Table of Contents
Advertisement
Operation
6-Channel Direct Input
The AVR5000 is equipped for future expansion
through the use of optional, external adapters for
formats that the AVR5000 may not be capable of
processing. When an adapter is connected to the
6-Channel Direct Input
, you may select it
by pressing the 6-Ch Direct Input Selector
. The 6-Channel Direct Input may also be
selected by pressing the Input Source Selector
button
on the front panel until the words
appear in the Main
Information Display
, and a green LED
lights next to 6 CH in the Input Indicators
Note that when the 6-Channel Direct Input is in
use, you may not select a surround mode, as the
external decoder determines processing. In addi-
tion, there is no signal at the record outputs
when the 6-Channel Direct Input is in use, and
the Tone
and Balance
not be effective.
Memory Backup
This product is equipped with a memory backup
system that preserves tuner presets and system
configuration information if the unit is turned off
completely, accidentally unplugged or subjected
to a power outage. This memory will last for
approximately two weeks, after which time all
information must be reentered.
Tuner Operation
The AVR5000's tuner is capable of tuning AM, FM
and FM Stereo broadcast stations and receiving
RDS data. Stations may be tuned manually, or
they may be stored as favorite station presets and
recalled from a 30 position memory.
Station Selection
1. Press the AM/FM Tuner Select button
on the remote to select the tuner as an input. The
tuner may be selected from the front panel by
either pressing the Input Source Selector
.
until the tuner is active or by pressing the Tuner
Band Selector
2. Press the AM/FM Tuner Select button
or Tuner Band Selector
between AM and FM so that the desired frequen-
cy band is selected.
controls will
3. Press the Tuner Mode button
remote or hold the Band Selector
front panel pressed for 3 seconds to select manu-
al or automatic tuning.
When the AUTO indicator
Main Information Display the tuner will only stop
at those stations that have a strong enough signal
to be received with acceptable quality.
When the AUTO indicator
the tuner is in a manual mode and will stop at
each frequency increment in the selected band.
4. To select stations press any Tuning button
. When the AUTO indicator
ated, press the button to cause the tuner to
search for the next highest or lowest frequency
station that has an acceptable signal or hold the
button pressed to tune more quickly and release
it to start the auto search. In the Auto mode the
tuner will play each station in stereo or mono
mode, just as the program is transmitted. If the
AUTO indicator
Tuning button
cy increment at a time, or press and hold it to
locate a specific station. When the TUNED indi-
cator
illuminates, the station is properly tuned
and should be heard with clarity.
5. Stations may also be tuned directly by pressing
the Direct button
Numeric Keys
tion's frequency. The desired station will auto-
matically be tuned after the latest number is
entered. If you press an incorrect button while
entering a direct frequency, press the Clear but-
ton
NOTE: When the FM reception of a stereo
station is weak, audio quality will be increased
by switching to Mono mode by pressing the
Tuner Mode button
ing the Band Selector
pressed for 3 seconds until the
at any time.
indicator
Preset Tuning
again to switch
Using the remote, up to 30 stations may be
stored in the AVR5000's memory for easy recall
using the front panel controls or the remote.
on the
To enter a station into the memory, first tune the
on the
station using the steps outlined above. Then:
1. Press the Memory button
Note that
is illuminated in the
nate and flash in the Main Information
Display
2. Within five seconds, press the Numeric Keys
is not illuminated,
wish to store this station's frequency. Once
entered, the preset number will appear in the
Preset Number/Sleep Time Display
3. Repeat the process after tuning any additional
is illumin-
stations to be preset.
Recalling Preset Stations
• To manually select a station previously entered
in the preset memory, press the Numeric Keys
memory location.
• To manually tune through the list of stored pre-
is not illuminated, tap the
set stations one by one, press the Preset
to advance one frequen-
Stations Selector buttons
panel or remote.
, and then pressing the
that correspond to the sta-
to start over.
on the remote or hold-
on the front panel
goes out.
on the remote.
indicator
will illumi-
.
corresponding to the location where you
that correspond to the desired station's
on the front
OPERATION 33
.
Hide quick links:
Advertisement
Table of Contents
