Toshiba PORTEGE S100 User Manual
  1. Manuals
  2. Brands
  3. Toshiba Manuals
  4. Laptop
  5. Portege S100 Series
  6. User manual
Toshiba PORTEGE S100 User Manual

Toshiba PORTEGE S100 User Manual

Portable personal computer
Hide thumbs Also See for PORTEGE S100:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Maintenance Manual
PORTÉGÉ S100
TOSHIBA
PORTÉGÉ S100
Portable Personal Computer
User's Manual

Advertisement

Table of Contents
loading

Related Manuals for Toshiba PORTEGE S100

Summary of Contents for Toshiba PORTEGE S100

  • Page 1 PORTÉGÉ S100 TOSHIBA PORTÉGÉ S100 Portable Personal Computer User’s Manual...
  • Page 2 User’s Manual Copyright © 2005 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
  • Page 3 EU Declaration of Conformity This product is carrying the CE-Mark in accordance with the related European Directives. Responsible for CE-Marking is TOSHIBA Europe GmbH, Hammfelddamm 8, 41460 Neuss, Germany. The complete and official EU Declaration of Conformity can be found on TOSHIBA’s web site http://epps.toshiba-teg.com on the Internet.
  • Page 4 User’s Manual Description on Laser specification The optical drive such as DVD-ROM&CD-R/RW drive and DVD Super Multi drive that is used in this computer is equipped with laser. The classification label with the following sentence is affixed to the surface of the drive. CLASS 1 LASER PRODUCT LASER KLASSE 1 LUOKAN 1 LASERLAITE...

  • Page 5: Table Of Contents

    PORTÉGÉ S100 Table of Contents General Precautions Preface Manual contents ........... . . xiii Conventions.
  • Page 6 TOSHIBA Password Utility ........
  • Page 7 TOSHIBA support ........
  • Page 8 Table of Contents viii User’s Manual...

  • Page 9: General Precautions

    PORTÉGÉ S100 General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.
  • Page 10 (41°F to 86°F) or >25°C (77°F) at high altitude (all temperature references are approximate and may vary depending on the specific computer model - please refer to your PC documentation or visit the Toshiba website at www.pcsupport.toshiba.com for details). CPU performance may also vary from specifications due to design configuration.

  • Page 11: Copy Protection

    For optimum performance, use your computer product only under recommended conditions. Read additional restrictions under “Environmental Conditions” in your PC documentation. Contact Toshiba technical service and support, refer to TOSHIBA support...
  • Page 12 General Precautions User’s Manual...

  • Page 13: Preface

    PORTÉGÉ S100 Preface Congratulations on your purchase of the PORTÉGÉ S100 computer. This powerful notebook computer provides excellent expansion capability, including multimedia devices, and it is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your PORTÉGÉ S100 computer.

  • Page 14: Conventions

    Preface Chapter 4, Operating Basics, includes instructions on using the following devices: Touch Pad, USB floppy disk drive (optional), Ultra Slim Bay modules, optical media drives, sound system, modem, Wireless communication features, LAN. It also provides tips on care of the computer, floppy disks and CD/DVDs.
  • Page 15 Preface Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C.
  • Page 16 Preface User’s Manual...

  • Page 17: Introduction

    Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.

  • Page 18: Documentation And Backup Media

    Windows XP Professional The following software is preinstalled: ® Microsoft Windows XP Professional Microsoft Internet Explorer TOSHIBA Utilities TOSHIBA SD Memory Boot Utility DVD Video Player TOSHIBA Touch pad On/Off utility TOSHIBA Power Saver TOSHIBA Mobile Extension TOSHIBA Assist TOSHIBA ConfigFree...

  • Page 19: Features

    Introduction Features The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer incorporates the following features and benefits: Processor Built-in The computer is equipped with an Intel ®...
  • Page 20 Introduction Power Battery pack The computer is powered by one rechargeable lithium-ion battery pack. RTC battery The internal RTC battery backs up the Real Time Clock (RTC) and calendar. AC adaptor The AC adaptor provides power to the system and recharges the batteries when they are low. It comes with a detachable power cord.
  • Page 21 Introduction DVD-ROM&CD-R/RW Some models are equipped with a full-size, drive DVD-ROM&CD-R/RW drive module that lets you run CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R at maximum 24 speed and CD-RW at maximum 24 speed.
  • Page 22 Introduction Display The computer’s LCD display panel supports high-resolution video graphics. The LCD screen can be set at a wide range of viewing angles for maximum comfort and readability. Built-in 14.1" TFT LCD screen, 16 M colors, with one of the following resolutions: XGA, 1024 horizontal ×...
  • Page 23 Introduction Infrared The serial infrared port is compatible with Infrared Data Association (IrDA 1.1) standards. It enables cableless 4 Mbps, 1.152 Mbps, 115.2 kbps, 57.6 kbps, 38.4 kbps, 19.2 kbps or 9.6 kbps data transfer with IrDA 1.1 compatible external devices. Slots PC card The PC card slot accommodates a Type II card.
  • Page 24 Ultra Slim Bay is a single-drive bay that Modules accommodates a DVD-ROM&CD-R/RW drive, DVD Super Multi drive and secondary hard disk drive. The TOSHIBA Mobile Extension enables hot insertion of modules when you are using a plug and play operating system. Ultra Slim Bay...

  • Page 25: Special Features

    The lock screw is inserted in the unlock position when purchased. Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. TOSHIBA Assist Press this button to launch an application button automatically.
  • Page 26 Use the Cooling Method item of the Basic Setup tab in TOSHIBA Power Saver. Maximum Turns on fan first, then if...
  • Page 27 Data is maintained in the computer’s main memory. When you turn on the power again, you can continue working right where you left off. TOSHIBA RAID RAID (Redundant Array of Independent Disks) realizes fault tolerance (mirroring = RAID1), which is configured by arraying multiple independent hard disk drives.

  • Page 28: Utilities

    InterVideo WinDVD, then click InterVideo WinDVD. TOSHIBA SD The TOSHIBA SD memory boot utility is a utility Memory Boot Utility which can create SD memory card to a boot disk. You can boot TOSHIBA SD Memory Boot Utility from the menu bar as follows.
  • Page 29 Advanced Port Repricator III. To open the property dialog, select TOSHIBA Mobile Extension from TOSHIBA Assist. TOSHIBA ConfigFree TOSHIBA ConfigFree is a suite of utilities to allow easy control of communication devices and network connections. TOSHIBA ConfigFree also allows you to find communication problems and create profiles for easy switching between locations and communication networks.
  • Page 30 If a secondary hard disk drive is installed in the Console Ultra Slim Bay in addition to the built-in HDD, you can use the TOSHIBA RAID Console to create or manage a RAID array. To start the utility, click start, point to All Programs, point to TOSHIBA, point to RAID and click RAID Console.
  • Page 31 “F number” key. The Fn key remains active until another key is pressed. DLA for TOSHIBA DLA (Drive Letter Access) is the packet writing software which provides the function which writes...

  • Page 32: Options

    A 256, 512 or 1,024 MB memory module (DDR2-533/400) can easily be installed in the computer. Battery pack An additional battery pack can be purchased from your TOSHIBA dealer. Use it as a spare or replacement. High capacity battery An additional battery pack can be purchased pack from your TOSHIBA dealer.
  • Page 33 Introduction Ultra Slim Bay options The following modules can be installed in the Ultra Slim Bay. All other modules are options. DVD-ROM&CD-R/RW Refer to the Features section for details. DVD Super Multi Refer to the Features section for details. Ultra Slim Bay HDD An adaptor lets you install an optional HDD adaptor (Black) described in Chapter 8,...
  • Page 34 Introduction 1-18 User’s Manual...

