Heat & Glo SL-350TRSI-AUE Installation And Operation Instructions Manual
  1. Manuals
  2. Brands
  3. Heat & Glo Manuals
  4. Indoor Fireplace
  5. SL-350TRSI-AUE
  6. Installation and operation instructions manual

Heat & Glo SL-350TRSI-AUE Installation And Operation Instructions Manual

Hearth and home technologies heater operation and maintenance manual sl-350trsi-aue
Hide thumbs Also See for SL-350TRSI-AUE:
Table of Contents

Advertisement

Quick Links

INSTALLATION AND OPERATION
INSTRUCTIONS
MODEL: SL-350TRSI-AUE
AUSTRALIAN GAS ASSOCIATION APPROVED
Approval Number 5666
THIS MANUAL MUST BE USED FOR INSTALLATION AND RETAINED
BY HOMEOWNER FOR OPERATION AND MAINTENANCE.
HEAT & GLO, a brand of Hearth & Home Technologies Inc.
20802 Kensington Boulevard, Lakeville, MN 55044 USA
www.heatnglo.com
THIS PRODUCT MAY BE COVERED BY ONE OR MORE OF THE FOLLOWING PATENTS:
(United States) 4593510, 4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495, 5452708, 5542407,
5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099, 6048195, 6053165, 6145502, 6170481, 6237588, 6296474,
6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, D320652, D445174, D462436; (Canada) 1297749,
2195264, 2225408; (Australia) 543790;586383; (Mexico) 97-0457; (New Zealand) 200265; or other U.S. and foreign patents pending.
Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06
1

Advertisement

Table of Contents
loading

Related Manuals for Heat & Glo SL-350TRSI-AUE

Summary of Contents for Heat & Glo SL-350TRSI-AUE

  • Page 1 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, D320652, D445174, D462436; (Canada) 1297749, 2195264, 2225408; (Australia) 543790;586383; (Mexico) 97-0457; (New Zealand) 200265; or other U.S. and foreign patents pending. Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06...
  • Page 2 Heat & Glo, a brand of Hearth & Home Technologies, Inc. 20802 Kensington Blvd., Lakeville, MN 55044, USA Copyright 2006 • Printed in U.S.A. Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 AND USING THIS APPLIANCE. instructions carefully during installation to ensure maximum benefit and safety.

  • Page 3: Table Of Contents

    3.2 Removal of Components for Service ... 33 3.3 Parts Replacement ... 33 3.4 Adjustments and Replacement Parts ... 33 3.5 Troubleshooting ... 34 4.0 Replacement Parts ... 35 Limited Warranty ... 37 Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 TABLE OF CONTENTS...
  • Page 4 5-5/8 in. (144mm) FLUE COLLAR COVER PLATE CONTROLS ACCESS ( BEHIND DOOR) Figure 1. Diagram of SL-350TRSI-AUE Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 11-3/8 in. (289mm) 15-7/8 in. (402 mm) Ø6-5/8 in. (167mm) 24 in.

  • Page 5: Installation Instructions

    Figure 2. Fireplace Dimensions, Locations, and Space Requirements Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 Clearance Requirements The top and back of fireplace are defined by stand-offs. The heat shield must be attached as shown if combus- tible materials are placed directly on top standoffs (Fig- ure 3).

  • Page 6: Introduction

    SOLID FUEL. These units MUST use the flue termination described in the flueing section of the manual. Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 from the Vent Pipe to Combustible Materials Inches Vertical Sections..1 ... 25 Horizontal Sections Top ...
  • Page 7 MINIMUM CLEARANCES REQUIRED FOR BALANCED FLUE TERMINALS OR THE FLUE TERMINALS OF OUTDOOR APPLIANCES Figure 5. Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 M = Gas meter P = Electricity meter or fuse box CLEARANCES 'n' (mm)

