Table of Contents
Advertisement
System Configuration
When the adjustment has been made, or if no
adjustment is required and all settings on this
page are complete, press the
⁄
/
¤
F until the on-screen cursor is
Button
pointing to
and then press the
PAGE 1
Q to return to the main
Set Button
menu to configure another
IN/OUT SETUP
input, or if no further input configuration adjust-
⁄
ments are needed, press the
/
¤
F until the on-screen cursor is
Button
pointing to
and then press
MASTER MENU
Q to return to the main
the Set Button
menu screen.
Video Monitor Settings
The
VIDEO MONITOR SETTINGS
menu (Figure 10) is unique in that it contains a
mix of information display lines that detail status
information about the AVR 645's video system
settings, along with a few lines where a specific
parameter may be changed. With the
on the screen, press the
⁄
MENU
F until the on-
Navigation Button
screen cursor is pointing to
VIDEO
and then press the
MONITOR SETTINGS
Q to move to the menu
Set Button
screen.
* V I D E O
M O N I T O R
S E T T I N G S *
I N
V I D E O
F O R M A T :
1 0 8 0 i
I N
V I D E O
C O P Y
P R O T :
O N
V I D E O
P R O C E S S :
V
C O N V E R S
→
C O M P O N E N T
O U T :
O F F
S - V I D E O
O U T :
O F F
C O M P O S I T E
O U T :
O F F
D I S P L A Y
I N T E R :
H D M I / D V I
H D M I
A U D I O
O U T :
N O
B A C K
T O
M A S T E R
M E N U
Figure 10
26 SYSTEM CONFIGURATION
The
I N VIDEO FORMAT
tional display of the resolution of the incoming
Navigation
video stream, and may not be adjusted.
The
I N VIDEO COPY PROT
informational display that shows whether or not
an incoming video signal contains copy
protection encoding, and may not be adjusted.
The
VIDEO PROCESS
Navigation
tional display of the setting made in the
IN/OUT SETUP
incoming video is processed for the input being
viewed, and may not be adjusted.
The
COMPONENT OUT
tional display of whether or not the Component
Video outputs are
on the input signal type and resolution, and
whether or not the incoming video signal has
HDCP content protection. It may not be adjusted.
The
S-VIDEO OUT
MASTER
display of whether or not the S-video outputs are
/
¤
available at a 576i resolution (or OFF), based on
the input signal type and resolution and whether
or not the incoming video signal has HDCP
content protection. It may not be adjusted.
The
DISPLAY INTER
choose between an
default value and an HDMI/DVI output by press-
ing the
Navigation Button
/
‹
›
make the desired selection. When the setting is
, the HDMI output is placed in a
ANALOG
Standby mode so that it automatically switches
to HDMI when an HDMI signal is detected. If a
high-definition input source is not HDCP-content-
protected, it may be output through the compo-
nent jacks; otherwise, it will be sent only to the
HDMI outputs. The
all converted or processed video to the HDMI
outputs.
The
HDMI AUDIO OUT
choose whether a two-channel downmix of the
audio that accompanies the selected source is
sent over the HDMI connection (
maximum bit rate the display's audio system is
capable of handling, or not (
setting, press the
F to make the desired selection.
When required adjustments have been made for
this input, or if no adjustment is required, press
the
⁄
Navigation Button
/
¤
the on-screen cursor is pointing to
MASTER MENU
Q to return to the main menu screen.
line is an informa-
line is an
line is an informa-
menu indicating how
line is an informa-
or
, based
ENABLED
OFF
line is an informational
line allows you to
video output
ANALOG
F to
setting routes
HDMI/DVI
line allows you to
) at the
YES
). To change the
N O
Navigation Button
‹
/
›
F until
BACK T O
and then press Set Button
Audio Setup
This menu allows you to configure the tone con-
trols. If you do not wish to change any of those
settings at this time, proceed to the next menu
screen. However, to make configuration changes
to those parameters, make certain that the
is on the screen with the ➞
MASTER MENU
cursor pointing to the
AUDIO SETUP
Q. The
and press the Set Button
menu (Figure 12) will appear.
AUDIO SETUP
*
A U D I O
S E T U P
*
→
T O N E
:
I N
O U T
B A S S
: 0
T R E B L E
: 0
B A C K
T O
M A S T E R
M E N U
Figure 12
The first line controls whether or not the
bass/treble tone controls are in the signal path.
The normal default is for them to be in-line, but if
you wish to remove them from the circuit for
"flat" response, first make certain that the ➞
cursor is pointing to the
line on the
TONE
menu and press the
Navigation Button
/
‹
›
F so that
is highlighted in reverse
OUT
video.
If you wish to leave the tone controls in the sig-
nal path, the amount off boost or cut for bass
and treble may be adjusted by pressing the
F so that the
Navigation Button
⁄
/
¤
➞ cursor is next to the line for the setting you
wish to adjust. Next, press the
‹
/
›
F until the desired setting is
Button
shown.
When all desired changes have been made on
this menu, press the
Navigation Button
⁄
/
¤
F so that the ➞ cursor is next to the
line and press
B A C K T O M A I N M E N U
Q.
the Set Button
line,
Navigation
Hide quick links:
Advertisement
Table of Contents