  • Page 35: Chapter 2 : The Grand Tour

    PORTÉGÉ S100 Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Certain notebook chassis are designed to accommodate all possible configurations for an entire product series. Your selected model may not have all the features and specifications corresponding to all of the icons or switches shown on the notebook chassis, unless you have selected all those features.

  • Page 36: Left Side

    The Grand Tour Set the switch to off in airplanes and hospitals. Check the wireless communication indicator. It will stop glowing when the wireless communication function is off. Microphone jack A 3.5 mm mini microphone jack enables connection of a three-conductor mini jack for monaural microphone input.
  • Page 37 The Grand Tour LAN jack This jack lets you connect to a LAN. The adaptor has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T), Fast Ethernet LAN (100 megabits per second, 100BASE-TX) and Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T).

  • Page 38: Right Side

    The Grand Tour Keep foreign objects out of the SD card slot. A pin or similar object can damage the computer’s circuitry. Right side The following figure shows the computer’s right side. Ultra Slim Bay External monitor port The right side of the computer Ultra Slim Bay A DVD-ROM&CD-R/RW drive, DVD Super Multi drive and Ultra Slim Bay HDD adaptor can be...

  • Page 39: Underside

    The Grand Tour Keep foreign objects out of the USB connectors. A pin or similar object can damage the computer’s circuitry. Operation of all functions of all USB devices has not been confirmed. Some functions might not execute properly. DC IN 15V jack The AC adaptor connects to this jack.
  • Page 40 The Grand Tour Battery lock Slide this lock to release the battery pack for removal. Battery pack The battery pack powers the computer when the AC adaptor is not connected. For detailed information on the battery pack, refer to Chapter 6, Power and Power-Up Modes.

  • Page 41: Front With The Display Open

    Power button LCD Sensor switch Touch Pad (Not shown) control buttons TOSHIBA Assist Button TOSHIBA Presentation Button The front of the computer with the LCD panel open Display hinge The display hinge holds the LCD display panel at easy-to-view angles.
  • Page 42 LCD and CRT. You can also return to single display by pressing this button twice. The setting of TOSHIBA Presentation button can be changed through the properties of TOSHIBA Controls. Display mode is changed to the multi-monitor display by selecting “Different Image”...

  • Page 43: System Indicators

    Hibernation mode. Use the TOSHIBA Power Saver Utility to enable or disable this feature. The default is “enabled”. Refer to the TOSHIBA Power Saver Utility and Panel Power Off/On items in Chapter 1, Special features, for details on settings.

  • Page 44: Keyboard Indicators

    The Grand Tour Battery The Battery indicator shows the condition of the battery’s charge: Green indicates full charge, orange indicates battery charging and flashing orange indicates a low battery charge. Refer to Chapter 6, Power and Power-Up Modes. The HDD indicator glows green when the computer is accessing the built-in hard disk.

  • Page 45: Usb Floppy Disk Drive (Optional)

    The Grand Tour Arrow mode indicator Numeric mode indicator Keypad overlay indicators Arrow mode When the Arrow mode indicator lights green, you can use the keypad overlay (gray labeled keys) as cursor keys. Refer to the Keypad overlay section in Chapter 5, The Keyboard. Numeric mode You can use the keypad overlay (gray labeled keys) for numeric input when the Numeric mode...

  • Page 46: Optical Media Drives

    The Grand Tour Floppy disk slot Insert a floppy disk in this slot. Eject button When a floppy disk is fully seated in the drive, the eject button pops out. To remove a floppy disk, push in the eject button and the floppy disk pops out partially for removal.

  • Page 47: Writable Discs

    The Grand Tour Writable discs This section describes the types of writable CD/DVD discs. Check the specifications for your drive to for the type of discs it can write. Use RecordNow! to write compact discs. Refer to Chapter 4, Operating Basics.

  • Page 48: Ac Adaptor

    The Grand Tour DVD Super Multi drive The full-size DVD Super Multi drive module lets you record data to rewritable CDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. The read speed is slower at the center of a disc and faster at the outer edge.
  • Page 49 Use only the AC adaptor that came with the computer or an equivalent optional adaptor. Use of any other adaptors could damage your computer. TOSHIBA assumes no liability for any damage in such case. Use only the AC adaptor supplied as an accessory. Other AC adaptors have different voltage and terminal polarities and use of them may produce heat and smoke or even result in fire or rupture.
  • Page 50 The Grand Tour 2-16 User’s Manual...

  • Page 51: Getting Started

    PORTÉGÉ S100 Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: Setting up your work space — for your health and safety Be sure also to read Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.

  • Page 52: General Conditions

    Getting Started General conditions In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment. Make sure there is adequate space around the computer for proper ventilation. Make sure the AC power cord connects to an outlet that is close to the computer and easily accessible.

  • Page 53: Seating And Posture

    Getting Started Seating and posture The height of your chair in relation to the computer and keyboard as well as the support it gives your body are primary factors in reducing work strain. Refer to the following tips. Below eye level 90°angles Foot rest Posture and positioning of the computer...

  • Page 54: Connecting The Ac Adaptor

    Getting Started Work habits A key to avoiding discomfort or injury from repetitive strain is to vary your activities. If possible, schedule a variety of tasks into your workday. If you must spend long periods at the computer, finding ways to break up the routine can reduce stress and improve your efficiency.
  • Page 55 Use only the AC adaptor supplied with your computer or an equivalent adaptor that is compatible. Use of any incompatible adaptor could damage your computer. TOSHIBA assumes no liability for any damage caused by use of an incompatible adaptor. The supplied power cord conforms to safety rules and regulations in the region the product is bought and should not be used outside this region.

  • Page 56: Opening The Display

    Getting Started 2. Connect the AC adaptor’s DC output plug to the DC IN 15V jack on the back of the computer. DC IN 15V jack Connecting the adaptor to the computer 3. Plug the power cord into a live wall outlet. The Battery and DC IN indicators on the front of the computer should glow.

  • Page 57: Turning On The Power

    Getting Started Turning on the power This section describes how to turn on the power. The Power button LED indicates the status. Refer to the Power indicators section in Chapter 6, Power and Power-Up Modes. After you turn on the power for the first time, do not turn it off until you have set up the operating system.

  • Page 58: Turning Off The Power

    Getting Started Turning off the power The power can be turned off in one of the following modes: Shut down (Boot), Hibernation or Standby mode. Shut Down mode (Boot mode) When you turn off the power in Shut Down mode no data is saved and the computer will boot to the operating system’s main screen.

  • Page 59: Starting Hibernation

    For the computer to shut down in hibernation mode, the hibernation feature must be enabled in two places: the Hibernate tab in Power Options and Setup Action tab in TOSHIBA Power Saver. Otherwise, the computer will shut down in Standby mode. If battery power becomes depleted, data saved in Standby mode will be lost.

  • Page 60: Standby Mode

    When the AC adaptor is connected, the computer will go into Standby mode according to the settings in the TOSHIBA Power Saver utility. To restore operation from Standby mode, press the power button or press any key. The latter action works only if Wake-up on Keyboard is enabled in HW Setup.