  • Page 8: Flue System Approvals And Installation

    SLK-01TRD SLK-991DA Figure 6. Flue Components and Terminations Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 FLUE TERMINATION APPROVALS DVP-TRAP2 & SLK-01TRD HORIZONTAL TERMINATION CAP DVP-TVHW & SLK-991DA VERTICAL TERMINATION CAP adhered to. The rise to run relationships are shown in the flueing drawings and tables on the next few pages.
  • Page 9 DVP45 217mm 319mm NOTE: PIPES OVERLAP 32mm AT EACH JOINT. Figure 7. DVP-Series Balanced Flue Component Specifications (127mm inner pipe / 203mm outer pipe) Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 152mm DVP6 610mm DVP24 DVP36...
  • Page 10 305-432mm 222mm SL-09D SL-24D SL-36D SL-48D SL-12/17D NOTE: PIPES OVERLAP 35mm AT EACH JOINT. Figure 8. SL D-Series Balanced Flue Component Specifications (102mm inner pipe / 168mm outer pipe) Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06...
  • Page 11 FT. (M) 36' MAXIMUM (10.97M) RESTRICTOR PLATE USE SL D-SERIES COMPONENTS ONLY. Figure 9. Figure 10. STRAIGHT OUT HORIZONTAL FLUEING Max. Run 24" (610mm) USE DVP-SERIES COMPONENTS ONLY. Figure 11. Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06...
  • Page 12 4' MIN. (1.22M) 12' MAX. (3.66M) V+H =36' MAX.(10.97M) H= 12' MAX. (3.66M) USE DVP-SERIES COMPONENTS ONLY. Figure 13. Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 FT. (M) 2' MAX.(0.61M) 4' MAX.(1.22M) 8' MAX.(2.44M) 10' MAX.(3.05M) ELBOW...
  • Page 13 10' MAX. (3.05M) 30' MAX.(9.14M) 10' MAX. (3.05M) USE SL D-SERIES COMPONENTS ONLY. Figure 14. Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 FLUEING WITH TWO (2) 90° ELBOWS FT. (M) 1' MIN.(0.30M) 2' MIN.(0.61M) 3' MIN.(0.91M) 4' MIN.(1.22M)
  • Page 14 4´ MIN. (1.22M) V + H + H USE DVP-SERIES COMPONENTS ONLY. Figure 15. Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 FLUEING WITH TWO (2) 90° ELBOWS 1´ MAX. (0.30M) 2´ MAX. (0.61M) 3´ MAX. (0.91M) 4´...
  • Page 15 4'MIN.(1.22M) 8' MAX.(2.44M) 5'MIN.(1.52M) 12' MAX.(3.66M) 12' MAX.(3.66M) NOTE: V + V MAX. 33' (10.06M) Figure 16. Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 H + H FT. (M) 4' MAX.(1.22M) 6' MAX (1.83M) 8' MAX.(2.44M)
  • Page 16 4´ MIN. (1.22M) 4´ MAX. (1.22M) V+H+H =30´ MAX.(9.14M) H = 4´MAX.(1.22M) Figure 17. Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 FLUEING WITH THREE (3) 90° ELBOWS V (FT.) H (FT.) 1´ MIN. (0.30M) 1´ MAX. (0.30M) 2´...
  • Page 17 HERE Figure 18. Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 WARNING: THE REAR FLUE COL- LAR SEAL CAP MUST REMAIN AT- TACHED TO THE REAR FLUE COL- LARS IF THE FLUE SYSTEM IS AT- TACHED TO THE TOP STARTING COLLARS.
  • Page 18 WARNING: ENSURE THAT THE HEATER GASKET SUPPLIED WITH THE HEATER SEALS BETWEEN THE FIRST FLUE COMPO- NENT AND THE OUTER HEATER WRAP. Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 WARNING Fire Risk Exhaust Fumes Risk Impaired Performance of Appliance •...
  • Page 19 PROCEED TO STEP 3 (Install Support Brackets) Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 B. On the TOP of the heater 1. Attaching the First Flue Component to the Start-...
  • Page 20 • The pipe opening of the firestops MUST BE placed towards the bottom of the firestop. • Continue the flue run through the firestop. Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 INTERIOR WALL SHIELD Figure 25.
  • Page 21 The other is attached to the termination cap in the same manner (see Figure 29). Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 • The heat shield sections will overlap to match the wall thickness (depth).

