Making Milk Based Drinks Automatically; Clean The Milk Frother By Using The Clean Button; White, Cappuccino, Latte And Milk Buttons; Programming The Quantity Of Coffee And Milk In The Cup For The Flat White, Cappuccino, Latte And Milk Buttons - DeLonghi ETAM36.365 Instructions For Use Manual

Bean to cup espresso and cappuccino machine
Hide thumbs Also See for ETAM36.365:
Table of Contents

Advertisement

No froth
Min. froth
Max. froth

Making milk based drinks automatically

The FLAT WHITE, CAPPUCCINO, LATTE and MILK buttons on the
control panel enable these drinks to be prepared automatically.
Proceed as follows:
1. Fill the milk container and attach it as described above.
2. Turn the froth adjustment dial on the milk container lid to
the position corresponding to the required froth.
3. Press the button corresponding to the required drink. The
name of the drink selected is displayed together with a
progress bar which gradually fills as preparation progress-
es.
4. After a few seconds, frothed milk is delivered from the
milk spout into the cup below.
For drinks with coffee, the machine automatically makes
the coffee after delivering the milk.
Please note!
If you want to interrupt preparation during delivery, press
any button.
At the end of delivery, to increase the quantity of milk or
coffee in the cup, within three seconds, just press and hold
the button corresponding to the cappuccino or milk based
coffee being made.
Do not leave the milk container out of the refrigerator
for long periods. The warmer the milk (5°C is ideal), the
poorer the quality of froth produced.

clean the milk frother by using the cLEAn button

Important! Danger of burns
When cleaning the internal tubes of the milk container, a little
hot water and steam leak out of the frothed milk spout.
Avoid contact with splashes of water.
"TURN DIAL TO CLEAN" flashes on the display each time you
use a milk function. To eliminate all milk residues, proceed as
follows:
1. Leave the milk container in the machine (you do not need
to empty it);
2. Place a cup or other recipient under the frothed milk
spout.
3. Turn the froth adjustment dial to "CLEAN" (fig. 25). "Clean-
FLAT WHITE/
MILK (hot milk)
LATTE
CAPPUCCINO/
MILK (frothed milk)
ing underway, Please wait" is displayed, together with a
progress bar which gradually fills as the operation pro-
ceeds. Cleaning stops automatically.
4. Turn the dial back to one of the froth selections.
5. Remove the milk container and always clean the steam
nozzle with a sponge (fig. 26).
Please note!
To prepare a number of cappuccinos and milk based cof-
fees, clean the milk container after you have prepared the
last drink only.
The milk container can be kept in the refrigerator.
In some cases, to clean you must wait for the appliance to
heat up.
programming the quantity of coffee and milk in the
cup for the FLAT WhiTE, cAppuccino, LATTE and MiLK
buttons
The appliance is set by default to automatically deliver stand-
ard quantities. To change these quantities, proceed as follows:
1. Place a cup under the coffee spouts and milk spout.
2. Press and hold one of the function buttons until the mes-
sage "Program quantity, PROGRAM MILK" is displayed.
3.
Release the button. The appliance starts delivering milk.
4. Once the required quantity of milk has been delivered into
the cup, press the button again.
5. The appliance stops delivering milk and, if required for
the drink being prepared, after a few seconds the coffee
is delivered into the cup. "Program quantity, PROGRAM
COFFEE" is displayed.
6. Once the required quantity of coffee has been delivered
into the cup, press the button again. Coffee delivery
stops.
The machine is now reprogrammed with the new milk and cof-
fee quantities.

DELiVErinG hoT WATEr AnD sTEAM

Important! Danger of burns.
Do not leave the appliance unattended while hot water or
steam is being delivered. The spout becomes hot during deliv-
ery. Hold by the handle only.
Please note!
If "Energy saving" is active, you may have to wait a few seconds
before hot water and steam are delivered.

Delivering hot water

1. Make sure the hot water spout is attached correctly (fig.
7).
2. Place a container under the spout (as close as possible to
14

Advertisement

Table of Contents
loading

Table of Contents