  • Page 61: Restarting The Computer

    1. Click start, click Turn Off Computer and click Stand By. 2. Close the computer’s LCD display panel. This feature must be enabled. Refer to the Setup Action tab in TOSHIBA Power Saver Utility described in the Control Panel. Open Performance and Maintenance and open TOSHIBA Power Saver.

  • Page 62: Restoring The Preinstalled Software

    Restoring TOSHIBA utilities and drivers If Windows is working properly, individual drivers or applications can be separately restored. The TOSHIBA Tools & Utilities folder (C:\TOOLSCD) contains drivers and applications, which are included with your computer system. If your system drivers or applications have become damaged in some way, you can reinstall most of the components from this folder.

  • Page 63: Operating Basics

    PORTÉGÉ S100 Chapter 4 Operating Basics This chapter gives information on basic operations including using the Touch Pad, USB floppy disk drive (optional), changing Ultra Slim Bay modules, optical media drives, Sound System, Modem, Wireless communication features and LAN. It also provides tips on caring for your computer, floppy disks and CD/DVDs.

  • Page 64: Using The Usb Floppy Disk Drive (Optional)

    Operating Basics Using the USB floppy disk drive (optional) USB floppy disk drive connects to the computer’s USB port. It accommodates 1.44-megabyte or 720-kilobyte floppy disks. Refer to Chapter 2, The Grand Tour, for more information. Option or provided with some models. Connecting USB floppy disk drive To connect the drive, plug the floppy disk drive’s USB connector into a computer’s USB port.

  • Page 65: Changing Ultra Slim Bay Modules

    Ultra Slim Bay weight saver. To avoid injury, do not put your hand into the Ultra Slim Bay slot. The TOSHIBA Mobile Extension is preinstalled to support hot swapping under Windows. Refer to Chapter 1, Introduction, for information on using this utility to change modules while the computer’s power is on.

  • Page 66: Inserting A Module

    Operating Basics 6. Grasp the optical media drive and slide it out. The optical media drive and other Ultra Slim Bay modules can become hot with use. Be careful when removing the module. Store the DVD Super Multi drive unit in the Ultra Slim Bay Case when removing it from the computer or transporting it.

  • Page 67: Using Optical Media Drives

    Operating Basics Using optical media drives The full-size drive provides high-performance execution of CD/DVD-ROM- based programs. You can run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without an adaptor. An ATAPI interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVD-ROM, an indicator on the drive glows and the Ultra Slim Bay indicator glows.
  • Page 68 Operating Basics 2. Grasp the disc tray gently and pull until it is fully opened. Disc tray Pulling the disc tray open 3. Lay the CD/DVD, label side up, in the disc tray. Laser lens Inserting a CD/DVD When the disc tray is fully opened, the edge of the computer will extend slightly over the CD/DVD tray.

  • Page 69: Removing Discs

    Operating Basics 5. Push the center of the disc tray to close it. Press gently until it locks into place. If the CD/DVD is not seated properly when the disc tray is closed, the CD/DVD might be damaged. Also, the disc tray might not open fully when you press the eject button.

  • Page 70: Writing Cds On Dvd-Rom&Cd-R/Rw Drive

    Operating Basics How to remove CD/DVD when the disk tray will not open Pressing the eject button will not open the disc tray when the computer power is off. If the power is off, you can open the disc tray by inserting a slender object (about 15 mm) such as a straightened paper clip into the eject hole just to the right of the eject button.

  • Page 71: Before Writing Or Rewriting

    Ultra-Speed CD-RW: MITSUBISHI CHEMICAL CORPORATION TOSHIBA has confirmed the operation of CD-R and CD-RW media of the manufacturers above. Operation of other media cannot be guaranteed. The actual number of rewrites to CD-RW is affected by the quality of the disc and the way it is used.

  • Page 72: Writing Cd/Dvds On Dvd Super Multi Drive

    Operating Basics When writing or rewriting Note the following when you write or rewrite a CD-R or CD-RW. Always copy data from the HDD to the CD. Do not use cut-and-paste. The original data will be lost if there is a write error. Do not perform any of the following actions: Change users in the Windows XP operating system.
  • Page 73 Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of CD-R/RW and DVD-R/+R/-RW/+RW/-RAM disc. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates.
  • Page 74 Operating Basics DVD-RW: DVD Specifications for Recordable Disc for Version 1.1 or version 1.2 VICTOR COMPANY OF JAPAN.LIMITED MITSUBISHI CHEMICAL CORPORATION DVD+RW: MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. DVD-RAM: DVD Specifications for DVD-RAM Disc for Version 2.0 or Version 2.1 Matsushita Electric Industrial Co., Ltd.

  • Page 75: When Writing Or Rewriting

    Operating Basics When multiple drives that can write data to discs are connected, be careful not to write to the wrong drive. Be sure to connect the AC adaptor before you write or rewrite. Before you enter standby/hibernation mode, be sure to finish DVD-RAM writing.
  • Page 76 Always copy data from the HDD to the DVD-RAM. Do not use cut-and-paste. The original data will be lost if there is a write error. RecordNow! Basic for TOSHIBA Note the following limitations when you use RecordNow!: DVD-Video cannot be created using RecordNow!.

  • Page 77: Data Verification

    3. Mark the Verify data written to the disc after burning check box in the Data Options. Click the OK button. DLA for TOSHIBA Note the following limitations when you use DLA: This software supports only rewritable discs (DVD+RW, DVD-RW, and CD-RW).

  • Page 78: When Using Windvd Creator Platinum

    Operating Basics When using WinDVD Creator Platinum You can record video back to your digital camcorder via i.LINK (IEEE1394) using WinDVD Creator Platinum. However, there is a case where its playback sound is choppy. 1. Click start and select the Control Panel. 2.

  • Page 79: Important Information For Use

    Operating Basics Important information for use Note the following limitations when you write video DVD: 1. Editing digital video Log in with Administrator rights to use WinDVD Creator. Make sure that your computer is running on AC power when using WinDVD Creator.

  • Page 80: Media Care

    Operating Basics Please verify your disc after recording important data. DVD-R/+R/-RW disc cannot be written in VR format. WinDVD Creator cannot export to DVD-Audio, VideoCD, miniDVD format. WinDVD Creator can write DVD-RAM/+RW in VR format, but the disc may only play on your computer. When writing to DVD disc, WinDVD Creator requires 2GB or more over disk space every one hour of video.

  • Page 81: Sound System

    Operating Basics 6. If your CD/DVDs become dusty or dirty, wipe them with a clean dry cloth. Wipe from the center out, do not wipe in a circular direction around the CD/DVD. If necessary, use a cloth dampened in water or a neutral cleaner.

  • Page 82: Soundmax Control Panel

    TOSHIBA Mic Effect will reduce these echoes generated on your computer. Form more information on using the TOSHIBA Mic Effect, refer to its help. 4-20 User’s Manual...

  • Page 83: Modem

    To select a region, follow the steps below. 1. Click start, point to All Programs, point to TOSHIBA, point to Networking and click Modem Region Select. Do not use the Country/Region Select function in the Modem setup utility in the Control Panel if the function is available.

