TABLE OF CONTENTS TOPICS PAGE INTRODUCTION ------------------------------------------ SAFETY PRECAUTIONS ------------------------------------ CHARACTERISTICS OF NB-1900N ---------------------------- SPECIFICATIONS ----------------------------------------- SETUP ------------------------------------------------ NAME OF MAJOR PARTS OF MACHINE ------------------------ INSTRUCTION OF CONTROL PANEL AND DISPLAY ---------------- 1.FUNCTION OF BUTTONS ------------------------------- 2.DISPLAY ------------------------------------------- 3.INSTRUCTION BOTTONS AND LED ------------------------ LAMINATING STEPS -------------------------------------- 1.HOT LAMINATING ------------------------------------...
INTRODUCTION Thank you for purchasing a Royal Sovereign Laminator. To insure high quality lamination, please read this instroduction manual thoroughly. For additional product support or factory-direct ordering information. Call Royal Sovereign Customer Service at (800) 397-1025. SAFETY PRECAUTIONS The safety recommendations outlined in this section are to be read, understood and followed before operating the machine.
CHARACTERISTICS OF LAMINATOR NB-1900N LAMINATOR NB-1900N is an advanced laminator of contemporary design, utilizing the lastest in laminating technology. 1. Contemporary design and rounded shape will enhance any decor. 2. A microprocessor is used for added protection. 1) The microprocessor protects the rollers ①Even when power is off, rollers continue to turn until properly cooled down.
SPECIFICATIONS Description NB - 1900N Dimensions(w x d x h) 680x225x127mm (26.8"x10"x5") Max.Laminating Width 445mm (17.5") Max.Laminating Thickness 2mm (1/12") Film thickness 75~250mic(3~10 mil) Transport Type Four Roller (no carrier) Heat Source Hot roller Pre-Heating Time 4~5 min Temp. Operating Range 8 SETTINGS Cooling Fan Type DC FAN...
MAJOR PARTS IDENTIFICATION 1. Top Cabinet 2. Control Button Panel 3. LED 4. Input 5. Output 6. Power Cord EDNord - Istedgade 37A - 9000 Aalborg - Telefon 9633 3500...
3.INSTRUCTION OF BUTTONS AND LED 1. Press power button to turn laminator on or off. 2. When you press power button, "FUNC 2" LED is blinking. At this time, function NB-1900N buttons become available. 3. To choose film thickness, press and you will see the LED read-out.
LAMINATING STEPS 1. HOT LAMINATING 1. Press the power button. 2. Choose setting by 3. When red LED stops blinking and buzzer rings, you're ready to laminate. (It takes 4~5 minutes depending on setting function.) 4. Put document to be laminated, into a laminating pouch. Leave a minimum border of about 3mm(1/8"), to provide a proper edge seal.
1. Press the power button to turn laminator on. 2. Press COLD 3. It is ready when green LED blinking stops and buzzer rings. 4. Insert document into Royal Sovereign cold laminating pouch as follows. **HOW TO ATTACH DOCUMENT ON COLD POUCH FILM** 1) Prepare cold pouch film.
3. COLOR FOIL LAMINATING **Your laminator has ability to add color by using color foil to documents copied or printed by laser printer using toner.** **PAPER CARRIER is required** 1. Press the power button to turn laminator on. 2. Find FOIL setting, using 3.
4. MOUNTING BOARD LAMINATING **You can laminate photographs or pictures on a mounting board, less than 2mm (1/12") thick without any tension adjustment.** 1. Press the power button to turn the machine on. 2. Set FOIL setting with 3. When the LED light stops blinking and buzzer rings, the laminator is ready. 4.
CLEANING ROLLERS AND REMOVING FILM JAMMED OR STUCK TO ROLLERS 1. Cleaning rollers with a clean and thick paper 1) If film adhesive apears on the laminated pouch surface, Insert a sheet of clean, thick paper (about 0.5mm(1/50") thickness) into the machine 2~3 times on "FUNC 4" setting.
IMPORTANT SAFETY CONCERNS 1. Be sure that neckties, necklaces, long hair and loose clothing are kept away while the laminator is in operation. 2. Prevent children from accessing the machine. 3. Place the machine on a sturdy, flat work surface to prevent damage. 4.
Should product fail to operate during warranty period, return it, freight prepaid, to Royal Sovereign Corporation, 100 West Sheffield Avenue, Englewood, NJ 07631, for service. There will be no charge for parts and labor to repair or replace this product whthin warranty period.