  • Page 22: Connecting The Gas Supply

    • Slide the termination cap over the end of the flue pipe and rotate the pipe clockwise 1/4 turn. Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 GAS ACCESS Figure 30. Gas Supply Line 1.3 CONNECTING THE GAS SUPPLY The gas is introduced to the appliance on the left hand side (see Figure 30).

  • Page 23: Ignition System Wiring

    BATTERY PORT ON/OFF SWITCH Figure 31. Electronic Ignition Wiring Diagram Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 CAUTION Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and danger- ous operation. Verify proper operation after servicing.

  • Page 24: Blower Fan

    The access hole for connecting the service wires is found on the right exterior side of the unit. See Figure 33 for wire connection detail. Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 • C RATED WIRE.

  • Page 25: Finishing

    OF FIREPLACE NON-COMBUSTIBLE STRIP Figure 34. Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 IF JOINTS BETWEEN THE FINISHED WALLS AND THE FIREPLACE SURROUND (TOP AND SIDES) ARE SEALED, A 300° F (149°C). MINIMUM SEAL- ANT MATERIAL MUST BE USED. THESE JOINTS ARE NOT REQUIRED TO BE SEALED.

  • Page 26: Installer Testing

    Lighting Instructions. Subsequent lightings of the appliance will not require such purging. Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 Follow the Safety Information and Lighting Instructions pages of this manual to light the appliance.

  • Page 27: Log Placement

    Place log #1 at the rear of the unit, with the left edge behind the tab on the pilot Locate the bottom groove of log #2 over the left most grate bar and align over Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 PILOT...
  • Page 28 LOG #5 (SRV438-724): Locate the top of log #5 onto log #1 and log #3, and place the bottom on the right side of the fourth log grate. Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06...
  • Page 29 LOG #6 (SRV540-704): Place log #6 against the second and third grate bars. If sooting occurs, the logs might need to be repositioned slightly to avoid excessive flame impingement. Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06...

  • Page 30: Operating Instructions

    BATTERY PORT ON/OFF SWITCH Figure 37. Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 OPERATING CAUTIONS • This appliance may exhibit a slight carbon deposition. • Do not place articles on or against this appliance. • Do not use or store flammable materials near this appliance.

  • Page 31: Safety And Lighting Information

    See installation and operating instructions accompany- ing appliance. Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 tact your dealer or a qualified service person to re- place the injector or adjust the valve. NOTE: THE TIPS OF THE FLAMES SHOULD NEVER HIT THE TOP OF THE FIREBOX.

  • Page 32: Fan Operation

    Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 When the appliance is put back in service check burner flame patterns with Figure 38.

  • Page 33: Removal Of Covers For Servicing

    RETAINING SCREWS Figure 41. CAUTION: ALL SCREWS WHICH WERE REMOVED MUST BE REPLACED. Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 2. PILOT ASSEMBLY/IGNITION SYSTEM • Remove the log set, log grate, metal base pan and burner.

  • Page 34: Troubleshooting

    3. Be sure glass is tighened properly on unit, particularly on top corners. Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 Corrective Actions...

  • Page 35: Replacement Parts

    4.0 REPLACEMENT PARTS Service Parts (NG, LP) Exploded Parts Diagram Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 Log set assembly SL-350TRSI-AUE Beginning Manufacturing Date: 6/06 Ending Manufacturing Date: ______...
  • Page 36 Pilot Bracket Valve Bracket Control Cable Rheostat Knob Mesh Assembly Exhaust Resistor Accesssories WSK-DLX-CE Conversion Kit NG Conversion Kit LP Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 PARTS PART NUMBER 2098-134 2098-135 582-844 582-055 530-302A 2089-010 2089-012...

  • Page 37: Limited Warranty

    HEAT & GLO reserves the right to make changes at any time, without notice, in design, material, specifications and prices. It also reserves the right to discontinue styles and products. Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 LIMITED 10 YEAR WARRANTY...
  • Page 38 For Service or Replacement Parts Contact: Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06 Melbourne Jetmaster 444 Swan Street Richmond 3121 (03) 9429-5573 Perth Fireplace Corner 277 Lord Street East Perth 6000 (08) 9228-2600 Sydney Jetmaster 10 Martin Avenue...

Table of Contents