  • Page 84: Modem Selection

    Operating Basics Setting You can enable or disable the following settings: AutoRun Mode The Region Select utility starts automatically when you start up the operating system. Open the Dialing Properties dialog box after selecting region. The dialing properties dialog box will be displayed automatically after you select the region.

  • Page 85: Wireless Communications

    Operating Basics 1. Plug one end of the modular cable into the computer’s modem jack. 2. Plug the other end of the modular cable into a telephone jack. Modular cable Telephone jack Modem jack Modem jack Connecting the internal modem Do not pull on the cable or move the computer while the cable is connected.

  • Page 86: Wireless Communication Switch

    TOSHIBA strongly recommend the customer to enable the WEP function. TOSHIBA is not liable for the eavesdropping of data due to the use of Wireless LAN and the damage thereof. Wireless communication switch You can enable or disable Wireless LAN function, with the on/off switch.

  • Page 87: Lan

    Operating Basics Wireless communication Indicator The wireless communication indicator indicates the status of the wireless communication functions. Indicator status Indication Indicator off Wireless communication switch is set to off. Automatic power down because of overheating. Power malfunction Indicator glows Wireless communication switch is on. Wireless LAN is turned on by an application.

  • Page 88: Connecting Lan Cable

    Operating Basics Connecting LAN cable To connect the LAN cable, follow the steps below. Connect the AC adaptor before connecting the LAN cable. The AC adaptor must remain connected during LAN use. If you disconnect the AC Adaptor while the computer is accessing a LAN, the system may hang up.

  • Page 89: Cleaning The Computer

    Operating Basics Cleaning the computer To help ensure long, trouble-free operation, keep the computer free of dust and use care with liquids around the computer. Be careful not to spill liquids into the computer. If the computer does get wet, turn the power off immediately and let the computer dry completely before you turn it on again.

  • Page 90: Using The Hard Disk Drive (Hdd) Protection

    Operating Basics Using the Hard Disk Drive (HDD) Protection There is a function for reducing the risk of damage on HDD in this computer. Using the acceleration sensor built in the computer, HDD Protection detects vibration, shocks and similar signs in the computer, and automatically moves the HDD head to a safe position in order to reduce the risk of damage that could be caused by a head-to-disk contact.

  • Page 91: Toshiba Hdd Protection Properties

    Operating Basics TOSHIBA HDD Protection Properties You can make the HDD Protection settings by using the TOSHIBA HDD Protection Properties window. To open the window, click start point to All Programs point to TOSHIBA point to Utilities and click HDD Protection setting.

  • Page 92: Detail Properties

    Operating Basics Detail Properties To open the Detail Properties window, click the Setup Detail button in the TOSHIBA HDD Protection Properties window. Detail Properties Detection Level Amplification When the AC adaptor is disconnected or the lid is closed, HDD Detection assumes that the computer will be carried and sets the detection level to the maximum for 10 seconds.

  • Page 93: Heat Dispersal

    CPU speed. Or, by lowering the CPU speed first, then if necessary, turning on the fan. Use the Cooling Method item of the Basic Setup tab in TOSHIBA Power Saver. Maximum Turns on the fan first, then if necessary, lowers the CPU Performance processing speed.
  • Page 94 Operating Basics 4-32 User’s Manual...

  • Page 95: Chapter 5 : The Keyboard

    PORTÉGÉ S100 Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with.

  • Page 96: Function Keys: F1

    The function executed by individual keys depends on the software you are using. Soft keys: Fn key combinations The Fn (function) is unique to TOSHIBA computers and is used in combination with other keys to form soft keys. Soft keys are key combinations that enable, disable or configure specific features.

  • Page 97: Hot Keys

    The Keyboard Press Fn + F10 or Fn + F11 to access the integrated keypad. When activated, the keys with gray markings on the bottom edge become numeric keypad keys (Fn + F11) or cursor control keys (Fn + F10). Refer to Keypad overlay section in this chapter for more information on how to operate these keys.
  • Page 98 Fn, and release and press F2 again to toggle between the settings. Release both Fn and F2 to put the new setting into effect. You can also change this setting through the Profile options in TOSHIBA Power Saver.
  • Page 99 You can also change this setting through the Screen brightness item of the Basic Setup tab in TOSHIBA Power Saver. The brightness level is always set at the maximum value for about 18 seconds, when the internal LCD screen turns on.

  • Page 100: Fn Sticky Key

    Fn key. Fn Sticky key You can use the TOSHIBA Accessibility Utility to make the Fn key sticky, that is, you can press it once, release it, and then press an “F number” key. To start the TOSHIBA Accessibility Utility, click start, point to All Programs, point to TOSHIBA, point to Utilities and click Accessibility.

  • Page 101: Windows Special Keys

    The Keyboard Windows special keys The keyboard provides two keys that have special functions in Windows: Windows logo key activates the start menu and the other, the application key, has the same function as the secondary mouse button. This key activates the Windows start menu. This key has the same function as the secondary mouse button.

  • Page 102: Numeric Mode

    The Keyboard Numeric mode To turn on the Numeric mode, press Fn + F11. The Numeric mode indicator lights. Now try numeric data entry using the keys in the figure below. Press Fn + F11 again to turn off the overlay. The numeric keypad overlay Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard...

  • Page 103: Generating Ascii Characters

    The Keyboard Temporarily changing modes If the computer is in Numeric mode, you can switch temporarily to Arrow mode by pressing a shift key. If the computer is in Arrow mode, you can switch temporarily to Numeric mode by pressing a shift key. Generating ASCII characters Not all ASCII characters can be generated using normal keyboard operation.
  • Page 104 The Keyboard 5-10 User’s Manual...

  • Page 105: Chapter 6 : Power And Power-Up Modes

    PORTÉGÉ S100 Chapter 6 Power and Power-Up Modes The computer’s power resources include the AC adaptor, battery pack and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes.

  • Page 106: Power Indicators

    Power and Power-Up Modes Table 6-1 Power conditions continued Power on Power off (no operation) Battery charge • Operates adaptor is above low • LED: Battery off battery trigger DC IN off connected point Battery charge • Operates is below low •...

  • Page 107: Battery Types

    Power and Power-Up Modes DC IN indicator Check the DC IN indicator to determine the power status with the AC adaptor connected: Indicates the AC adaptor is connected and Green supplying proper power to the computer. Indicates a problem with the power supply. Flashing orange Plug the AC adaptor into another power outlet.
  • Page 108 Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. Do not remove the battery pack while the computer is in Standby mode. Data is stored in RAM, so if the computer loses power it will be lost.

  • Page 109: Care And Use Of The Battery Pack

    The computer’s RTC battery is a Ni-MH battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations.
  • Page 110 Never use the computer again until it has been checked by a TOSHIBA service provider. It might generate smoke or fire, or the battery pack might rupture. 3. Make sure the battery is securely installed in the computer before attempting to charge the battery pack.
  • Page 111 2. Never dispose of battery packs with normal trash. Bring them to your TOSHIBA dealer or to another recycling center to save resources and prevent environmental damage. Cover the terminals with electrical tape to prevent short-circuits, which could cause the battery pack to ignite or rupture.

  • Page 112: Charging The Batteries

    The Battery indicator glows orange when the battery is being charged. Use only the computer connected to an AC power source or the optional TOSHIBA Battery charger to charge the battery pack. Never attempt to charge the battery pack with any other charger.

