all lines are clear and visible,
o
press (Yes) to finish the quality
check.
Poor
If you can see missing short lines,
o
press (No) and follow the steps
on the LCD.
Turn the sheet over.