  • Page 113: Battery Charging Notice

    Therefore, an often used, older battery will not operate for as long as a new battery even when both are fully charged. In this case, TOSHIBA Power Saver will indicate a 100% charge for both the old and new battery, but the displayed estimated time remaining will be shorter for the older battery.

  • Page 114: Maximizing Battery Operating Time

    How you configure the computer (for example, whether you enable battery-power saving options). The computer provides a battery save mode, which can be set in TOSHIBA Power Saver, to conserve battery power. This mode has the following options: CPU Processing speed...

  • Page 115: Replacing The Battery Pack

    Power and Power-Up Modes Extending battery life To maximize the life of your battery pack: At least once a month, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges. Before doing so, follow the steps below. 1.

  • Page 116: Removing The Battery Pack

    Power and Power-Up Modes Removing the battery pack To replace a discharged battery pack, follow the steps below. When handling battery packs, do not short-circuit the terminals. Also do not drop, hit or otherwise apply impact; do not scratch or break the casing and do not twist or bend the battery pack.

  • Page 117: Installing The Battery Pack

    7. Return your computer to the upright position. For environmental reasons, do not throw away a spent battery pack. Please return spent battery packs to your TOSHIBA dealer. Installing the battery pack To install a battery pack, follow the steps below.

  • Page 118: Toshiba Password Utility

    Power and Power-Up Modes TOSHIBA Password Utility The TOSHIBA Password Utility provides two levels of password security: User and Supervisor. Passwords set in TOSHIBA Password Utility are different from the Windows password. User password To start the utility, point to or click the following items: start ->...

  • Page 119: Supervisor Password

    If an unformatted card or one with an incompatible format is inserted, you will be prompted to format it with a tool named TOSHIBA SD Memory Card Format. To start the format tool, point to or click the following items: start ->...

  • Page 120: Power-Up Modes

    Turning off the power in Chapter 3, Getting Started. Windows utilities You can specify the setting in TOSHIBA Power Saver. Hot keys You can use hot keys Fn + F3 to enter Standby mode and Fn + F4 to enter Hibernation.

  • Page 121: Panel Power On/Off

    Power and Power-Up Modes Panel power on/off You can set up your computer so that power turns off automatically when you close the computer’s LCD display panel. When you open the computer’s LCD display panel, power turns on in Standby or Hibernation mode but not in boot mode.
  • Page 122 Power and Power-Up Modes 6-18 User’s Manual...

  • Page 123: Chapter 7 : Hw Setup

    PORTÉGÉ S100 Chapter 7 HW Setup This chapter explains how to use TOSHIBA HW Setup program to configure your computer. TOSHIBA HW Setup lets you configure settings for General, Display, Boot Priority, Keyboard, CPU, LAN, Device Config, Parallel/Printer and USB.

  • Page 124: Power On Display

    HW Setup General This window displays the BIOS version and contains two buttons: Default and About. Return all HW Setup values to the factory settings. Default Display the HW Setup version. About Setup This field displays BIOS Version and date. Display This tab lets you customize your computer’s display settings for either the internal LCD screen or for an external monitor.

  • Page 125: Boot Priority

    HW Setup Boot Priority Boot Priority Options This option sets the priority for booting the computer. Select from the following settings: HDD −> FDD −> The computer looks for bootable files in the CD-ROM −> LAN following order: HDD, floppy disk drive* CD-ROM* and LAN (Default).
  • Page 126 HW Setup To change the boot drive, follow the steps below. 1. Hold down F12 and boot the computer. 2. The following menu will be displayed with the following icons: Built-in HDD, Ultra Slim Bay HDD, CD-ROM, FDD (or SD memory card), Network (LAN) boot.
  • Page 127 HW Setup If a boot command is not found on the first detected HDD, the system will not boot from the other HDD. It will search the next device in the boot priority for a boot command. Some modules may not be displayed. Keyboard External Keyboard Fn key Use this option to set a key combination on an external keyboard to...
  • Page 128 HW Setup This function lets you set the CPU operating mode. ® It is displayed in Pentium-M model only. Dynamic CPU Frequency Mode This option lets you choose from the following settings: CPU power consumption and clock speed Dynamically automatic switching function is enabled. Switchable When the computer is in use, CPU operation is automatically switched when necessary...

  • Page 129: Device Config

    HW Setup Device Config Device Configuration This option lets you set the device configuration. BIOS sets all devices. All Devices Operating system sets devices that it can control Setup by OS (Default). PCI Express Link ASPM This feature lets you set the PCI Express power-saving configuration. Enables power-saving when the PCI Express Enabled device is not being used.

  • Page 130: Configuring The Execute-Disable Bit Capability And Tpm

    Notes before using the BIOS Setup In normal cases, changes in system configuration should be made in Windows using TOSHIBA HW Setup, TOSHIBA Password Utility, TOSHIBA Power Saver, Device Manager, etc. If the configuration in the BIOS setup program is different from the configuration in the Windows utility, the configuration in the Windows utility takes priority.

  • Page 131: Starting And Ending The Bios Setup Program

    1. Switch on your computer while pressing the Esc key. If “Password =” is displayed, enter the user password and press the Enter key. Please refer to Chapter 6, the TOSHIBA Password Utility, for details about the user password. The “Check system. Then press [F1] key.” message is displayed.

  • Page 132: Security Controller

    System configuration changes other than changes to this setting should be made in Windows using TOSHIBA HW Setup, TOSHIBA Password Utility, TOSHIBA Power Saver, Device Manager, etc. When using TPM, please install the Infineon TPM Installation Guide from the TOSHIBA Application Installer.

  • Page 133: Optional Devices

    PORTÉGÉ S100 Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility. This chapter describes connection or installation of the following devices, which are available from your TOSHIBA dealer: Cards/memory PC card SD card Memory expansion...

  • Page 134: Pc Card

    The computer is equipped with a PC card slot that can accommodate a Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards.

  • Page 135: Sd Card

    Optional Devices Removing a PC card To remove the PC card, follow the steps below. 1. Open the Safely Remove Hardware icon on the Task Bar. 2. Point to PC card and click. 3. Press the PC card eject button to extend it. If the PC card is not inserted all the way, the eject button may not pop out.

  • Page 136: Formatting An Sd Memory Card

    SD memory cards are sold with format in conformity to the Standards of SD memory card. If you format the SD card again, be sure to format it with the utility of TOSHIBA SD memory card format, not in the format defined as the Windows standard format.

  • Page 137: Memory Expansion

    8. Do not touch the metal part or expose it to liquids or let it get dirty. Creation of a boot disk In TOSHIBA SD Memory Boot Utility, a boot disk can be created with SD memory card. Refer to the Utilities of Chapter 1, Introduction for details.

  • Page 138: Installing A Memory Module

    Optional Devices Use only memory modules approved by TOSHIBA. Do not try to install or remove a memory module under the following conditions. You can damage the computer and the module. Also, data will be lost. a.The computer is turned on.
  • Page 139 Optional Devices Removing the memory module cover 6. Fit the memory module’s connectors into the socket at about a 45 degree angle and push the module down until latches on either side snap into place. Align the notch of the memory module with that of the memory slot and gently insert the module into the slot.

  • Page 140: Removing Memory Module

    Optional Devices 7. Seat the memory module cover and secure it with one screw. Be sure that the cover is closed firmly. Seating the memory module cover 8. Install the battery pack. Refer to Replacing the battery pack section in Chapter 6, Power and Power-Up Modes, for details.

  • Page 141: Battery Pack

    Optional Devices 7. Grasp the module by the sides and pull it out. If you use the computer for a long time, the memory modules and the circuits located close to the memory modules will become hot. In this case, let them cool to room temperature before you replace them. Do not touch the connectors on the memory module or on the computer.

  • Page 142: Battery Charger

    Optional Devices Battery charger The battery charger provides a convenient way to charge battery packs without requiring the use of your computer. The battery charger holds up to two battery packs (lithium ion). Hard disk drive pack An extra HDD expands the flexibility of your system and lets you carry your data without carrying the computer.

  • Page 143: Installing The Hdd Pack

    Optional Devices 8. With the HDD in a vertical position, lift it straight up and away from the connector. HDD pack Plastic tab Removing the HDD pack Installing the HDD pack To install the HDD pack, follow the steps below. 1.

  • Page 144: Ultra Slim Bay Hdd Adaptor

    Optional Devices Ultra Slim Bay HDD adaptor You can increase your computer’s data storage capacity by installing an additional 40.0 billion bytes (37.26 GB), 60.0 billion bytes (55.89 GB), 80.0 billion bytes (74.53 GB) hard disk drive in the Ultra Slim Bay. To install an HDD in the Ultra Slim Bay HDD adaptor follow the steps below.

  • Page 145: Usb Floppy Disk Drive

    Optional Devices 3. Close the lid and slide the lock to the lock position. Hard disk drive Closing the lid For details on inserting the Ultra Slim Bay HDD adaptor in the computer’s Ultra Slim Bay slot, refer to Chapter 4, Operating Basics.

  • Page 146: I.link (Ieee1394)

    There is a possibility that the original data will be damaged. There is a particular risk that some frames will be deleted in the case of digital video transfer. TOSHIBA assumes no liability for such loss of data. Do not transfer data in areas where static electricity is easily generated or in areas subjected to electronic noise.
  • Page 147 Optional Devices Connecting 1. Make sure the connectors are properly aligned and plug the i.LINK (IEEE1394) cable into the computer. i.LINK (IEEE1394) connector i.LINK (IEEE1394) port Connecting the i.LINK(IEEE1394) cable into the computer 2. Plug the other end of the cable into the device. Note the following when you use i.LINK: You may need to install drivers for your i.LINK devices.

  • Page 148: Advanced Port Replicator Iil

    Optional Devices Advanced Port Replicator IIl In addition to the ports available on the computer, the Advanced Port Replicator lll provides a serial port and separate ports for PS/2 mouse and PS/2 keyboard. The Advanced Port Replicator connects directly to the docking interface on the underside of the computer.

  • Page 149: Parallel Printer

    7. Turn on the computer’s power. 8. Start the HW Setup program. Refer to Chapter 7, Setup. 9. Select the Parallel/Printer tab from the TOSHIBA HW Setup window. 10. Set the Parallel Port Mode and press OK. 11. Choose Reboot for the change to take effect.

  • Page 150: Security Lock

    Optional Devices Security lock Security locks enable you to anchor your computer and optional Advanced Port Replicator III to a desk or other heavy object to help prevent unauthorized removal of the computer or Advanced Port Replicator III. The computer has a security lock slot on the left side. Attach one end of a cable to a desk and the other end to the security lock slot.

  • Page 151: Troubleshooting

    PORTÉGÉ S100 Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring.

  • Page 152: Preliminary Checklist

    Troubleshooting Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. Make sure you turn on all peripheral devices before you turn on the computer.

  • Page 153: Hardware And System Checklist

    Troubleshooting Software The problems may be caused by your software or disk. If you cannot load a software package, the media may be damaged or the program might be corrupted. Try loading another copy of the software. If an error message appears while you are using a software package, check the software documentation.

  • Page 154: Self Test

    This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system, depending on how the Boot Priority is set in the TOSHIBA HW Setup program. If any of the following conditions are present, the self test failed: The computer stops and does not proceed to display information or messages except the TOSHIBA logo.

  • Page 155: Ac Power

    Troubleshooting AC power If you have trouble turning on the computer with the AC adaptor connected, check the DC IN indicator. Refer to Chapter 6, Power and Power-Up Modes for more information. Problem Procedure AC adaptor doesn’t Check the connections. Make sure the cord is power the computer firmly connected to the computer and a power (DC IN indicator does...
  • Page 156 Fully discharge the battery, then try to charge it again. Check the power consumption settings in TOSHIBA Power Saver utility. Consider using a power saving mode. User’s Manual...

  • Page 157: Real Time Clock

    5. Press Y key. BIOS setup will terminate and the computer will be rebooted. Password Problem Procedure Cannot enter Refer to the TOSHIBA Password Utility section in password Chapter 6, Power and Power-Up Modes. Keyboard Keyboard problems can be caused by your setup configuration. For more information refer to Chapter 5, Keyboard.

  • Page 158: Internal Lcd Display Panel

    Troubleshooting Internal LCD display panel Apparent LCD problems may be related to the computer’s setup. Refer to Chapter 7, Setup, for more information. Problem Procedure No display Press hotkeys Fn + F5 to change the display priority, to make sure it is not set for an external monitor.
  • Page 159 Troubleshooting DVD-ROM&CD-R/RW drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a Make sure the drive’s disc tray is securely CD/DVD in the drive closed. Press gently until it clicks into place. Check whether the drive power is on. If the power is off, click on the optical media drive icon in the task tray and turn on the power.

  • Page 160: Dvd Super Multi Drive

    Procedure Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: Use only media recommended by TOSHIBA. Do not use the mouse or keyboard during writing. Use only the software supplied with the computer for recording.
  • Page 161 Troubleshooting Some CD/DVDs run The software or hardware configuration may be correctly, but others do causing a problem. Make sure the hardware configuration matches your software’s needs. Check the CD/DVD's documentation. Check the type of CD/DVD you are using. The drive supports: DVD-ROM: DVD-ROM, DVD-Video CD-ROM:...

  • Page 162: Infrared Port

    Troubleshooting SD card Refer also to Chapter 8, Optional Devices. Problem Procedure SD card error occurs Reseat the SD card to make sure it is firmly connected. Check the card’s documentation. You cannot write to an Make sure the card is not write protected. SD memory card You cannot read a file Make sure the target file is on the SD memory...

  • Page 163: Touch Pad

    Troubleshooting Pointing Device If you are using a USB mouse, also refer to the section in this chapter and to your mouse documentation. Touch Pad Problem Procedure On-screen pointer The system might be busy. If the pointer is does not respond to shaped as an hourglass, wait for it to standby its Pad operation normal shape and try again to move it.

  • Page 164: Usb Mouse

    Troubleshooting USB mouse Problem Procedure On-screen pointer The system might be busy. If the pointer is does not respond to shaped as an hourglass, wait for it to resume its mouse operation normal shape and try again to move it. Make sure the mouse is properly connected to the USB port.
  • Page 165 Troubleshooting Memory expansion Refer also to Chapter 8, Optional Devices, for information on installing memory modules. Problem Procedure Beep sounds. Make sure the memory module installed in the memory slot is compatible with the computer. (Two beeps, a dash and a dot, for a If an incompatible module has been installed, defective memory follow the steps below.
  • Page 166 Troubleshooting External monitor Refer also to Chapter 8, Optional Devices, and to your monitor’s documentation. Problem Procedure Monitor does not turn Make sure that the external monitor’s power switch is on. Confirm that the external monitor’s power cable is plugged into a working power outlet.
  • Page 167 Troubleshooting Modem Problem Procedure Communication Make sure the computer’s internal modem software can’t initialize settings are correct. Refer to Phone and Modem modem Properties in the Control Panel. You can hear a dial If the call is going through a PBX machine, make tone but can’t make a sure the communication application’s tone dial call...

  • Page 168: Wireless Lan

    Troubleshooting Problem Procedure Cannot access LAN Check for a firm cable connection between the LAN jack and the LAN HUB. Wake-up on LAN does Make sure the AC adaptor is connected. not work The Wake-up on LAN function consumes power even when the system is off. If problems persist, consult your LAN administrator.

  • Page 169: Toshiba Support

    Troubleshooting TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first.
  • Page 170 Troubleshooting 9-20 User’s Manual...

  • Page 171: Specifications

    PORTÉGÉ S100 Appendix A Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Weight 1.99 kilograms, configured with: 14”XGA, 256MB RAM, (typical) 40GB HDD, DVD-ROM&CD-R/RW drive, modem, LAN (100M Bit), Wireless LAN, 6cell battery pack. Weight will vary with other configurations. Above weights are measured at a specific criteria.
  • Page 172 Specifications Built-in Modem Network control unit (NCU) Type of NCU Type of line Telephone line (analog only) Type of dialing Pulse Tone Control command AT commands EIA-578 commands Monitor function Computer’s speaker Communication specifications Communication Data: Full duplex system Fax: Half duplex Communication Data...

  • Page 173: Display Controller And Modes

    PORTÉGÉ S100 Appendix B Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. The display controller supports VGA, SVGA and XGA modes at internal LCD display panel. SXGA+ model supports SXGA and SXGA+ in addition to VGA, SVGA and XGA modes.
  • Page 174 Display Controller and Modes Table1 Video modes (VGA) Video Type Resolution Character Colors Scanning mode matrix (pels) frequency Vertical (Hz) 0, 1 40 × 25 8 × 8 16 of 256K Text Characters 2, 3 80 × 25 8 × 8 16 of 256K Text Characters...
  • Page 175 Display Controller and Modes Table1 Video modes (VGA) continued Video Type Resolution Character Colors Scanning mode matrix (pels) frequency Vertical (Hz) 320 × 200 8 × 8 16 of 256K Grph Pels 640 × 200 8 × 8 16 of 256K Grph Pels 640 ×...
  • Page 176 Display Controller and Modes Table 2 Video modes (XGA model) Resolution LCD colors CRT colors Vertical frequency (Hz)* 640 × 480 256/256K 256/256K 800 × 600 256/256K 256/256K 1024 × 768 256/256K 256/256K 1280 × 1024 256/256K 256/256K (Virtual with LCD only) 1600 ×...
  • Page 177 Display Controller and Modes Table 2 Video modes (XGA model) continued Resolution LCD colors CRT colors Vertical frequency (Hz)* 640 × 480 64K/64K 64K/64K 800 × 600 64K/64K 64K/64K 1024 × 768 64K/64K 64K/64K 1280 × 1024 64K/64K 64K/64K (Virtual with LCD only) 1600 ×...
  • Page 178 Display Controller and Modes Table 2 Video modes (XGA model) continued Resolution LCD colors CRT colors Vertical frequency (Hz)* 640 × 480 16M/16M 16M/16M 800 × 600 16M/16M 16M/16M 1024 × 768 16M/16M 16M/16M 1280 × 1024 16M/16M 16M/16M (Virtual with LCD only) 1600 ×...
  • Page 179 Display Controller and Modes Table 3 Video modes (SXGA+ model) Resolution Vertical colors colors frequency (Hz)* 640 × 480 256/256K 256/256K 800 × 600 256/256K 256/256K 1024 × 768 256/256K 256/256K 1280 × 1024 256/256K 256/256K 1400 × 1050 256/256K 256/256K 1600 ×...
  • Page 180 Display Controller and Modes Table 3 Video modes (SXGA+ model) continued Resolution LCD colors CRT colors Vertical frequency (Hz)* 640 × 480 64K/64K 64K/64K 800 × 600 64K/64K 64K/64K 1024 × 768 64K/64K 64K/64K 1280 × 1024 64K/64K 64K/64K 1400 × 1050 64K/64K 64K/64K 1600 ×...
  • Page 181 Display Controller and Modes Table 3 Video modes (SXGA+ model) continued Resolution LCD colors CRT colors Vertical frequency (Hz)* 640 × 480 16M/16M 16M/16M 800 × 600 16M/16M 16M/16M 1024 × 768 16M/16M 16M/16M 1280 × 1024 16M/16M 16M/16M 1400 × 1050 16M/16M 16M/16M 1600 ×...
  • Page 182 Display Controller and Modes B-10 User’s Manual...

  • Page 183: Wireless Lan

    PORTÉGÉ S100 Appendix C Wireless LAN Card Specifications Form Factor Mini PCI Type III IEEE 802.11 Standard for Wireless LANS Compatibility Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The ‘Wi-Fi CERTIFIED’ logo is a certification mark of the Wi-Fi Alliance. Microsoft Windows ®...

  • Page 184: Supported Frequency Sub-Bands

    Subject to the radio regulations that apply in the countries/regions, your Wireless LAN card may support a different set of 5 GHz/2.4 GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in the countries/regions.
  • Page 185 Wireless LAN 2457* 2462 2467* 2472* *1 Factory-set default channels *2 Refer to the sheet Approved Countries/Regions for use for the countries/regions that in which these channels can be used. When installing Wireless LAN cards, the channel configuration is managed as follows: For wireless clients that operate in a Wireless LAN Infrastructure, the Wireless LAN card will automatically start operation at the channel...
  • Page 186 5520 5540 5560 5580 5600 5620 5640 5660 5680 5700 5745 5765 5785 5805 User’s Manual...

  • Page 187: Appendix D : Toshiba Raid

    PORTÉGÉ S100 Appendix D TOSHIBA RAID TOSHIBA RAID (Redundant Array of Independent Disks) realizes fault tolerance, which is configured by arraying multiple independent hard disk drives. 2 hard disk drives (built-in HDD and optional Ultra Slim Bay HDD) can be used to construct a RAID-1 (mirroring) configuration.

  • Page 188: Setting Up Windows Manually

    Creating the TOSHIBA RAID Driver Floppy Disk 1. Connect the USB floppy disk drive (optional) and insert a floppy disk. 2. Locate the TOSHIBA RAID Driver in the Tools & Drivers Depository on your HDD (‘C:\TOOLSCD\RAID driver’ folder). 3. Copy all files from this folder to the floppy disk.
  • Page 189 Therefore, to ensure that such situations do not happen, perform RAID-1 media checks regularly. The TOSHIBA RAID Console is set by default to perform media checks once a month. User’s Manual...

  • Page 190: Starting, Modifying And Ending The Bios Setup Program

    TOSHIBA RAID Starting, Modifying and Ending the BIOS Setup Program Starting the BIOS Setup Program 1. Switch on your computer while pressing the Esc key. If Password = is displayed, enter the user password and press the Enter key. Please refer to Chapter 6, the...

  • Page 191: Ending The Bios Setup Program

    3. The Execute Creation message is displayed once the configuration is modified. Move the cursor to the appropriate location and press the space bar to continue. Pressing the Home key will revert the modified Create State settings back to the Current State settings. 4.
  • Page 192 User’s Manual...

  • Page 193: Ac Power Cord And Connectors

    PORTÉGÉ S100 Appendix E AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 2 meters...
  • Page 194 For the United States and Canada, two pin plug configuration must be a 2-15P (250V) or 1-15P (125V) and three pin plug configuration must be 6-15P (250V) or 5-15P (125V) as designated in the U.S. National Electrical code handbook and the Canadian Electrical Code Part II. The following illustrations show the plug shapes for the U.S.A.

  • Page 195: Appendix F : If Your Computer Is Stolen

    What is your address, phone, and fax number? To register the theft on paper, please follow these procedures: Fill in the TOSHIBA Theft Registration form (or a copy of it) below. Attach a copy of your receipt showing where your computer was purchased.

  • Page 196: Toshiba Theft Registration

    If your computer is stolen TOSHIBA Theft Registration Send to: TOSHIBA Europe GmbH Technical Service and Support Leibnizstr. 2 93055 Regensburg Germany Fax number: +49 (0) 941 7807 921 Country stolen: Machine type: (e.g. Satellite A50) Model number: (e.g. PSA50 YXT) Serial number: (e.g.
  • Page 197 PORTÉGÉ S100 Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference. Abbreviations AC: alternating current AGP: accelerated graphics port ANSI: American National Standards Institute APM: advanced power manager ASCII: American Standard Code for Information Interchange BIOS: basic input output system CD-ROM: Compact Disc-Read Only Memory CD-RW: Compact Disc-ReWritable...
  • Page 198 Glossary IrDA: Infrared Data Association IRQ: interrupt request KB: kilobyte LCD: liquid crystal display LED: light emitting diode LSI: large scale integration MB: megabyte MS-DOS: Microsoft Disk Operating System OCR: optical character recognition (reader) PCB: printed circuit board PCI: peripheral component interconnect RAM: random access memory RGB: red, green, and blue ROM: read only memory...
  • Page 199 Glossary analog signal: A signal whose characteristics such as amplitude and frequency vary in proportion to (are an analog of) the value to be transmitted. Voice communications are analog signals. ANSI: American National Standards Institute. An organization established to adopt and define standards for a variety of technical disciplines. For example, ANSI defined the ASCII standard and other information processing requirements.
  • Page 200 Glossary bus: An interface for transmission of signals, data or electric power. byte: The representation of a single character. A sequence of eight bits treated as a single unit; also the smallest addressable unit within the system. cache memory: High speed memory which stores data that increases processor speed and data transfer rate.
  • Page 201 Glossary compatibility: 1) The ability of one computer to accept and process data in the same manner as another computer without modifying the data or the media upon which it is being transferred. 2) the ability of one device to connect to or communicate with another system or component.
  • Page 202 Glossary delete: To remove data from a disk or other data storage device. Synonymous with erase. device driver: A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on. dialog box: A window that accepts user input to make system settings or record other information.
  • Page 203 (FDD): An electromechanical device that reads and writes to floppy disks. Fn-esse: A TOSHIBA utility that lets you assign functions to hot keys. folder: An icon in Windows used to store documents or other folders. format: The process of readying a blank disk for its first use. Formatting establishes the structure of the disk that the operating system expects before it writes files or programs onto the disk.
  • Page 204 Fn, can be used to set system parameters, such as speaker volume. HW Setup: A TOSHIBA utility that lets you set the parameters for various hardware components. icon: A small graphic image displayed on the screen or in the indicator panel.
  • Page 205 Glossary jumper: A small clip or wire that allows you to change the hardware characteristics by electrically connecting two points of a circuit. K: Taken from the Greek word kilo, meaning 1000; often used as equivalent to 1024, or 2 raised to the 10th power. See also byte and kilobyte.
  • Page 206 Glossary mode: A method of operation, for example, the boot mode, standby mode or the hibernation mode. modem: Derived from modulator/demodulator, a device that converts (modulates) digital data for transmission over telephone lines and then converts modulated data (demodulates) to digital format where received.
  • Page 207 The electrical connection through which the computer sends and receives data to and from devices or other computers. Power Saver Utility: A TOSHIBA utility that lets you set the parameters for various power-saving functions. printed circuit board (PCB): A hardware component of a processor to which integrated circuits and other components are attached.
  • Page 208 Glossary restart: Resetting a computer without turning it off (also called “warm boot” or “soft reset”). See also boot. RGB: Red, green, and blue. A device that uses three input signals, each activating an electron gun for a primary additive color (red, green, and blue) or port for using such a device.
  • Page 209 TFT display: A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology with thin film transistor (TFT) to drive each cell. Touch Pad: A pointing device integrated into the TOSHIBA computer palm rest. TTL: Transistor-transistor logic. A logic circuit design that uses switching transistors for gates and storage.
  • Page 210 Glossary Glossary-14 User’s Manual...
  • Page 211 Advanced Port Replicator III, 1-16, brightness increase, 5-5 8-16 controller, B-1 ASCII characters, 5-9 hinge, 2-7 opening, 3-6 DLA for TOSHIBA, 1-15, 4-15 Docking interface, 1-6, 2-6 Battery Documentation list, 1-2 charging, 6-8 DVD Super Multi drive, 1-5 extending life, 6-11...
  • Page 212 Index LCD screen brightness increase, Floppy disk care, 4-19 power save mode, 5-4 Fn + Ctrl (enhanced keyboard sound mute, 5-3 simulation), 5-3 standby, 5-4 Fn + Enter, 5-3 wireless setting, 5-5 Fn + Esc (sound mute), 5-3 HW Setup, 1-12 Fn + F1 (instant security), 5-4 accessing, 7-1 Fn + F10 (Arrow mode), 5-3...
  • Page 213 Index Keypad overlay, 1-9, 5-7 Arrow mode, 5-7 NVIDIA Rotation Settings, 1-14 Numeric mode, 5-8 temporarily using normal keyboard (overlay on), 5-8 Password temporarily using overlay (overlay power on, 1-10 off), 5-8 problems, 9-7 turning on the overlays, 5-7 starting the computer by, 6-16 Supervisor, 6-15 user, 6-14 LAN, 1-7, 4-25...
  • Page 214 TOSHIBA Controls, 1-12 Wireless LAN, 9-18 TOSHIBA Mic Effect, 1-13 Processor, 1-3 TOSHIBA Mobile Extension, 1-13 TOSHIBA PC Diagnostic Tool, 1-13 TOSHIBA Power Saver, 1-12 RecordNow!, 1-12, 4-14 TOSHIBA Presentation button, 1-9 Recovery Media, 3-12 TOSHIBA SD Memory Boot Utility,...
  • Page 215 Index Ultra Slim Bay, 2-4 Video modes, B-1 changing modules, 4-3 Video RAM, 1-3 HDD adaptor (Black), 8-12 Volume control, 2-2 location of slot, 2-4 modules, 1-8 options, 1-17 Wireless communication, 4-23 weight saver, 1-8 indicator, 2-10, 4-25 USB, 1-6 Wireless communication switch, 1-8, location, 2-4 2-1, 4-24...
  • Page 216 Index Index-6 User’s Manual...

Table of Contents